What is the reason why the landscape sound only rings in the front left and the front right?

It should be that the audio cable is not connected to the line is white, only one side rings, there should be no computer problems, but there is a letter on one of them, which is the red one without the letter black.

The reason why Sanshui Audio only has the front left and front right sounds is because his disc originally has these two channels. This is normal.

If the landscape sound only rings in the front left front and right sounds, it may be the connection line behind you, and the data connection cable has not connected it well.

The speaker only has the front left front and the right speaker, like this case, it is caused by cost savings.

Nowadays, it is already very good to have two speakers on the left and right for this impression, and the quality is also very good.

This is actually very simple to understand, because only those two places have horns, and the rest of the place has no horns.

The specific situation is good on site, and the operation is not difficult, so it is difficult to say clearly.

If the landscape sound is only made by the left and front speakers, it should be that the line is not connected, and you need to check the line.

If there is only a sound in the front, left, front and right, it should be that you have not adjusted it well, it should be stereo and there is a sound in all directions.

This is because there is a problem with the line connection.

This is the most common impression configuration.

It should be that there is a problem with the speaker of the speaker itself, and you can find after-sales personnel to check and repair it.

Landscape audio only money left front and think about the reason, is the sound broken or not adjusted.

Shanshui sound only before the left front right sound and the reason to consult the sales staff of the audio equipment.

Landscape audio, only the front right front left ring, you wiring wrong.

This should be that as long as you keep influencing and wanting to influence like this, you also want to have the impression that this is the case, and the impression will be opposite to him.

This impact is only due to the fact that there is more money and more money to verify and write-off, and you should pay attention to some news of the influence, or go to the place of influence professionally to take a look.

The landscape sound only rings in the front, left, front and right, because the sound is broken.

The landscape sound only rings in the front, left, front, and right, because of the problem of the position to look at the position.

Maybe it's because you haven't adjusted it well, so you try to readjust it.

The lines are all messy white, but one of the chains is a letter on it, which is connected to the red There is no letter to connect the black, only one side rings, there should be no computer problems, it should be the audio line is not connected, or there is a problem with the line, it is recommended to rule it out one by one.

Connect the *** on the power amplifier, VCD, AUX only have sound on one side, and plug in the back audio source line to change it to a sound speaker.

Why don't you plug in the microphone and try it out?

If your left and right speakers can make sound, it means that the amplifier and horn are fine. Listening to your description, it should be that the input of your amplifier only has 1 audio signal, try a different audio cable.

The computer audio cable is generally a 1-point 2 audio cable. One end is connected to the computer host, and the other end is connected to the audio host with two red and white connectors.

Correct connection: The red and white two heads are connected to the audio in of the audio of the speaker, and the two interfaces are R and L

R is the right channel input and L is the left channel input.

If the lines are connected, turn on your computer's volume control icon and see if the slider for each graph is turned to the side, if each icon slider is in the middle.

If all of them are correct, I guess the audio cable is not working, go and change it, it's not a few dollars expensive, try another one.

That's the original sound delivery in your stereo burned, you just go to the repair shop to fix it. It's just a few bucks... I had this problem with my speaker a few days ago...

It's very simple,The computer is connected to the host speaker's cable at one end plugged into the notebook output (headphone there)The other end is a red and a white plug in audio input Check up and down,Color to color。 The other two holes are plugged into the speaker line, which is also color-to-color.

Red and white plug audio in red plug red plug white plug white yellow plug to the computer.

speaksPlug in the small speaker cable Put the insert R on the right side and insert L on the left

You don't ask questions, and you don't pronounce the speaker model in detail.

It should be that the audio cable is not working.

Double-click the volume control icon, which is the small speaker icon in the tray area in the lower right corner of the taskbar, pop up the volume management, check the balance of the main volume and the waveform, that is, the slider above the volume size, see if it is dragged aside, if so, drag back to the middle.

This slider is to control the balance of the left and right channels of the sound, and drag it to the left is the left channel (provided that the speaker is placed correctly, otherwise drag it to the left and the right has a sound, and the left does not sound, hehe) (some speakers also have left and right balance settings, English balance).

If it's not a problem with the setting, or the audio cable is short-circuited, you can find a cable to replace the test, hoping to solve your problem.

The volume potentiometer inside your portable regulator is broken. If you don't have tools at home, you can only take the speaker to a nearby home appliance repair shop to find a master to repair it, and the charge** is between 10 yuan and 20 yuan.

1. The fault you encounter is a common fault of traditional "mechanical way to adjust volume" such as "rotation" adjustment or "rolling" adjustment.

2. The main reason for the failure is that the service life of this kind of potentiometer that changes the resistance value through the contact between the contact and the resistance bar is too short.

The method of emergency repair is:

1. First of all, you must have at least a cross-shaped cone that can be used at home (also called a plum screwdriver, a small screwdriver, etc.), use it to disassemble the portable adjustment box, and then see if you can remove the black disc that can be rotated, if you can remove it, then use a medical alcohol disinfectant swab to gently wipe the exposed small parts (that is, the volume potentiometer), which causes your speaker not to sound. If it can't be disassembled, it is riveted and fixed as a whole, so you can only replace it with a new potentiometer after removing it with an electric soldering iron.

2. If you have strong hands-on ability, you can also directly short the volume input line of the controller and the output line, abolish the function of the small volume potentiometer, and only use the volume adjustment behind the speaker or adjust the volume through the volume adjustment software of the computer in the future.

The stereo speaker is managed in the following way: a potentiometer tube is balanced, and it needs to be placed in the midpoint when listening to a program with a very well balanced signal, so that the sound pressure of the left and right channels is consistent, but sometimes when you feel that the left and right sounds are not satisfied, you can manually adjust it through this potentiometer. If this potentiometer is off-center, the left and right sides will be asymmetrical, and the right speaker will only sound when it reaches a certain position, and the 'left' speaker will be loud at this time.

Of course, the carbon resistance in the volume potentiometer will also wear out when the volume is often adjusted, so that the contact is not good, and when adjusting, it does not change the resistance value according to the original exponential but mutates, and there is also this [only when it reaches a specific position, the speaker on the right will sound] The situation occurs.

1、Tune the speakers on both sides,Is the year still the original non-ringing side is not ringing,The sound is still ringing,If this is the case,That proves that the speakers on both sides are no problem,It is the circuit inside the speaker that has a problem and sent it for repair。 If the original non-ring side rings, and the original sound does not ring, it is a matter of the speaker. Fix the speaker that doesn't make a sound.

2. Check whether there is a short circuit or open circuit in the speaker wiring over there, and then play the sound after processing it.

3. Detect the speaker that does not sound on the side, disassemble the speaker and measure it directly with a multimeter, dial the multimeter to the conduction block, and the red and black watch pens touch the two wires of the speaker in the speaker respectively to see if it is on, if it is through, it means that it is good, if it is not passed, it is bad, and it can not be repaired, so it can only be replaced with the same speaker.

The hand-wheeled volume potentiometer is in poor contact and needs to be replaced.

It is possible that the stereo is broken;

Check that the connection between the host and the speaker is divided into two,That is, the left and right channels (L, R),You can reverse the left and right channels,See if the sound of the channel is reversed,If it is reversed,That is, there is a problem with the host to the speaker connection cable or a problem with the computer settings。

If you reverse the left and right channel inputs or the original channel sounds, check whether your speaker has a balanced channel twist, if so, turn it to the middle, if not, it means that one of the speakers is broken.

The directivity is very good. Generally, the speaker composed of traditional speakers has poor directivity, and you must stand in front of the speaker to hear a more perfect sound, especially the treble part; And if you're standing on the side of the speaker, you may not be able to hear some background or accompaniment sounds; If you stand on the back of the speaker, maybe the sweet singing voice has become a voice that you don't want to appreciate. Flat speakers, on the other hand, do not have the above problems, no matter where you stand, you can enjoy the complete, real sound;

Sound attenuation is less. In traditional speakers, when you get too close, you will find that the sound is loud, and when you are a little farther away, you will feel that the sound is much quieter. Flat-panel speakers don't have the above problems, whether you are at close range or slightly farther away, there is not much difference in the volume of sound you hear;

The fidelity of the sound is high. Generally, the traditional horn, its shape is a sound cone, when it vibrates to produce sound, it often concentrates the sound in the larynx, compresses, and then transmits it, and the sound that people hear is the sound that has been compressed and deformed. Flat-panel speakers do not have the above problems, just because people used to listen to too much distorted sound, so once they come into contact with flat-panel speakers, they will feel that it is ordinary when they start listening, and then they are often deeply attracted by its natural performance;

Ultra-slim and takes up no space. Due to the special structure of the flat speaker, the speaker can be placed in any position, unlike traditional speakers, due to the different positions, the hearing effect is also very different.

Disassemble the knob adjuster, wipe it with alcohol (ordinary wine is also fine, preferably industrial alcohol) on the board near the knob, until the speaker has two channels of normal sound.

I don't know how it works, but that's how I fix my speakers.

It's the same as my stereo. I later found out that it was the internal relay that had poor contact.

The volume potentiometer is broken, the contact is not good, just replace it with a good one.

It may be something about the audio input line.

There is a sound or pitch setting in the settings, balance the tone, or there is no sound in the tune until the horn does not sound, or it does not sound, then check the line or horn.

Find someone who understands the sound and tune the channel.

It should be another one that is broken, just check it and see if there is electricity if it doesn't sound.

If it's not a problem with the wire, it's probably a problem with the amplifier!

If there is only one channel with sound, it means that there is a problem with your contact hole, you can try to listen to it more, debugging and solving.

The sound of the speaker's standard mode is adjusted within a mono setting.

Landscape sound has only one channel in standard mode,If there is a sound, you may not have turned on a fixed mode,Only turn on the single mode and that's it。