How to install the vehicle reversing probe and how to install the reversing image camera

Installation steps: First, remove the power supply cable at the vehicle battery, and place the removed wire away from the electrodes to prevent the power supply from being accidentally connected.

Determine where to mount the on-board camera. Generally, there are two types:

One is installed in the position of the license plate lamp, this installation is relatively easy, just use the small screws provided in the camera accessories to fix the camera on the position of the license plate lamp. Through the adjustment of the iron plate or gasket in the fitting, the camera can achieve the best reversing angle.

The wiring of the camera penetrates into the car through the gap of the license plate light, and is connected with the power supply of the reversing light and the extension cable. This type of installation of the reversing camera is currently one of the more popular ones, with a more discreet appearance and easier installation.

The other is drilled installation, embedded in the inside of the bumper, which has the advantage of not having to drill holes in the metal parts behind the car. Because the bumper is plastic, the camera routing is also relatively easy.

Connect the power cord of the camera with the power cord of the rear rear-view lights.

Finally, restore the battery power, start the car, hang the reverse gear, and you can see the reversing image on the car display.

Note: It cannot be completely relied on by the reversing rearview system to reverse, but can only be regarded as an auxiliary tool for reversing.

Do not easily connect the power supply of the car electrical appliance directly to the car battery power supply, so as not to cause the power supply to be unstable.

It is generally installed on the rear bumper of the car, installed according to the size of the punch hole, and is linked to the reverse switch or reversing light, and the power supply can be turned on when reversing to indicate the distance between the obstacle in the blind spot and your car.

1. Remove the rear bumper (the screws are installed at the rear of the chassis).

2. Find the reversing radar probe and push it out from the inside of the bumper to push the reversing radar (remember not to drag hard).

3. It is also necessary to deal with the wire end and wire of the reversing radar. First use a rag to clean up the dust and dirt dates, and then cut the thread directly.

Generally, it is stuck in the hole on the bumper in the form of a buckle, find a flat head and change the cone with a cloth to wrap the head only a little bit to pry out directly and wrap it with cloth to protect the paint on the bumper.

If it is original, it is better to remove the bumper and take it from the inside, and the original one has a clip pinned to the outside, and it cannot be taken off the outside, which refers to a better car.

Domestic cars generally do not have a rigid skeleton inside, drive the car to the trench, and you can see it directly below.

Remove the rear bumper, and you can see the connected probe inside, which is best done by a maintenance worker, which is more complicated.

Reversing image camera Chang portrait can be said to be a very good parking assistance device, which can observe the situation behind the car in a more comprehensive way, then, many riders will install reversing radar on their cars through the later stage, so as to increase the safety factor of the whole vehicle. But when it comes to its installation steps, I believe there are still some friends who are not very clear, and then we will talk about how to install the reversing image camera.

Installation steps for the reversing camera

1. First of all, lead the power cord of the reversing camera to the car charger, and lead the wire connected to the camera from the rear seat to the rear of the car.

2. Then use a screwdriver to remove the decorative lining plate of the rear trunk box.

3. Then choose the best position for the installation of the reversing camera and fix it early, generally in the position of the license plate light.

4. Finally, it is enough to connect the cable of the camera directly to the positive pole of the tail light, and of course we have to restore all the disassembled parts.

Then, for some car cameras that need to be drilled, we had better hand it over to a professional worker to clean the pickpocket, after all, this is a very test installation process. Let's not talk about the problem of wiring, just the step of punching is very specialized, if the punching is not done well, it is likely to sink or fall. Therefore, if you want to install (drilling) the reversing image by yourself, it is recommended to think twice.

Many drivers will install reversing radar on their cars according to the middle and late stages, so as to improve the safety performance of the whole vehicle. But when it comes to its installation process, I firmly believe that there are also many friends who are not clear.

1. First lead the power plug of the reversing rearview camera to the car charger, and lead the wire connecting the camera from the rear seat to the rear tail.

2. Then use a screwdriver to remove the decorative design jaw of the rear tail box.

3. Select the best position for the steering camera to install and determine it, generally in the place of the license plate light.

4. In the end, immediately connect the camera line to the positive level of the rear taillight, and naturally we also need to restore all the disassembly and assembly components.

For some car interception cameras that must be drilled, we try to install it as much as possible or hand it over to professional management personnel, after all, this is very honed installation and processing technology.

Not to mention the phenomenon of wiring, the process of just opening the hole is very systematic, and if the hole is not well solved, it is likely to collapse or fall off the mold chain. Therefore, if you want to install (drill) your own reversing rear view, you should propose or think twice.

Millions of car purchase subsidies.

1. It is best to place the reversing camera in the middle above the license plate light. When reversing, the picture that appears in the image is still angled, and the car owner has the best field of vision.

2. Installation method. First of all, the power cord of the reversing camera is led to the stool to charge the vehicle, and the wire connected to the camera is absolutely led from the back seat to the rear of the car. Then use a screwdriver to remove the trim lining of the rear trunk.

The reversing camera is installed in the best position and fixed in place, generally in the position of the license plate light. Finally, we can connect the camera cable directly to the positive pole of the taillight, and of course we have to restore all the disassembled parts.