After I connected the network cable routing host, I used the settings made by the host, and I don t

Is it to go online?

1. Look at the hardware connection, right?

The home network cable is connected to the WAN port of the router.

The network cable connecting the host to the router must be connected to the LAN port.

2. Look at the software settings, right?

Whether the IP address of the host NIC and the CIDR block of the route are set at the same time.

Look at the router settings, right?

Go to the router WAN settings and the account password and dialing method are correct.

After the above is set, the running status of the router is set to see if there is a connection!

1.First of all, check whether the connecting cable is plugged in correctly and plugged in.

2.Click "Start" in the lower left corner of the desktop to run, enter cmd, open a black window, enter ipconfig all in it This command is to check the IP address of the computer, and then enter ping This command is to test whether it is connected to the gateway, generally the gateway address is this, or , and then ping or the address, if it doesn't work.

Check the settings on the computer, that is, whether the IP address settings are correct, especially DNS, telecom to use backup is.

3.Finally, check whether the router configuration is correct, the router configuration data may be lost, basically these problems. If it doesn't work, it may be a problem with the cat and other equipment.

There are often problems with the route, first set the password again, check the line again, and then put it for a few days and can use it again, I prepared two routes that can't be replaced, and it's done.

The route does not have a password set.

Dear users, hello.

Hope the following can be helpful to you:

Correct connection: the cat connects to the router WAN port, and the LAN port connects to the computer

1. Open a web browser and type in the address bar.

Then press Enter.

2. In the login window that opens, enter the username "admin"; The password is also "admin"; Then click "OK" directly.

3. After entering the router setup interface, select "Setup Wizard" on the left, and then click "Next".

4. Select "PPPoE (ADSL Virtual Dialing)" and click to enter the next step.

5. Enter the telecom broadband in the "Internet access" pop-up on the page, enter the broadband Internet access password in the "Internet Password" and "Confirm Password", and then click to enter the next step.

6. Click "Done" and return to the home page to check whether the settings are correct. You can see that the router has successfully dialed in and obtained the IP address for Internet access, and you can try to access the Internet. If it still doesn't work, we recommend that you check whether your line and computer are normal.

China Telecom provides the best quality network communication services, at present, Anhui Telecom has a "Hi Bang Summer" broadband discount activities, 100 megabit broadband free use, ITV free to watch, everyone come together! It is recommended to inquire directly through the online business hall or physical business hall of Anhui Telecom.

The network cable can be connected directly to the computer to access the Internet, and the router does not respond, because the router you just bought needs to go through the initial setup before you can use it.

Here's how to set up your router:

1. One end of the network cable is connected to the LAN port of the router, and the other end is connected to the network port of the computer.

2. Open the browser and enter the router account number and password written on the router box or manual.

3. Point setting wizard.

Internet access: PPPoE

Internet ID and Internet Password: Enter the broadband account and password.

Click Next.

4. Wireless status: on.

SSID: Enter the name of the wireless device.

Channel: Select 9 (if connected to an Apple mobile device or Mac: select 11 or 13).

PSK Password: Enter the wireless password.

Other defaults are sufficient.

5. After the setting is completed, one end of the network cable is connected to the LAN port of the modem, and the other end is connected to the WAN port of the wireless router.

There is no problem with the network and the computer, it should be that there is a problem with the way your router sets up to access the Internet.

First of all, you need to confirm the nature of the broadband you have installed, and if you have an Internet account and password, then you need to choose the PPPoE Internet access method.

1. The bus of the broadband network is connected to the WAN port of the router, and the LAN port of the router is connected to the computer.

2. After starting the device, open the browser and enter it in the address bar to enter the wireless router settings interface. (If you can't get in, please look at the nameplate at the bottom of the router or the router instruction manual, the default settings of different models of routers are different.) ）

3. An account and password to log in to the router appear in the settings interface, enter the default account and password admin, or refer to the manual;

4. After successful login, select the interface of the setup wizard, which will automatically pop up by default;

5. After selecting the setup wizard, a window will pop up to explain that you can set the basic parameters of the router through the wizard, and click Next directly;

6. Set up step by step according to the setup wizard, select the Internet mode, usually ADSL users choose the first PPPoE, if you use other network service providers, select the following two according to the actual situation, if you don't know how to choose, directly select the first item to automatically select, convenient for novice operations, click next after selection;

7. Enter the account and password applied for from the network service provider, and go directly to the next step after the input is completed;

8. Set the wifi password, try to make the alphanumeric combination more complicated, and it is not easy to be rubbed off the network.

9. After entering correctly, it will prompt whether to restart the router, select Yes to confirm the restart of the router, and you can access the Internet normally after restarting the router.

If the broadband is directly connected to the desktop to access the Internet, you need to set up the Internet access mode in the WAN port settings of the router according to this Internet access mode.

I have used a lot of routers and cats, but the router needs to be set up, and the direct link anchor to the Internet is not needed? It's likely that it's a problem with your motherboard's integrated network card, if you can, you can try to install a network card, and you should be able to buy one for a dozen pieces.

You can also use the elimination method, through the network cable connected by the router, connect to other computers to try whether you can access the Internet, if you can, you can roughly judge that it is your computer's network card problem.

Because you have changed the system n times, it should not be a problem with the system, most of it should be the problem of your network card, and it is best to change the network card.

I have to admire you, such a computer, you can use it from 09 to now. Idols.

The network card does not need to be set up, it is recommended to buy a network card and install it (the PCI network card on the desktop is about more than 30).