What is the reason why the HP F210 dash cam does not turn on

First, determine whether the machine is dead or not turned on.

Crash, not starting: Crash means that the machine does not start or does not respond when the machine starts up in the case of eliminating power supply problems, and stays in a certain state.

Not turning on is a situation in which the machine does not work or crashes when the machine is started, and the machine is confirmed to be still not turned on through the solution of the crash.

2. After confirming that it is not turned on, analyze the possible reasons for not turning on the machine, and give corresponding solutions.

Cause Analysis 1:

Confirm whether the machine can supply power normally, if the machine itself has no power, and the access line has no power, it will not be able to turn on.

Solution 1:

Charge the machine to see if it can be charged normally; If not, check whether the power cord is normal, check whether the car charging source indicator is working, and whether the charging indicator on the dash cam is working.

Cause Analysis 2:

This issue can also occur due to a mismatch between the on-board charger used and the voltage of the machine.

Workaround 2:

Please choose the correct car charger for charging, 5V machines should be charged with 5V, and 12V machines should be charged with 12V.

Cause Analysis 3:

Confirm whether it is turned on correctly, see that the boot button is not pressed in place, and the wrong button or the button is not pressed in place will not turn on.

Workaround 3:

Check whether the power button is pressed to take effect, generally when the power button of the dash cam is pressed, its working indicator will turn bright.

Cause Analysis 4:

Confirm that the machine uses a high-speed memory card of acceptable quality.

Solution 4:

Take out the SD card or TF card first, and press the power button to confirm whether it can be turned on. If the recorder starts up normally, then it is a problem with the card, and the next step is to format your card. Format the card and plug it in, if this is still the case, it is recommended that you replace a memory card.

Cause Analysis 5:

Other unknown reasons that are not confirmed.

Solution 5:

For other uncertain unknown reasons, please find the "reste" hole, poke the reset hole with something similar to a paper clip, and then press the power button again to see if the power is turned on.

3. If you have tried all of the above and still can't turn on, it may be a problem with the hardware of the machine, and you need to contact after-sales customer service to deal with it.

There are many reasons why it doesn't turn on:

1. If the program drops (operating system), the machine will not be able to be used normally, and it needs to be sent back to the manufacturer or let the manufacturer burn the software and program;

2. Connect the power supply and press the reset button on the machine to see if the machine cannot be turned on due to a crash;

3. Confirm whether the power supply is connected normally, and the voltage is within the range of 5V 1A, if it is higher than this voltage, it will cause the machine to burn up, and this situation will also occur;

4. Take out the card to see if it is caused by the problem of the memory card;

There are many reasons why it doesn't turn on:

1. If the program drops (operating system), the machine will not be able to be used normally, and it needs to be sent back to the manufacturer or let the manufacturer burn the software and program;

2. Connect the power supply and press the reset button on the machine to see if the machine cannot be turned on due to a crash;

3. Confirm whether the power supply is connected normally, and the voltage is within the range of 5V 1A, if it is higher than this voltage, it will cause the machine to burn up, and this situation will also occur;

4. Take out the card to see if it is caused by the problem of the memory card;

There is only a little bit of storage power in the dash cam, and the dash cam needs an external power supply, whether there is no power supply with a cigarette lighter, or whether the interface of the cigarette lighter is not in good contact.

The brand is not important, now the science and technology are developed, and the technical content of the Jiling Qingchun recorder is low, and there is no quality problem on the base ruler.

Choose with high definition.

The wide angle is greater than 170 degrees.

Dark-free night vision.

(1) Take out the SD card or TF card first, and press the power button to confirm whether it can be turned on.

2) If it still doesn't turn on, please find the "reste" hole, use a thin soft thing to reset the hole, and then press the power button to see if it starts up.

3) If the dash cam starts normally, it means that it is a problem with the memory card and the memory card needs to be formatted.

4) Insert the card after formatting, if there is still such a situation, it is recommended to replace a memory card, after replacing the memory card, the crash situation can generally be solved.

The dash cam is charged but the charging source indicator light is on but does not turn on, the reason may be that the car charger does not match.

Solution: Change the original car charger provided by the manufacturer.

If it takes too long, it can also be caused by software conflicts, inappropriate drivers, or system problems.

Note: If you restore the system or reinstall it, when installing drivers, patches, software and other things, it will affect the deletion of things that will affect this failure, whether there is a problem with the hardware, such as hard disk, memory, etc., whether the temperature of the CPU and other hardware is high, if it is caused by hardware problems, it is recommended to repair.

I think this should be a problem with the quality of the dash cam, if you buy a 360 dash cam, there should be no sudden appearance of the Zen school of this banquet attack bridge problem, 360 dash cam big brand quality, and cost-effective, as long as 299 yuan.

It may be that the battery is not good, the battery is very garbage, or it may be that the charging plug is not in good contact, and there is a screen-off function in the settings, that is, how long does it take to automatically turn off the screen, and the dash cam is still in working state.

It is possible that you have not set it up, and another is the fault of the machine itself, you can go to the after-sales service to take a look, and the professional will check it for you, or replace it.