How do I clean my camera? How to clean the camera

The first is the cleaning of the shell, which can be wiped with a wet paper towel quickly, not too wet, in this way, it is easy to accidentally enter the water into the camera, so it is not good, after all, the camera is a relatively expensive instrument, generally water is easy to break, even if it is not broken, it is easy to affect the quality of the photos taken. When the wet paper towel is wiped quickly, it is necessary to use the dry one to wipe out the moisture brought by the wet paper towel.

Then there is the wiping of the lens, this must be careful, must be wiped with professional lens polish, otherwise it is easy to wear the lens, this is not greedy for cheap and trouble-free, the general professional lens polishing paper will not hurt the lens, and it is not like some paper will produce some confetti or dust. After these two cleanings, it's basically okay. The rest is your usual storage, it is recommended to buy a special bag for the camera, so that whether you take it out for use or idle at home, it will not get any stains in the process, and it is more convenient.

1.Please turn on the camera to open the lens cap.

2.Turn the camera so that the lens is facing the ground. Gently blow the lens to release any stray particles.

3.If you still notice particles on the edges of the lenses, gently remove them with a small, soft brush.

4.Gently wipe the lens with a microfiber cloth, moving in a circular motion. Start in the middle of the shot and work your way up the edges.

5.If the microfiber cloth doesn't remove all the dirt or smudge, use a few drops of lens cleaning solution or water. Place the ink droplets on the cloth instead of on the lens.

Then repeat the circular motion of the cloth. Start by using the wet area of the cloth, then repeat the movement with the dry area of the cloth.

The lens is the most important part of the camera, try to keep the lens clean, avoid getting dirty, wiping it off frequently, and fluffing the lens, and cover it with the lens cover when not in use. If there is dust on the lens, you can wipe it off with a soft-bristled brush (lens brush from a camera equipment store**) or blow it off with a rubber blow ball. If there are fingerprints on the lens, you can apply detergent (wipe lens water), gently dry it with lens paper or clean suede, wipe it around a circle, do not wipe it horizontally and vertically, and do not use ordinary handkerchiefs, paper or placket to wipe hard, and it is also forbidden to rub excessive gasoline and alcohol, because gasoline and alcohol are easy to dissolve the adhesive between the lenses.

Take a basin of water, then throw the camera inside, wipe it clean with a cloth, take it out, change it to a dry cloth to dry, and finally use an electric hair dryer to blow out the water in the gap

Camera Cleaning Method:

1. If the camera is wet, you can choose a lint-free soft cloth to dry and absorb the moisture of the camera as much as possible, and then use a brush or dry cloth to clean up the dust and dirt.

2. Use the camera's clean image sensor function, modern DSLR or good camera equipment has a clean image sensor function, which can shake off dust and hair through vibration sensors or filters. When using this feature, it can temporarily and effectively solve the smudge problem during photography.

3. Generally speaking, do not clean the camera in a dirty environment, and when it is finished, the camera may be dirtier than at the beginning. Please do not clean when the air contains a lot of dust, and if possible, you can choose an air freshener.

4. Don't blow on the sensor, find a blow specially designed for camera cleaning to deal with dust.

5. When cleaning the camera, in addition to cleaning the sensor and the front part of the lens, remember to take special care of those places that are hidden deeply, similar to the back of the lens, the mirror and the viewfinder.

6. Use the cotton swab correctly, you can use a cotton swab with detergent to clean the sensor, and remember not to touch the surface of the sensor with your fingers when using the cotton swab to clean the camera, because the grease on the fingers will also be transferred to the sensor.

After my introduction, I believe you have also come to clean up the 5 taboos that exist in the camera. Tell me how many you won?

Taboo 1: n wrong uses of lens paper

Every time there is dust or other dirty things, I do not hesitate to tear off a piece of lens paper and boldly carry out a large cleaning campaign. In fact, this is a big mistake, because the dust particles can rub against the surface of the lens and cause scratches. The right approach should be:

1. Tear off a piece of lens paper.

2. Roll the torn lens paper into a cylinder.

3. Pull both ends of the paper tube vigorously and tear it into two sections. You will find that there are a lot of hairs in the fractures and big files, and these hairs are the true face of the lens paper.

4. Use an air blower to blow off the floating dust, and then use the hairy end of the lens paper to gently wipe outward in a spiral from the middle of the lens.

The correct grip of the air blow

After the painful lesson of the last time, I have learned a new **: air blowing.

Taboo 2: Abuse of lens water

Taboo 3: The correct grip of the air blowing (don't pinch with two fingers anymore).

The air blower can blow not only the dust on the lens, but also the inside of the body. Although the possibility of dust getting into the camera is very small without changing the lens, you should turn the camera lens mount upside down and then blow gently.

Taboo 4: The selection and use of imitation lens water

The use of high-tech ** is summarized as follows:

1. Buy a bottle of lens water with guaranteed quality, such as this one.

2. Prepare a piece of RMB with a denomination of one yuan, and go to a nearby pharmacy to buy a large pack of absorbent cotton, such as this one.

3. Use small cotton balls to make a slightly larger cotton cake, and then make another one, how many are you made in total?

4. Use one of the pieces to dip a little lens water in the lens first, and gently wipe it from the middle of the lens to the spiral outward; Then quickly do the same with another piece to dry the shot.

5. Finish wiping and cleaning.

Taboo 5: The coating on the lens is very delicate

With a little dust, it is thoroughly cleaned, and all kinds of cleaning liquids are directly greeted on the lens. In fact, this is very dangerous, because the current lenses are coated, and lens water is often used, which will slowly wash off the coating, and the image imaging effect. In addition, if you accidentally get dust when drying, your previous efforts will be wasted.

So, don't use lens water until you have to.

Clean the lens contacts and here's how to fix it:

1. Remove the camera lens to observe the dirt.

2. If there is no dirt, you can wipe it clean directly with a lens cloth.

3. If there is dirt, you can first spray alcohol with a paper towel to wipe off the dirt, and then wipe the contacts with a lens cloth.

4. Because the lens is fully electronically controlled, it must be wiped dry to avoid short circuits, and the lens can be connected.

Precautions for camera care:

1. Moisture prevention is the most important.

If the humidity is too large, the lens is easy to mold, the southern climate is hot, the lens is extremely easy to mold, there is a saying that there are ten heads and nine molds, it is not an exaggeration at all, the air in the north is dry, relatively speaking, it is better. Many people think that just put the lens in a drying oven and use desiccant to remove moisture, but in fact, this is not the best way. The best way is not to wrap the lens too tightly.

The best way to prevent the lens from becoming moldy is to keep it in a ventilated environment to allow the lens to dry and dry before storing it in a drying oven.

2. Pay attention to waterproofing.

Water entering the lens is as harmful as water vapor entering the lens, and it must be cleaned up in time, as it will definitely become moldy over time, and it will also cause a short circuit in the electronic part. Especially when it rains, we should pay more attention to waterproofing, and now digital lenses are equipped with circuits, and the control of anti-shake function and ultrasonic focus automatic aperture change can only be achieved by relying on circuits, and you can't risk shooting, otherwise it may cause the lens to be scrapped.

3. Prevent vibration.

Preventing vibration is a critical issue. There are many tracks in the lens, and the vibration is easy to cause the screws to loosen, and as long as it is protruding a little, it will affect the rotation of the lens, and the lens cannot be focused. Although some lens screws have been fixed with glue, they will still loosen in the case of prolonged vibration.

When many people go out to shoot, the lens is taken or put in the camera bag, due to the long-term bump of the car, the screw protrusion, resulting in the lens can not be rotated, and the focus can not be carried out. <>