What should I do, what s going on with the old disconnection?

Reason for disconnection: Data terminal ready) The temporary invalidation of the signal will cause the disconnection.

2.If your modem does not correctly distinguish between a true disconnection of the far modem and carrier loss caused by unexpected line interference, it can also cause a dropout.

3.If there is a call waiting function in the service, a call happens to come in when you are connected to the Internet, which will also cause the connection to drop.

4.Another common cause of wire disconnection is incompatibility between modem and modem.

5.Inherent defects in the line can also lead to wire breakage (e.g., extensions, serial connections, or noisy lines).

You said that someone pinged you, it was a virus attack, kill it, I used six kinds of antivirus software to kill it all, and some of them couldn't be killed at all.

I think your problem should be the fifth point ** line in the internal defects, re-check your home ** line, pay special attention to the joint part, cut a section and reconnect it.

IP changed to above.

Then call the telecom ** is not a good signal recently.

Find a service provider to check the network cable.

First of all, check whether the crystal plug of the network cable is loose, click on the computer, and then open the device manager, and find the network adaptation.

If the orchestration point is deactivated and restarted, it may be fine. If not, don't be angry!

Sit back and have a cup of tea.

It's a hot summer, the temperature is high, don't you feel hot? Devices (devices are: cats, routers, network switches, Hubble, computers, etc.) also feel hot and can't work; You may wish to refer to the following methods and adopt measures that you feel are acceptable to reduce the temperature of the working environment of the equipment.

A: Users who often surf the Internet for up to half a year should open the shell of the device after the power is off and clean up the dust in the device.

b: Place the equipment in a safe place for people, open the lid of the equipment, and use air convection to strengthen the contact surface with the air for natural heat dissipation;

c: Install a micro fan to the equipment to increase the convection of air and force heat dissipation;

D: If you are doing IT, I suggest that you install a heat sink on the heating part of the device after disconnecting the power supply.

e: After the equipment is disconnected from the power supply, use a 3mm drill bit to drill many holes up and down the equipment to strengthen the air convection flow and improve the heat dissipation conditions;

f: To ventilate and dry the equipment, it is best to make an insulating bracket to support the equipment for natural heat dissipation;

H: Let the adsl cat sync first: power off the cat and restart it.

i: The software settings are reasonable, so that 3 do not install: do not install informal software, do not install P2P (occupy resources) software, and do not install commonly used software. Turn off all unnecessary internet connections, such as Thunderbolt.

BT donkeys, etc.;

j: Optimize the network.

Personally, I recommend using some gadgets.

For example, Super Bunny, Optimizer or 360, etc.

K: At least one valid anti-virus software should be installed on your computer.

l: NIC problem: The NIC bandwidth is appropriate and the operation is stable.

As long as you do a good job in the above aspects, your failures will be eliminated;

Thank you for my answer!

Thank you: friend!

Problem Description]:

How to solve the computer network disconnection.

Cause Analysis]:

NIC working mode.

Easy Steps]:

Solution]:

Change the NIC mode.

Select the [Connection Speed and Duplex Mode] option of the NIC working mode in the [Advanced] tab, change the value on the right to [10Mbps] half-duplex, and then click [OK]. (Figure 3).

Figure 3: Problem description].

How to solve the computer network disconnection.

Cause Analysis]:

NIC working mode.

Easy Steps]:

Solution]:

Change the NIC mode.

Open Device Manager in turn, find the corresponding network card in Network Adapter on the right, double-click to open it, and select Advanced in the tab.