How long does it take for the refrigerator to be powered on for the fresh keeping room to cool?

The new refrigerator can be powered on for about 3 to 6 hours before it can be put in, which can effectively prevent problems with the oil circuit. After the new refrigerator is plugged in, it needs to be run for a period of time without putting in items, and then put in items after the temperature is lowered, so as to better protect the refrigerator.

2. What should be paid attention to before using the new refrigerator.

1. After moving to a new house, do not plug in the power supply immediately, but need to open all the doors of the air conditioner, take out the internal freezers, expose them to the air for a period of time, and wait until the internal odor has dissipated, and then stuff the freezer into the refrigerator, close the refrigerator door, and then plug in the power supply.

2. Prepare a clean towel, soak it, then wring out the water of the towel, and then wipe all surfaces inside the refrigerator with a towel to clean up the stains. After the interior is cleaned, the outer surface of the refrigerator needs to be cleaned. In addition, it should be noted that the refrigerator needs to be placed in a ventilated area to enhance the service life.

3. Check whether all accessories in the refrigerator are installed in place, and check whether the filter plug is put on the drain at the lower part of the refrigerator room. And when you turn on the machine for the first time, you should make sure that the indoor temperature is not too low, otherwise it is easy to cause damage to the refrigerator and affect the use.

Theoretically, as long as the refrigerator is powered on and the refrigeration system can work normally, the actual temperature in the refrigerator will continue to decrease.

When the refrigerator is running normally for about 1 hour, the temperature in the refrigerator will be significantly lower.

If the actual temperature in the refrigerator room of the refrigerator is still not significantly reduced after 1 hour of operation, it means that the refrigerator has an abnormal fault, and the manufacturer's after-sales maintenance personnel should be found to check and repair.

Under normal circumstances, the refrigeration room also starts to work at the same time after the power is turned on, that is, refrigeration, but to reach the temperature of refrigeration, the temperature of refrigeration can be reached in about half an hour.

If you buy a new refrigerator, it will take about 2 to 6 hours to turn on the power.

If it is a refrigerator after moving, it is decided according to the length of the moving time, and for those that are not far away and the time is short, it can be energized about 5 minutes after moving. However, if it is a long distance and a long time, it needs to be left for about 30 minutes before turning on the power.

Precautions for moving the refrigerator

1. When moving the refrigerator, you must first unplug its power plug and take out all the food inside. Then use tape to fix the shelves in the refrigerator and the drawers in the freezer compartment and other moving parts, and then close the refrigerator door after the inside is fixed, and then fix it with tape to avoid damage during the movement.

2. In the process of moving and transporting the refrigerator, it is necessary to avoid bumps and violent vibrations, and at the same time, it is also necessary to prevent it from being eroded by rain.

3. When handling the refrigerator, you must start from the bottom of it, not only grasp its doorknob and top plate frame, but also follow the principle of gentle lifting and handling, so as not to damage the box and other components.

4. After the refrigerator is transported, it cannot be powered on immediately, and it must be placed for about 3 hours before it can be powered on, so as not to affect the service life of the compressor. Because after the refrigerator is transported, the refrigerant in the internal cooling pipe is shaken, and the refrigerant can only be energized after the refrigerant is fully reflowed, so as not to affect its refrigeration effect.

After the refrigerator is bought, it needs to stand for at least two hours before it can be used with electricity, note that if the ambient temperature is low, the time needs to be longer. Because in the summer, the lubricant inside is circulating and presents a liquid state, and the standing time can be two or three hours. However, if it is in winter, the internal lubricant may freeze and become solid, and the standing time should be extended, and it can be used with electricity after standing for about 6 hours.

Introduction: 1. The reason why the refrigerator needs to stand for so long is mainly because of the bumps in the process of operation, if the bumps are more serious and there is a tilt, the lubricating oil in it will flow into the cylinder of the compressor. After buying, if it is put into use immediately, the lubricating oil will be hindered to a certain extent and will not be able to flow.

2. If the compressor wants to operate normally, it needs lubricating oil, but there is lubricating oil in the cylinder, which will affect the work of the compressor and seriously cause the refrigerator to be paralyzed. Therefore, it is necessary to let the lubricating oil stand for two or three hours before it can be used.

1. If it is a short distance movement and only a slight inclination, then it can be energized after about 5 to 10 minutes. Because the refrigerator has a small moving distance, the refrigerant only shakes slightly, and it can be powered on after about 5 to 10 minutes of impurities precipitation.

2. If the refrigerator has a long handling distance and the handling angle is less than 45 degrees, then it needs to be placed for at least 2 hours after the handling is completed before it can be powered on. Because after the refrigerator is tilted, the oil in the compressor will flow into the refrigeration pipe, and you need to wait for the oil to return to the compressor before starting the refrigerator, otherwise it will easily cause the refrigeration pipe to clog.

3. If the refrigerator needs to be placed lying down during the handling process, then it needs to be placed for at least 2 hours before it can be powered on after the handling is completed. Because it is placed lying down, all the oil from the compressor will flow out, and it will take at least 2 hours to return to the compressor, otherwise the compressor will be damaged.

The situation to pay attention to when handling the refrigerator

1. If it is a refrigerator that has been put into use, before handling, you need to cut off the power supply, and then take out all the ingredients and items inside.

2. After the refrigerator is emptied, it needs to be cleaned, and then the internal laminate should be fixed with tape, including the humidor box, drawer, etc., to avoid shaking during transportation. If you don't want to fix it with tape, you can remove all the movable items inside and reinstall them when the transportation is complete.

3. When carrying the refrigerator, keep it upright as much as possible to move, and if you need to tilt, the tilt angle should not exceed 45 degrees. Because there is oil in the compressor, it will enter the refrigeration pipeline after tilting, and improper handling will easily affect the service life of the refrigerator.

The refrigerator can be used for 2 to 4 hours before it can be powered on.

Generally, after the new refrigerator arrives at home, it needs to stand for 2 to 4 hours before it can be turned on. However, according to the general situation, it will be left for 24 hours to allow the lubricating oil to flow back into the compressor. In addition, the new refrigerator also needs to be cleaned when you buy it, so that the odor in the refrigerator can be used to make it more safe.

Precautions for refrigerator use

1. Summer is the peak period for using the refrigerator, and the ambient temperature at this time is very high, and the temperature difference between the inside and outside of the refrigerator is very large.

2. When placing the refrigerator, it should keep a certain distance from the wall, not close to the wall, and do not place too many sundries on the top of the refrigerator, especially not some electrical appliances.

3. When you first start using the refrigerator, you should first check whether the power supply voltage of your home is consistent with the voltage marked on the refrigerator, and it can only be used if it is consistent. In addition, use a separate outlet for the refrigerator, not the same as other appliances.

4. Don't always open and close the refrigerator door when you're okay to reduce the overflow of air conditioning.

The refrigerator should be left for 3-6 hours before it is powered on. New refrigerators must sit for at least two hours before they can be powered on, depending on the current temperature. If in the summer, the refrigerant inside can flow, it can be left for two or three hours to turn on electricity.

If it is winter, because the temperature is very low and the refrigerant flows slowly, it is recommended to let it stand for a little longer, and it is recommended to let it stand for more than six hours.

Why should a new refrigerator sit before it can be powered on1. Since the operation of the refrigerator compressor needs lubricating oil protection, the manufacturer injects a certain amount of special lubricating oil into the refrigeration system during the production process. Once the refrigerator is made, the lubricating oil and refrigerant are completely enclosed in the refrigeration system.

2. The refrigerator has been bumped, moved, or even tilted for several hours before being transported home. At this point, the lubricating oil in the refrigerator will flow along the pipes into the coil of the heat exchanger, and a small amount of lubricating oil will also flow into the compression chamber of the compressor due to turbulence and vibration. At this time, after the refrigerator is turned on, it is easy to paralyze the refrigeration system.

So, to be on the safe side, it is right to leave the refrigerator for one to two hours before turning it on.

The new refrigerator should be left on for 2 hours before turning it on, and it can be turned on for 1 hour before putting things on.

1. The main purpose is to prevent the refrigerator from running the refrigerated oil into the pipeline during transportation, and the refrigerated oil will reset and return to the compressor after 2 hours of stationation, so as to ensure that the compressor works in a good state and avoid burning out the compressor.

2. In addition, it is necessary to work for a period of time with electricity, and it is best to reach the set temperature before putting the food in after the refrigerator is shut down, which is also to ensure that the working load of the refrigerator is not increased, so as to achieve the purpose of saving electricity.

Hope mine can help you.

You can put things in two hours after powering it on, but I recommend that you make sure to clean the refrigerator thoroughly before turning it on.

Hello, I'm glad to answer for you, and the reason for this lies in the lubricating oil of the refrigerator refrigeration system. We know refrigerator compressors.

The operation needs to be protected by lubricants, so the manufacturer fills the refrigeration system with a certain amount of special lubricating oil during the production process, and the lubricating oil and refrigerant are completed after the refrigerator is made.

It is completely enclosed in the refrigeration system.

When the appliance manufacturer delivers a new refrigerator to your home, it is brought from the warehouse.

The refrigerator has already gone through an hour of bumps, movement and even tilting, and the lubricating oil in the refrigerator will flow into the coil of the heat exchanger along the pipeline; A small amount of lubricating oil is also poured into the compression chamber of the compressor – the cylinder – under the action of jolting and vibration. If the machine is started and running at this time, the flow of refrigerant will be directly affected due to the obstruction of lubricating oil in the pipeline; Second, because the function of the cylinder is to compress the gaseous refrigerant, if there is a certain amount of lubricating oil in the cylinder, it will affect the work of the compressor, and the cylinder will be completely damaged by liquid shock, so that the refrigerator refrigeration system will be paralyzed.

Newly bought refrigerator, who is willing to let it be scrapped? It's better to wait for two or three hours to allow the refrigeration oil to settle down completely. By the way, don't forget to open all the refrigerator doors and drawers to let the smell of the refrigerator go.

Although the newly bought refrigerator is not as good as wooden furniture, there is a certain odor, you don't want to eat plastic-smelling food, right?

Once the new refrigerator is powered on, it is best to wait thirty minutes for the refrigerator to run normally and the temperature to reach the set value before putting the food in.

How to use the refrigerator thermostat In the process of use, the working time and power consumption of the refrigerator are greatly affected by the ambient temperature, so we need to choose different gears to use in different seasons.

When the ambient temperature is high in summer, it should be used in a weak gear, and when the ambient temperature is low in winter, it should be used in a strong gear, the reason: in summer, the ambient temperature is higher (up to 30), and the temperature in the freezer room is higher (up to 30), and the temperature in the freezer room is below -18, and the temperature difference between inside and outside is large, so it is difficult for the temperature in the box to drop by 1.

How to maintain the refrigerator:

1. In addition to cleaning and disinfecting the conventional parts of the refrigerator, we should pay more attention to the use of efficient refrigerator special disinfectants to spray disinfect the drip trough, partition trough and other dead corners inside the refrigerator.

2. After the spraying of the inner wall and dead corner of the refrigerator is completed, the refrigerator door should be closed for 5-10 minutes to allow the disinfectant to be fully sterilized, and finally wiped clean with a rag.

3. Wipe the surface of the refrigerator at least once a week.

4. If there is grease or dust, wipe it with warm water.

5. The inside of the refrigerator can be wiped with boric acid or disinfectant tissues, and the shelves should be taken out and cleaned with water.

6. Wipe the inner wall of the refrigerator with glycerin to form a thin protective film, even if it is stained with milk or food residues, it can be easily wiped off.

7. Sometimes vinegar is used instead of boric acid, which can better prevent the formation of rust.

8. Wipe the refrigerator with boric acid, which can be easily defrosted.

9. Be sure to cut off the power supply before cleaning.

Don't turn on the new refrigerator immediately, do these 3 things well, the refrigerator has a good cooling effect and a long service life.

1. When the refrigerator starts for the first time, it takes a long time to shut down the refrigeration, about two hours, and the specific time also has a certain relationship with the performance of the compressor. 2. Under normal use, the temperature will decrease about 10 minutes after the refrigerator is started, and there is already a refrigeration effect at this time, but it takes about 25 to 35 minutes to reach the set temperature, and it will stop at this time. How to take care of it:

1. If you do not use the refrigerator for a long time, you need to cut off the power of the refrigerator, and then take out all the things inside. 2. It is recommended to clean the inside of the refrigerator regularly after a long time of opening, because after a long period of use, a lot of food will leave a certain amount of residue, and it will also produce certain bacteria. 3. Try not to make too much food in the refrigerator during the process of using the refrigerator, too much food stored will lead to poor cold air circulation in the refrigerator, which will affect the refrigeration effect of the refrigerator in the long run, and the preservation function of the food is not so good.