How long can the phone be used after it gets into the water, and how long does it take for the phone

Updated on number 2024-04-18
10 answers
  1. Anonymous users2024-02-07

    If the phone gets into the water, as long as it is dealt with in time, it will be fine.

    How to get water into your phone:

    Remove your phone from the water, quickly dry the water on the surface of your phone, and remember not to try to turn it on. Many users will subconsciously press the power button after taking out the mobile phone to see if the mobile phone can still be turned on, which is very wrong, even if the mobile phone itself is not damaged, once turned on, it may cause the result of burning the motherboard.

    The correct way to deal with it is to quickly remove the battery after taking out the phone, regardless of whether the phone is turned on before it is dropped. Then throw a few times at the side with more openings on the phone (such as the data cable interface), or the side with a large gap, and throw out the water in the phone. Hold the phone when you throw it, otherwise if you throw the phone out, you can be ready to buy a new one directly.

    If you feel that the water in your phone is almost gone, don't try to turn it on. As long as the phone is flooded, you should wait at least 24 hours if you want to turn it on. All you have to do here is to deal with the water stains that remain in your phone.

    These water stains are usually left inside the phone, and if you try to turn it on, there is still a risk of burning the motherboard.

    After the mobile phone enters the water, use a hair dryer to dry the inside, this method is not impossible, but pay attention to the way of operation, the temperature of the wind blown by the hair dryer is still relatively high, which is basically equivalent to the heating of the mobile phone.

    At the most severe temperature, the closer to the tuyere, the higher the temperature, burned by the hair dryer.

    It's not impossible, so when blowing the phone, you must pay attention to the distance between the hair dryer outlet and the phone.

    farther away, so that the temperature of the wind blowing on the phone is close to the normal temperature. Remember not to blow the air vent of the hair dryer directly on the phone, too high a temperature is absolutely not good for the phone.

    Blow for a few minutes and stop for a while, and then continue to shake the phone, shake it a few times and continue to blow, last 3-5 times It's about the same, the time for the hair dryer to blow the phone should not be too long, 20 minutes is basically fine. After blowing the phone, you still can't try to turn on the phone, because at this time you don't know if there is water in the phone, and you still have to make another one for the sake of insurance, that is, to dry the phone.

    If the mobile phone is in water, you can put it in the rice, the reason is that the water absorption of the rice is relatively good, and the mobile phone buried in the rice can help to absorb all the remaining water droplets and water vapor inside the mobile phone.

    After all, it is only an emergency measure, and the water absorption effect is the same as that of a professional desiccant.

    There is still a gap between the drying box, and you can usually prepare some desiccant or drying box in case of emergency. In some of the goods that are usually bought, there will be some small packets of desiccant, these can be used, collect these small packets of desiccant, and then seal the soaked mobile phone with them, the effect is much better than burying it in rice.

  2. Anonymous users2024-02-06

    If you are using a vivo mobile phone, the liquid inlet treatment method of the mobile phone:

    1. Don't force it on, it is likely to cause a short circuit in the phone;

    2. Don't shake the phone hard;

    3. Don't heat up your phone;

    4. Blot the liquid on the mobile phone, you can use toilet paper and other tools to absorb the water in the gap of the mobile phone, and absorb the water in the mobile phone as much as possible. When absorbing water, try not to move your phone;

    5. Place the mobile phone in a ventilated and dry place, and let the excess moisture on the surface of the mobile phone air dry naturally;

    6. Bring your mobile phone to the vivo customer service center for processing, which is subject to the test of the service center;

    Customer service center address: Enter vivo official website vivo**app--my--outlet query or vivo official website web version--bottom of the bottom -- service support--service outlet inquiry--select the province and city to query the customer service center address. It is recommended to contact ** in advance before going to avoid empty running, plan the itinerary reasonably, and travel safely.

  3. Anonymous users2024-02-05

    If you are using a Huawei phone, we recommend that you do the following:

    1. Please try to place your phone in a dry and ventilated place and use a paper towel to blot the water stains on the surface of your phone.

    2. If the phone is turned on, press the power button to turn it off; If your phone is turned off, don't try to turn it on.

    3. Please take out the SIM card and microSD card.

    4. Take your phone to a Huawei customer service center as soon as possible to avoid unnecessary losses.

    Precautions: 1. Do not move or shake the mobile phone frequently after entering the water, so as to avoid the spread of moisture inside the mobile phone.

    2. Do not use a hair dryer to blow or bake at high temperature (including microwave heating) after entering the water, so as to avoid the liquid being blown into the inside of the mobile phone and damaging the mobile phone at high temperature.

    3. The mobile phone is composed of precision electronic components, and there is a potential risk after water ingress, so please keep the mobile phone turned off.

    4. If you don't have a backup data, there may be a risk of data loss during repair.

  4. Anonymous users2024-02-04

    One of my mobile phones has tried to get into the water, dried it with a hair dryer, and it can still be used for a long time, more than a year later!

  5. Anonymous users2024-02-03

    Start by taking a hair dryer and blowing it. Don't turn on the machine first, just wait for more than ten hours normally.

  6. Anonymous users2024-02-02

    After the mobile phone is flooded, as long as the water ingress is not serious and the internal motherboard is not damaged, it can be used normally, and it can be used until the mobile phone is broken.

  7. Anonymous users2024-02-01

    Summary. Good evening, dear, I'll help you solve this problem. The specific steps are as follows:

    1.As long as you turn on your phone, the phone is connected to the power and falls into the water for ten minutes, and the water will immediately enter the inside. After being fished out, the motherboard of the phone will definitely burn out.

    2.If it is soaked in water, the motherboard will be overgrown with mold after a week, and the capacitor and resistance will be damaged when it becomes moldy.

    3.The longer your phone is immersed in water, the more likely it is to be damaged. When a phone falls into water, the first thing to do is obviously to take it out of the water immediately, because the longer the phone stays in the water, the higher the risk of damage to the water.

    After taking out the phone, it should be turned off immediately (preferably with the battery removed) to avoid damage to the electronic components inside the body due to water ingress and short circuit.

    How long does it take for a mobile phone to break when it gets into water?

    Good evening, dear, I'll help you solve this problem. The specific steps are as follows:1

    As long as you turn on your phone, the phone is connected to the power and falls into the water for ten minutes, and the water will immediately enter the inside. After being fished out, the motherboard of the phone will definitely burn out. 2.

    If it is soaked in water, the motherboard will be overgrown with mold after a week, and the capacitor and resistance will be damaged when it becomes moldy. 3.The longer your phone is immersed in water, the more likely it is to be damaged.

    When a phone falls into water, the first thing to do is obviously to take it out of the water immediately, because the longer the phone stays in the water, the higher the risk of damage to the water. After taking out the phone, it should be turned off immediately (preferably with the battery removed) to avoid damage to the electronic components inside the body due to water ingress and short circuit.

    [Bixin] <>

  8. Anonymous users2024-01-31

    Hello dear, this question is answered by me, the mobile phone will generally break down within five hours if it enters the water, and it is dried with a hair dryer, why can it blow the motherboard? After the mobile phone enters the water in a small area,In fact, the water entering will not directly reach the inside of the motherboard,Although the headphone jack is large,But Unicom actually has a certain degree of sealing inside,It will not enter directly,Generally, the charging port is far away from the motherboard,Even if the water is broken, the charging board will be broken first,It will not affect the motherboard。 When we use a hair dryer to dry the phone shell, the water will evaporate into water vapor, and the water vapor will diffuse to the inside of the phone and spread to the motherboard of the mobile phone, so that the area of water entering the mobile phone becomes larger.

    The phone got into the water, but everything was still functioning normally. It is not possible to charge it, because some water may not penetrate the motherboard or circuitry, and if you rush to charge it, it will damage the machine or burn the machine. The line burned down.

    It is recommended that you get into the water of the machine and its normal also put it in the sun. A ventilated place or a hair dryer to dry for a few days. Wait until the water in the water is completely dry and evaporate, and then recharge it, so that it is safer.

    The most effective way to get water into your phone is to turn it off. Water is conductive, water into the motherboard of the power-on operation, it is easy to cause a short circuit of small components to burn out, after the shutdown of the mobile phone stopped running, it should save the phone's life. Disassembling the phone is the only way to clean up the internal moisture, disassembling the phone and then using a hot air blower to purge the motherboard, so that the water in the motherboard can completely evaporate.

    You can master the basic disassembly skills of the mobile phone according to the online tutorial, and the mobile phone should be disassembled and cleaned up as soon as possible after entering the water. Why can I blow the motherboard when I dry it with a hair dryer? After the mobile phone enters the water in a small area,In fact, the water entering will not directly reach the inside of the motherboard,Although the headphone jack is large,But Unicom actually has a certain degree of sealing inside,It will not enter directly,Generally, the charging port is far away from the motherboard,Even if the water is broken, the charging board will be broken first,It will not affect the motherboard。

    When we use a hair dryer to dry the phone shell, the water will evaporate into water vapor, and the water vapor will diffuse to the inside of the phone and spread to the motherboard of the mobile phone, so that the area of water entering the mobile phone becomes larger.

  9. Anonymous users2024-01-30

    Summary. How long does it take for a mobile phone to break when it gets into water? After the water machine is flooded, if the water inside the water machine is not cleaned up in time, more than 12 hours, it will cause corrosion to the electronic components inside the mobile phone, so if the mobile phone is flooded, go to the mobile phone repair point as soon as possible to clean it, there is still no problem.

    Do not use the mobile phone after it is flooded to prevent a short circuit caused by water ingress inside the mobile phone. Generally, as long as it is not more than a day, there is still no problem.

    How long does it take for a mobile phone to break when it gets into water?

    How long does it take for a mobile phone to break when it gets into water? After the water machine is flooded, if the water inside the water machine is not cleaned up in time, more than 12 hours, it will cause corrosion to the electronic components inside the mobile phone, so if the mobile phone is flooded, go to the mobile phone repair point as soon as possible to clean it, there is still no problem. Do not use the mobile phone after it is flooded to prevent a short circuit caused by water ingress inside the mobile phone.

    Generally, as long as it is not more than a day, there is still no problem.

    Then if you determine whether the phone is really watered.

    1. Automatic power on and off for no reason 2. LCD display is sometimes absent, the contrast display of the display screen is abnormal, and the screen is black. 3. The key is out of order, and the key is wrong. 4. The battery symbol keeps showing that it is charging.

    5. The earpiece has a murmur and shuts down. 6. The background light, button light and signal light will always be on. Therefore, if you suspect that a second-hand mobile phone may have entered the water, you may wish to check the above 6 aspects, in addition, if there is very little water, and there is no failure, it generally means that the water has not entered the inside of the mobile phone, so there is no big problem, and finally you can shake the mobile phone more vigorously to see if the mobile phone will be abnormal and so on.

    Is it water that appears on the phone with a little blue screen?

    Yes, dear. It took a long time for the phone to get into the water before I knew what would happen.

    1. Fall into clean water when the power is on; 2. Falling into non-corrosive liquids in the case of power failure; 3. Falling into non-clean water when the power is on, or falling into corrosive liquid or viscous liquid or other clean liquids regardless of whether the power is on or not. The first two cases have a good chance of being saved and there may be no sequelae, while the latter depends on luck. Of course, if you are unlucky, PPC will also be bad if you put it in your pocket.

    But everything is fine with the phone.

    The phone works fine, but only a little bit of water comes in, and it still comes out of the cup.

    It's fine, dear.

  10. Anonymous users2024-01-29

    Summary. If the phone falls into the water for about three minutes, then he is estimated to have been completely broken, if the phone is picked up the moment it falls into the water, then he can still rectify it, but it has been soaked for three minutes, and it is estimated that it also belongs to the peace of the mobile phone.

    If the phone falls into the water for about three minutes, then he is estimated to have completely broken the shed socks, if the phone falls into the water at the moment it is scooped up, then he can still start to rectify it, but it has already soaked in the three-point chain next to the clock, and it is estimated that it also belongs to the peace of this mobile phone.

    You look at the next handful.

    If you don't have time to stay in time, the mobile phone will definitely be broken, more than 10 seconds or more in the water as soon as possible, the software of the mobile phone will enter the water, and then you can use the bracelet, so that the mobile phone is basically scrapped.

    You look at the next handful.

    If I go to a repair shop to disassemble and wipe my phone within one hour after it gets into the water, will this affect the subsequent use of the phone?

    Will it fail when you use it in the future?

    Definitely. After repairing, if it doesn't break within a month, it won't break, right?

    Yes, dear. If it is broken, will it be repaired if you go to the after-sales service to replace the parts of the mobile phone?

    If it breaks, it will be repaired by replacing the parts.

    Will there be any impact if the phone is disassembled three times in a row?

    Aging parts.

    Can the mobile phone be used normally after being disassembled and wiped by a professional who has entered the water? Or do you need to shut it down for a few days?

    Half a day is fine.

Related questions
10 answers2024-04-18

Mobile phone service innovation expert Beebee has you covered: >>>More

11 answers2024-04-18

After the mobile phone gets into the water, first quickly take out the battery and SIM card, drop the water, wipe it clean and put it in a cool but not humid and ventilated place to air dry! (Be careful to make sure the inside of the machine is completely dry). >>>More

6 answers2024-04-18

1.The reason why this happens has a lot to do with the phone's own RAM memory. RAM stands for Random Access Memory, which is what we often call a memory module in a computer, and mobile phone RAM is the memory module of a mobile phone as the name suggests. >>>More

23 answers2024-04-18

If you use a vivo mobile phone, the liquid inlet treatment method of the mobile phone is as follows: >>>More

12 answers2024-04-18

Solution: 1. If the mobile phone is flooded, do not do any key operation on the mobile phone at this time, open the battery cover and take out the battery, ** card, and memory card. >>>More