How to correct the level of the punch, how to prove whether the punch is normal, how to write

Use a frame-type spirit level to place on the worktop and level the machine by adjusting the horn blocks at the four corners. Generally speaking, the left and right sides should be the same height, and the front should be a little higher than the back.

Buy a frame-type level level, and screw the anchor screws down at the low point.

Frame level, adjustable horn adjustment.

You look for the mold directly, if the material correction is to buy the leveling machine Shanghai Youyi is good, if the punch body, there is the original manufacturer best ask the original manufacturer if not, ask the mold can be.

How to prove whether the punch is normal and how to write it?

How to prove whether the punch is normal and how to write it? Hello dear, how to check whether the operation of the high-speed punch device is normal: (1) Check the smoothness of each part of the high-speed punch, and make the smooth electricity fully smooth; (2) Check whether the mold device is correct and reliable; (3) Check whether the compressed air pressure is within the range of the rules; (4) Check whether the switch button is active and reliable, and be sure to disconnect the flywheel and clutch before opening the motor; (5) Make the press carry out several idle strokes, check the operation status of the brake, clutch and operating part; (6) Check whether the main motor of the high-speed punch has abnormal heating, abnormal sensation, abnormal sound, etc.; (7) Use a manual oil pump to participate in lithium ester oil on the slider; (8) Check and adjust the gap of the feeder roller to the process; (9) Check and adhere to the oil volume of the lubricator to meet the requirements of the rules; (10) When the motor is running, check whether the direction of rotation of the flywheel is the same as that of the reversal symbol.

Jinwo servo] hope to help you. If my answer is helpful to you, please also give a thumbs up (in the lower left corner), look forward to your like, your efforts are very important to me, and your support is also the driving force for my progress. Finally, I wish you good health and a good mood!

1. The horizontal correction method of machine tool installation is to install oblique iron in the corner of the machine tool four leather pants, which is used to adjust the balance of the machine tool, and when the longitudinal horizontal adjustment, the level is placed on the core track of the machine tool with higher precision, and the same is true for the transverse, which is generally measured at the same time with two levels, which is more labor-saving.

2. The ruler is pure, first set a point for the machine tool, according to this point, to determine the line, according to the line to determine the surface, in this way, the ruler should be higher than the machine tool, in order to calibrate the data, the advantage of the frame level is that no matter how complex the shape, can pass the point, to achieve the horizontal measurement of the surface.

Summary. If the speed and setting of the punch press are different, the problem needs to be solved according to the specific situation. Here are some possible ways to deal with it:

Adjust the speed of the punch: If the speed of the punch is inconsistent with the setting, you can adjust the speed of the punch to conform to the setting, pay attention to adjust it according to the specific situation, and do not pursue the speed too much and affect the safety and product quality. Update and calibrate equipment:

If there is a constant deviation in the speed and setting of the punch press, it may be that the equipment needs to be updated or calibrated, and you can contact the equipment repair or modification professional to deal with it.

If the punch speed and setting are different, the problem needs to be solved according to the specific situation of the stupid chain. Here are some possible ways to do it: Adjust the speed of the punch:

If the speed of the punch is inconsistent with the setting, the speed of the punch can be adjusted appropriately to conform to the setting, pay attention to adjust it according to the specific situation, and do not pursue the speed too much and affect the safety and product quality. Update and calibrate the equipment: If there is a constant deviation in the speed and settings of the punch press, it may be that the equipment needs to be updated or calibrated, and you can contact the equipment repair or modification professional for processing.

Fellow, I really didn't understand, I can be more specific.

Understand the machining performance of the punch press: Different types of punch keys allow different working speeds and loads, and you can fundamentally solve the problem by understanding the performance and parameters of the punch press. Check the maintenance of the equipment:

Punch equipment needs regular maintenance to ensure the normal operation of the equipment. Checking the maintenance of the equipment can find out the problem of poor lighting bucket and formulate corresponding solutions.