Where is the Omega aftermarket address? Where is the repair center?

Omega Aftermarket Center is located in Room 2204, 22nd Floor, Block B, China Resources Building, No. 6 Shandong Road, Shinan District, Qingdao City, Shandong Province.

1. Wear it normally and avoid vibration. Only the appropriate amount of activity can make it continue to be on the bar, and in general, when the wearer is less active, the watch may run slowly, which is normal. It is recommended that consumers rotate the handle 20-30 times when using it for the first time to ensure that the string moves normally.

In addition, although the watch is shockproof, it is easy to break the tip of the pendulum shaft or the journal of the wheel train when the external impact is strong, and it can also make the fast and slow hand vibrate and affect the time.

2. The watch is waterproof. Try not to take your watch to swim or wash clothes, and if it rains or gets wet, don't pull out the watch handle to adjust your watch at this time, but dry it immediately. Since the head of the watch handle is relatively protruding, it should be avoided as much as possible.

At the same time, it is also necessary to pay attention to the gap between the handle head and the case, too small will affect the operation, and too large will affect the waterproof performance, and it will also be unsightly.

3. Prevent magnetization. Although the watch is made of materials that are not easily magnetized, it is greatly affected by magnetic fields when walking, so please stay away from places with magnetic fields. Wear a Rolex mechanical watch normally, try to stay away from the magnetic field, try not to get wet, although the fully automatic mechanical watch has the performance of magnetic field and waterproof, but usually try to pay attention to it, the wearing time will be longer.

Dust that enters the dial of a watch is usually due to gradual penetration over long periods of wear. If only fine dust is entered, there is no need to clean it without affecting the appearance and use. However, if it is a certain length of dust such as hair or acrylic fibers that enters the dial of the watch, it is necessary to pay attention, because this dust is very likely to cause the movement to stop.

8th Floor, Fifth Street, Oriental Xintiandi, No. 1 East Chang'an Street, Dongcheng District.

It's dust before it leaves the factory;

The watch is not well closed, and usually water enters when it enters the dust. The ash on the dial does not come from the outside world, but is caused by internal wear.

It is the dust that enters during use.

Reason for the watch to go into dust:

1. The watch has not been maintained for a long time.

2. There is dust accumulation inside the watch (the watch needs to be maintained) 3. The watch has the phenomenon of dust entering the outside (waterproof testing is required), it is recommended to send it to the after-sales center for testing and repairing the watch! ）

Omega Watch After-Sales Service Center: 400-659-0877

When repairing an OMEGA watch, all the watch parts are disassembled, the movement is wiped with gasoline, and then the other parts of the watch are cleaned by professional equipment, and finally oiled and assembled. In addition to the parts inside the watch, it is also necessary to polish the case introduced by the watch when cleaning the watch. Because OMEGA watches are very demanding on technical parameters, cleaning your watch is a very delicate task, and professional cleaning usually takes 5 days to complete.

And after such a complex professional cleaning, old watches can generally be turned into new.

There are 30 repair centers. In Shanghai, the OMEGA repair centers are located at No. 23 East Nanjing Road, No. 108-109 Hongqiao Road, No. 2-88 West Nanjing Road, Building 1, and No. 478-492 Middle Huaihai Road. In the Beijing area, there are shops A201B at No. 1 East Chang'an Street, 106B & 107C on the first floor of No. 138 Wangfujing Street, and No. 40 Zhongguancun Street.

The official after-sales service centers of Omega watches in China are: Beijing, Shanghai, Guangzhou, Shenzhen, Hangzhou, Tianjin, Nanjing, Xiamen, Fuzhou, Qingdao, Nanchang, Taiyuan, Zhengzhou, Wuhan, Nanning, Changchun, Dalian, Shenyang, Xi'an, Chongqing, Guiyang, Kunming, Wenzhou, Shijiazhuang, Harbin, Inner Mongolia Autonomous Region, Jinan, Changsha, Wuxi, Ningbo.

Omega History:

In 2011, the OMEGA Co-Axial Chronograph Calibre 9300 9301 was introduced, with an innovative column chronograph mechanism that placed the 12-hour and 60-minute chronograph hands in the subdials at 3 o'clock. This arrangement of the hands is similar to that of the hour and minute hands on the main dial, making the reading of the elapsed time more intuitive and in line with people's reading habits.

In 2012, a new era of timekeeping technology began with the introduction of a new generation of OMEGA chronographs, with a quantum timer resolution of 1 microsecond (hundredth of a second). In 2013, the first highly anti-magnetic watch, the Seamaster Aqua Terra>15000 Gauss, was launched, powered by the Master Co-Axial movement. OMEGA's innovative use of non-ferromagnetic materials has enabled the movement to resist magnetic fields of up to 15,000 gauss, solving the problem of anti-magnetic fields that have plagued watchmaking for centuries.

In 2016, the first Master Chronometer certified Speedmaster was launched, powered by the self-winding mechanical calibre 9904, which features a longitudinal wheel mechanism and a co-axial escapement for even greater longevity.

Both the movement and the watch have been tested by the Master Chronometer certification procedure approved by the Swiss Federal Institute of Metrology (Metas). Resistant to magnetic fields of up to 15,000 gauss, the movement is equipped with a silicon hairspring and a moon phase complication. The timepiece is joined by six Co-Axial Master Chronometer movements, which are equally significant.

These movements are used in a wide range of OMEGA watch collections.

Summary. Hello, we are happy to serve you and give you the following answers: Omega official website repair center is located in Zurich, Switzerland, is a professional repair center under the Omega Group, with first-class maintenance equipment and technology, professional technicians, can provide the most professional maintenance services for Omega watches.

With state-of-the-art repair equipment, our repair center can provide the most professional repair services, including movement replacement, strap replacement, case replacement, crystal replacement, crown replacement, clasp replacement, etc., as well as cleaning, lubrication, adjustment and other services. Regular maintenance services are also available at our repair centers to ensure that your watch is functioning properly and that its accuracy and aesthetics are maintained.

Hello, we are happy to serve you and give you the following answers: Omega official website repair center is located in Zurich, Switzerland, is a professional repair center under the Omega Group, with first-class maintenance equipment and technology, professional technicians, can provide the most professional maintenance services for Omega watches. With state-of-the-art repair equipment, our repair center can provide the most professional repair services, including movement replacement, strap replacement, case replacement, crystal replacement, crown replacement, clasp replacement, etc., as well as cleaning, lubrication, adjustment and other services.

Regular maintenance services are also available at our repair centers to ensure that your watch is functioning properly and that its accuracy and aesthetics are maintained.

I'm still a little confused, can you be more detailed?

Hello, we are happy to serve you and give you the following answers: Omega official website repair center is located in Zurich, Switzerland, is a professional repair center under the Omega Group, with first-class maintenance equipment and technology, professional technicians, can provide the most professional maintenance services for Omega watches. With state-of-the-art repair equipment, our repair center can provide the most professional repair services, including movement replacement, strap replacement, case replacement, crystal replacement, crown replacement, clasp replacement, etc., as well as cleaning, lubrication, adjustment and other services.

Regular maintenance services are also available at our repair centers to ensure that your watch is functioning properly and that its accuracy and aesthetics are maintained.

Hello, I am glad to provide you with the following answers: Omega official website repair center is located in Zurich, Switzerland, is a professional Yanyan repair center under the Omega Group, with professional technicians and equipment, to provide the most professional repair services for Omega watches. With state-of-the-art equipment, our repair center can provide the most professional repair services, including strap replacement, crown replacement, case replacement, hand replacement, dial replacement, case replacement, watch movement replacement, etc.

Our workshops also offer regular maintenance services to ensure that your watch is in peak performance, as well as replacement of the watch movement to ensure that your watch continues to perform consistently.

Hello, we are happy to serve you and give you the following answer: Omega Repair Center is located in the United States and provides repair services worldwide. Problems can occur due to the complex construction of the OMEGA watch, improper use or damage, or due to environmental factors such as pollution, humidity, temperature, etc.

Workaround:1If the problem is caused by improper use or damage, you can try to repair it yourself, but be careful not to disassemble the case to avoid damaging the mechanical structure of the watch.

2.If the problem is caused by environmental factors, you can try to clean the surface, change the strap, replace the battery, etc., to ensure the proper operation of the watch. 3.

If none of the above methods can solve the problem, it is recommended to go to the Omega Repair Center to have a professional technician repair the bridge. Personal Tips:1

Try not to disassemble the case to avoid damaging the mechanism. 2.Try to avoid contact with contaminants to avoid damaging the surface.

3.Replace the battery regularly to ensure the proper functioning of the watch. 4.

Clean the surface regularly to ensure proper functioning of the table empty code. 5.If something goes wrong, you can go to our repair center and have it repaired by a professional technician.