Changhong washing machine wheel shaft disassembly, how to disassemble the washing machine wheel shaf

Remove the screws and spacers - press down on one side of the wave wheel - release the wave wheel, pinch the ends of the laces with both hands and tighten them - gently upward - close the spacer.

Specific steps: 1. Cut off the power supply! The washing machine was dismantled in situ, as power and drainage were also needed later.

Use a screwdriver to loosen the screw counterclockwise, remove it, and lift the raised blade up with both hands. If there is water that is slippery, it is easy to dry it and lift it again.

2. After the blade is removed, there are 4 screws here, I can use a screwdriver to unscrew it, most of them need a wrench to unscrew, if there is a hex wrench of the same size, it is simpler.

3. The upper cover cannot be completely removed because there are water pipes and wires connected, and we should not mess with these wires, just keep it in this state. At this time, you will find that there is a lid on the barrel, unscrew 4 screws, lift 4 small buckles, and easily remove it.

4. If you unscrew the 4 screws under the blade in front, shake the inner barrel at this time, and put the inner barrel out, we usually see the inner wall of the inner barrel, thinking it is very clean, but in fact, the outer wall is very dirty, and the bottom!

5. The entire axle is removed.

1. First of all, unplug the power of the washing machine to avoid electric shock.

2. Remove the front cover of the washing machine, remove the control panel of the washing machine, and remove the screws on the control panel of the washing machine.

3. Remove the control panel of the washing machine, remove the screws on the control panel of the washing machine, and remove the controller on the control panel of the washing machine.

4. Remove the controller of the washing machine, remove the screws on the controller of the washing machine, and remove the wave wheel shaft on the controller of the washing machine.

5. Remove the wave shaft of the washing machine, remove the screws on the wave shaft of the washing machine, and remove the bearing on the wave shaft of the washing machine.

6. Remove the bearing of the washing machine, remove the screws on the bearing of the washing machine, and remove the wave wheel shaft on the bearing of the washing machine.

7. Remove the wave shaft of the washing machine, remove the screws on the orange wheel shaft of the washing machine, and remove the bearing on the roller shaft of the washing machine.

8. Remove the bearing of the washing machine, remove the screws on the bearing of the washing machine, and remove the wave wheel shaft on the bearing of the washing machine.

9. Finally, remove the wave wheel shaft of the washing machine to complete the disassembly.

To disassemble the washing machine wheel shaft, you need to first unplug the power plug, then remove the housing and panel, remove the parts such as the wheel and bearings in turn, and finally clean and replace the parts that need to be repaired or replaced.

1. First of all, we must prepare the tools, cleaning fluid and lubricating fluid brands that need to be used, and then pull out the power plug to avoid accidents such as electric shock during the dismantling process.

2. According to the model and structure diagram of the washing machine, gradually disassemble the shell, dashboard and other parts, and then disassemble the important parts such as the wave wheel and bearing, and use special tools or tightening tools to disassemble the parts.

3. In the process of dismantling, it is necessary to pay attention to the placement and operation sequence of the parts to avoid damage and dislocation during disassembly or installation, and at the same time, it is also necessary to regularly clean the parts and apply lubricant to keep the parts in good condition.

Expand your knowledge: In order to ensure the effectiveness and longevity of the washing machine, the following should be paid attention to in use and maintenance:

Avoid mixing different types of laundry, use detergents and softeners in moderation, wash the roller and filter regularly, and check and repair the washing machine regularly. It is recommended to choose washing machines from well-known brands and professional manufacturers to ensure the quality of use.

The steps to disassemble the washing machine shaft are as follows:

Turn off the power of the washing machine and turn off the water inlet and drain the messy side water pipes.

Open the panel on the outside of the washing machine. Different washing machine panels can be opened differently, often requiring the use of screwdrivers and other tools.

Disassemble the lower bearing or rotor disc. This is usually done by simply pulling the buckle open, or by gently tapping the top of the boggling shaft to retract it.

Remove the wave axle. Slowly pull the wave shaft upwards and then gradually pull it out. Proper twisting and shaking may be required.

Clean the wave shaft. If there is dirt on the wave shaft, it can be cleaned with detergent and brushes.

Replace or reinstall the roller axle cover. In case it needs to be replaced, you can take the old wave axle to a specialist electronics store and buy a new one, and then reassemble it in reverse order.

Inspect and test the wave shaft. After reinstalling the wave shaft, you need to test whether it is working properly. The washing machine can be turned on and a simple test can be carried out to check whether the overall condition of the rubber wheel axle is normal.

It should be noted that care should be taken when disassembling the washing machine to prevent damage to other parts, and if you are unsure of the operation needs, you can seek professional help.

Kiss, <>

We're glad to answer your questions! Changhong washing machine belt needs to be disconnected and unplugged before changing the belt. The O-belt button in the fan blade belt groove is bent a little away from the groove deviation, and then press the belt and pull the corresponding direction of the fan blade to rotate, so that the O-belt is completely clutched The conveyor belt of the fan blade leather groove expansion data washing machine usually uses a V-wedge belt, when you go, you can use a screwdriver around you to insert it between the large pulley and the belt, during the rotation process, make a little force to pin outward, turn the large pulley half a circle of the pulley will slide off.

When installing, the belt is sleeved on the motor pulley, and the belt is guided to the large pulley, due to the tension of the belt, the belt part will leak on the outside of the large pulley, at this time, the slotted screwdriver is inserted into the belt is not buckled, and the large pulley belt will be replaced. Stay safe. Hope mine can help you!

1. Prepare the tools first prepare the tools needed to replace the belt, including: new belts, screwdrivers, screw cones, screwdrivers, etc. 2. Disassemble the washing machine and unplug the washing machine from the power supply, then unscrew the screws on the washing machine, remove the cover plate on the washing machine, observe the internal structure of the washing machine, and find the pulley.

3. Replace the belt and remove the original belt from the pulley of the washing machine, then put the new belt on the pulley, tighten the screws of the pulley, and ensure the fastness of the belt. 4. Install the cover plate to install the cover plate of the washing machine back in place, tighten the screws, and finally insert the power plug of the washing machine into the power socket to complete the replacement of the washing machine's laughing and waxing belt.

Hello, glad to answer for you, 1Disassemble the Changhong automatic washing machine clutch assembly: (1) disconnect the power supply of the washing machine first; (2) Unfasten the screws on the clutch heat sink; (3) Disconnect the electromagnetic motor from the inside of the washing machine; (4) Pull out the electromagnetic motor and gently open the concentric shaft; (5) Remove the clutch and bellows; (6) Disconnect the power of the washing machine; (7) Disassemble the clutch or the corrugated pipe completely, and then reinstall the new clutch.

Expansion: In addition, before installing a new clutch, the connection of the washing machine circuit, motor and related components should also be checked to ensure proper operation. After the installation is completed, the working effect of the clutch should also be tested, such as checking whether the water level of the washing machine is good, whether the motor is running smoothly, etc., to ensure that the washing machine runs safely and reliably.

Hello, glad to answer for you. According to the above-mentioned rock digging situation: how to disassemble the clutch assembly of Changhong automatic washing machine.

A: 1Start by de-energizing the washing machine and turning off the faucets.

2.Open the door of the washing machine and remove the laundry from the inner drum. 3.

Remove the base screws of the washing machine with a wrench. 4.Remove the screws on the cover plate and remove the motor cover.

5.Remove the wires from the motor and remove the three belts. 6.

Remove the screws from the motor and remove the motor. 7.Remove the screws on the clutch cover and remove the clutch cover.

8.Remove the screws on the clutch and remove the clutch in a flash of burning. 9.

Remove the clutch assembly. Summary: Changhong automatic washing machine clutch assembly disassembly needs to be disassembled many times, and it needs to be operated carefully to avoid damage to the machine.

It is advisable to find a professional for repairs.

The inner cylinder of Changhong washing machine is disassembled as follows:

Step 1: Turn off the power and water sources.

Before disassembling, you need to turn off the power and water source of the washing machine, and for safety, it is best to turn off the main power switch and unplug the power cord. If it is a connected washing machine, you need to turn off the connected mode.

Step 2: Remove the water from the washing machine.

Before disassembling the inner drum, you need to remove all the water inside the washing machine. You can choose to use the dehydration function that comes with the washing machine to drain all the water inside, or tilt the washing machine to let the water out before disassembling it.

Step 3: Remove the shell.

Before disassembling the inner cylinder, you need to disassemble the shell of the washing machine, generally speaking, the shell needs to disassemble the control panel, pay attention not to pull the line of the control panel during the disassembly, otherwise it is easy to cause electrical failure.

Step 4: Disassemble the inner cylinder of the barricade.

Before disassembling the inner cylinder, you need to remove the springs and screws that hold the inner cylinder in place, and then use a tool to remove the inner cylinder from the washing machine mold. It should be noted that the integrity of the inner cylinder should be ensured during disassembly, and the force should not be too strong, otherwise it is easy to damage the inner cylinder or other components.

Step 5: Disassemble the bearing.

After disassembling the inner cylinder, you can see the bearing connecting the inner cylinder and the washing machine housing, you need to disassemble the bearing first, generally speaking, the bearing needs to use a special disassembly tool to disassemble, if there is no related tool, it is best not to disassemble the bearing by yourself.

Step 6: Clean the inner cylinder and bearing.

After disassembling the inner cylinder and bearings, they need to be cleaned, either with a washing machine-specific detergent, or with alcohol or water, and then left to dry.

Summary: To disassemble the inner cylinder of Changhong washing machine, you need to turn off the power and water source first, disassemble the shell, disassemble the inner cylinder and bearing, and finally clean the inner cylinder and bearing. Care needs to be taken during disassembly to avoid damaging other parts of the washing machine.

For people who don't know how to disassemble electrical appliances, it's best to ask a professional to help with disassembly repairs.