The Green freezer shows what the E0 is faulty

Problems with the temperature sensor.

Fault**e0 stands for "Refrigerator Freezer Temperature Sensor Failure".

1. Refrigerator failure**:

Machine alarm display E0: Refrigerator compartment freezer temperature sensor malfunction.

Two screens flashing e0: the refrigerator and freezer compartments are faulty at the same time.

Variable temperature zone alarm display e0: variable temperature chamber sensor fault.

Refrigeration Freezer Left Room Right Chamber Temperature Zone Shows E1: Refrigerator Chamber Evaporator Sensor Fault.

The temperature display of the refrigerator room is E2: the refrigerator sensor and the refrigerator cream sensor are faulty at the same time.

Second, other fault display and meaning.

1."Run" and "Alarm" lights flashing: mainly because the refrigeration system has failed, such as refrigerant leakage, ice, dirty blockage, etc.; There are also fan blades that are stuck or motor leads fall off and poor contact.

2."H" and "E" and "Alarm" lights flash: mainly for the temperature sensor to open circuit, short circuit or failure fault, where "E" is the refrigerator sensor failure; The "h" indicates that the sensor in the freezing or variable temperature chamber has failed.

3.The refrigerator compartment gear "high, low" flashes together with the "alarm": this is a malfunction of the refrigerator damper.

This refrigerator has an electric damper, which is driven by a stepper motor. Most of them are due to problems with the motor drive part; Then there is the failure of the switch in place, the signal is broken, or the line card is in poor contact; A few are defective motors.

4.The variable temperature setting "Refrigerated", "Slightly Frozen" and "Alarm" are flashing: this is due to a malfunction of the variable temperature damper.

5."L" and "alarm" flashing: This is because the temperature of the refrigerator is lower than zero, mainly because the damper is not closed tightly due to the deformation of the damper or other reasons, resulting in too much cold air entering the refrigerator.

6."Defrosting" and "Alarm" flashing: This is because the defrosting sensor is loose or in poor contact; Or it is caused by the incubator heater not working.

7."Blast Freezing" and "Alarm" flashing: This is caused by a broken fuse on the defrost heater.

8."Alarm" flashing: This is caused by the door light switch malfunctioning, or the door body is deformed and cannot reach the door light switch.

The refrigerator is equipped with a temperature sensor, we adjust the temperature control switch according to the room temperature and season, the refrigerator will slowly adjust to the set temperature, and the compressor of the refrigerator will judge whether the temperature is reached through the sensor, so as to choose to continue to run the refrigeration or shut down. Therefore, the thermostat of the refrigerator is very important, if the refrigerator shows e0, you should check the thermostat immediately.

Most refrigerators showing E0 are mainly a problem with the temperature sensor, we just need to replace it with a new one. If the variable temperature zone shows e0, it means that the sensor in the variable temperature zone is faulty, and the refrigeration and freezing display shows e0 instructions, and both are faulty.

In order to avoid such failures, it is necessary to pay a little attention during daily use and standardize the use of the refrigerator. For example, try not to put overheated food in the refrigerator immediately, it is recommended to cool it before putting it in the refrigerator. There's even a button for adjusting the temperature of the refrigerator.

When flash freezing is required, the gear can be turned up. The higher the gear, the lower the temperature. Clean the frost inside the refrigerator regularly so as not to affect the cooling effect of the refrigerator.

This situation indicates that the temperature sensor in the freezer layer of the refrigerator is faulty and the thermostat switch is broken.

How to check: If the refrigerator's thermostat is broken, it may not start (in other gears). You can turn the thermostat of your fridge to the highest, and if it can be activated, it is a proof that the thermostat is broken.

A broken thermostat can also cause non-stop. If the refrigerator is refrigerated normally and has not been turned off, the thermostat is broken and can be replaced. If the refrigerator has electricity (the light is on) but the compressor is not working, you need to measure whether the compressor has power or not.

If there is no power supply, the thermostat has no voltage output, you can judge that the thermostat is open, and replace the thermostat.

1. There are 0 5 or 0 7 gears on the refrigerator thermostat, of which 0 gear is the stop gear, 5 7 gears are the strong refrigeration gear, and the refrigerator compressor is not stopped in the forced cooling gear.

2. The higher the number on the refrigerator thermostat, the lower the temperature in the refrigerator. In spring and autumn, we usually set the thermostat to Variable 3.

3. In order to better achieve the purpose of food preservation and power saving, we can adjust the thermostat to 1 or 2 in summer and 4 or 5 in winter.

When a freezer has an E04 failure**, it usually indicates a failure in the temperature control system. This is because the freezer still seems to be trying to lower the temperature, even if it is already low enough, causing the freezer to cool down excessively. Therefore, resolving this fault requires you to inspect the circuit board on the freezer's control panel to check if it is damaged or burned.

If a faulty circuit board is found, it must be replaced, which usually requires a professional technician to be called in.

Another possible cause of E04 failure is the failure of the freezer compressor. If the freezer compressor is not working properly, it will not only cause problems with the temperature control system, but it will also cause the temperature inside the freezer to rise or decrease excessively. If you suspect that the compressor is faulty, you can try cleaning the compressor and condenser and checking that the circuit connections are stable.

In summary, the E04 failure** means that the freezer has a serious electrical or temperature control problem. Resolving this fault requires systematically eliminating all possible factors that may be problematic and having them inspected and repaired by a professional technician. Resolving this fault in time can ensure that the freezer is working properly and at the same time can also extend the life of the freezer.

E0 refers to a faulty circuit, either a poor contact, or a false solder there.