What happens if you add water to the side opening drum washing machine only once, and you will repor

Fully automatic with the washing machine, this situation should be the door of the washing machine closed is not easy to type. If the door is fine, it is caused by a faulty control circuit board of the washing machine.

If you add water to the side-opening drum washing machine only once, and it will report an error later, it may be that there is an error in the program of your washing machine, you have to turn off the washing machine, unplug the power supply, plug it back in, and restart it.

Studied, didn't use. Personally, I think the difference lies in three points:

The roller that opens the door is supported by two bearings, which is not sensitive to overweight clothing. In other words, the clothes are overweight, and the shaft of the washing machine is not easy to crush. It is equivalent to two people carrying clothes.

The side door is a one-sided bearing that is load-bearing, which is equivalent to a person holding clothes alone. Many families' drum washing machines are broken, they don't know how to use them, and when they wash, they put too many sweaters and cotton clothes, which are very heavy after absorbing water, and crush the unilateral bearing of the washing machine. Don't ask me why I know, my mother-in-law broke the washing machine twice like this.

In short, the bearing life of the drum washing machine with the upper door is much longer. The bearing is one of the fragile points of the current side-opening drum washing machine.

The drum washing machine with the upper door needs an opening in the drum and an additional mechanical control system. This is one of the bad points of the upper door drum washing machine. Improvements are needed in this area.

Opening the door up can save water and make it easier to add clothes on the way. The side door should not be opened casually in the middle of the door, otherwise the water will flow out. It is also not convenient to add water, for example, the wastewater from the water purifier can be used to wash clothes, but only the door can be poured with water.

: The working principle of the drum washing machine is different from that of the wave wheel, so it is definitely not enough to add water. What you encounter is a normal situation, all brands of rollers are the same.

Friends, I'm glad to answer your questions, add water to the side-opening drum washing machine, only add it once, and then it will report an error, which is generally caused by the problem of the motherboard or the intelligent detection system of the water inlet pipe.

Hope it helps!!

No, the water is dirty when you fill it up, so you will add water twice until it is clean.

Hello, this drum washing machine, you can set it up, it is fully automatic, so that it will not be wrong.

Set up the program, unblock the water pipes, and ask customer service.

Is it because he added water or the drainage system is set up incorrectly, or is the setting of his entire laundry program is such a setting, and then he has no way to add it?

Once you've added water, you'll need to use it with a single click, or after you click to activate it, otherwise it won't be used again.

The automatic washing machine is like this, add water once, and after washing for a while, the water is not enough, and it will be added automatically.

Hello, this drum washing machine only adds water once and doesn't add water, that's because you have set that water to that value.

If the water is added only once, then his procedure is still chaotic because his water is because its water is added many times.

Adding water means that there is no problem with the water inlet solenoid valve, the problem is on your circuit board, replace a main circuit board. It should be solved.

What is going on with the Kaimei rolling washing machine, the teaching machine, and the education department will not add it? It's all changed so cleverly in this case.

Peeking at the person who adds water to the drum washing machine only once and does not add it, it will report an error, which needs to be reprogrammed to the intelligent version.

In this case, you should consult the after-sales service!

The washing machine is added once and then it is not added, is there something wrong with it, should go to the maintenance master to take a look.

In this case, there should be a problem with your washing machine system, it should be a problem with the computer version, and it is best to contact the maintenance personnel to see.

The drainage threshold is not closed in place.

Caused by damage to the water level switch.

If the foreign body is stuck and the closure is not tight, it is necessary to disassemble the back cover of the washing machine, lay the washing machine flat, pull out the drain pipe, and check the solenoid valve.

The solenoid drain valve seal is deformed.

The electromagnetic threshold core is rusty and ineffective, or broken. Remove the electromagnetic threshold and polish the rusty threshold core with fine sandpaper.

The relays on the computer control board are sticky and cannot be released.

The water level switch is broken and needs to be replaced or repaired. The upper cover of the washing machine needs to be disassembled, turned over, and the lower water level switch is removed for inspection.

The water level pressure pipe is loose or cracked. The back cover of the washing machine needs to be disassembled, the washing machine is placed flat, and the transparent plastic pipe from the bottom of the bucket to the upper end is connected to the water level switch.

The water level switch is broken and needs to be replaced or repaired. The upper cover of the washing machine needs to be disassembled, turned over, and the lower water level switch is removed for inspection.

The washing machine is leaking while adding water, the reason should be that there is a problem with the drain valve of the washing machine, in this case, the washing machine cannot be used normally, because the injected water flows out, the water volume cannot reach the set water level height, the water level switch can not send an electrical signal, and the washing machine cannot operate.

If the drain valve is not closed or the drain valve is not closed tightly, water will flow out after filling and during normal use. It is necessary to check whether the drain valve core is reset, and check whether there are foreign objects or washing slag stuck in the drain valve body.

It is recommended to contact the after-sales service department of the washing machine according to the brand and model of the washing machine, and repair and inspect the drainage system of the washing machine or clean the drain valve.

1.Foreign body jamming leads to loose closing. The back cover of the washing machine needs to be disassembled, the washing machine should be placed flat, the drain pipe should be removed, and the solenoid valve should be checked.

2.The solenoid drain valve seal is deformed.

3.The electromagnetic threshold core rust activity is ineffective.

4.The relays on the computer control board are sticky and cannot be released.

You can contact the after-sales service for repair.

Either fix it or raise the drain.

Summary. Is it normal for Siemens front-loading washing machines to mix wash mode for 15 minutes without flooding? Why does the faucet logo light up when washing but there is no dripping sound Hello dear, 1. Check the faucet.

Nowadays, many automatic washing machines will not run once there is no water, and of course, a few washing machines will run without water. Generally speaking, if the automatic washing machine does not enter the water, the first thing to think about is whether there is a switch on the faucet of the automatic washing machine that is not turned on, if so, then just turn on the switch. There is also the case where the faucet switch is broken.

Is it normal for Siemens front-loading washing machines to mix wash mode for 15 minutes without flooding? Why does the faucet logo light up but not drip when washing?

Is it normal for Siemens front-loading washing machines to mix wash mode for 15 minutes without flooding? Why is the Shuizhou guess faucet logo bright when washing, but there is no dripping sound Hello dear, 1. Check the faucet. Nowadays, many automatic washing machines will not run or believe that once there is no water, the whole book of automatic washing machines will not run or believe, of course, a small number of washing machines will run without water.

Generally speaking, if the automatic washing machine does not enter the water, the first thing to think about is whether there is a switch on the faucet of the automatic washing machine that is not turned on, if so, then just turn on the switch. There is also the case where the faucet switch is broken. 2. The water pressure is too low.

Are you there? I just wanted to ask if it is normal for the mixed washing mode of the Siemens washing machine to not enter the water for 15 to 20 minutes.

I just want to ask Siemens washing cracked hail machine mixed washing mode fifteen to twenty minutes without water is normal, hello dear, 1, check with the slow check whether the faucet has been turned on. 2. Check if the water pressure is too low. 3. Check whether the water inlet is blocked by debris, it is recommended to check the water inlet and clean the water inlet filter.

4. After removing the inlet pipe joint of the washing machine at the end of the machine, turn on the faucet to check whether the water is normal. 5. Check whether there is any abnormality in the inlet valve. If so, replace it.