Why wait a few hours before opening a new fridge when you buy it

1. The newly purchased refrigerator is placed for a few hours before use, mainly considering that the refrigerator may be placed at an angle of more than 45 degrees during transportation and distribution, resulting in the refrigerant in the compressor flowing back to the refrigeration capillary and affecting the refrigeration effect.

2. After the refrigerator arrives at the destination after being transported flat, it should be erected and left for more than 2 hours before it can be powered on. In order to avoid that the refrigerant in the compressor will flow back to the refrigeration capillary when lying down and transporting, it will be blocked, which will seriously affect the refrigeration work of the refrigerator.

3. Precautions in the use of the refrigerator.

1. When using refrigerators in summer, pay attention to reducing the workload of the compressor. If the compressor starts for too long or too often, the compressor fuse will blow, and in severe cases, the compressor may be burned

2. Try not to place the refrigerator against the wall. It should be about 10 cm away from the wall and the top of the refrigerator should be at least 30 cm from the ceiling;

3. Before turning on the power of the refrigerator, check whether the voltage used by the refrigerator on the nameplate of the refrigerator is consistent with the voltage at home, and try to arrange a separate socket for the refrigerator, and do not use the same socket with other electrical appliances

4. When the refrigerator is working, the number of doors opened by the refrigerator should be reduced as much as possible to reduce the air-conditioning overflow of the refrigerator

5. When the power fluctuation is too large or the power is repeatedly cut off, the refrigerator should be suspended. Unplug the refrigerator to prevent damage to the refrigerator's compressor. During the power outage, the number of refrigerator doors should be reduced, which can effectively prolong the freshness time of food

6. The refrigerator cannot be used as a cooling device. Do not use the refrigerator to cool down, keep the refrigerator door open, let the cold air in the refrigerator run out, and reduce the indoor temperature, which seriously damages the compressor of the refrigerator and increases the workload of the refrigerator compressor

7. When adjusting the temperature of the thermostat of the refrigerator, the thermostat should be turned on in summer and the strong gear of the thermostat in winter, so as to reduce the power consumption of the refrigerator

8. The food in the refrigerator should not be placed too much. When placed, there should be a certain gap between the food and the food to facilitate the flow of cold air and accelerate the refrigeration and preservation of the food

9. Always clean the condenser and compressor of the refrigerator, and clean the dust of the box to facilitate the heat dissipation of the refrigerator

10. Defrost the freezer compartment of the refrigerator in time and clean the refrigerator compartment regularly

11. When placing food, try to cool the heated food thoroughly before putting it in the refrigerator to refrigerate or freeze

12. The inside of the refrigerator should be cleaned regularly. After using the refrigerator for a period of time, the inside will emit odors, so we need to clean the refrigerator regularly to remove the odor in the refrigerator.

The main consideration is to avoid the refrigerant in the compressor will be blocked by the reflux capillary when lying down and transporting, seriously affect the refrigeration work of the refrigerator, and the refrigerator may be placed at an angle of more than 45 degrees in transportation and distribution at the same time, resulting in the refrigerant in the compressor refluxing to the refrigeration capillary, and affect the phenomenon of refrigeration effect.

Precautions during the use of the refrigerator.

When using the refrigerator in summer, pay attention to reducing the workload of the compressor. If the compressor starts for too long or too often, the compressor fuse will blow, and in severe cases, the compressor may be burned

When the refrigerator is working, the number of refrigerator door openings should be reduced as much as possible to reduce the air-conditioning overflow of the refrigerator;

When the power fluctuation is too large or the power is repeatedly cut off, the refrigerator should be suspended. Unplug the refrigerator to prevent damage to the refrigerator's compressor. During the power outage, the number of refrigerator doors should be reduced, which can effectively prolong the freshness time of food

The refrigerator cannot be used as a cooling device. Do not use the refrigerator to cool down, keep the refrigerator door open, let the cold air in the refrigerator run out, and reduce the indoor temperature, which seriously damages the compressor of the refrigerator and increases the workload of the refrigerator compressor

The food in the refrigerator should not be placed too much. When placed, there should be a certain gap between the food and the food to facilitate the flow of cold air and accelerate the refrigeration and preservation of the food

Clean the condenser, compressor and dust of the refrigerator frequently to facilitate the heat dissipation of the refrigerator;

After the refrigerator is bought, it needs to stand for a period of time, but many people don't know much about how many hours of stationing. Why let it sit for a few hours before it can be opened?

1. The refrigerator should be stored for a few hours before it can be powered on.

After the refrigerator is bought, it needs to stand for at least two hours before it can be used with electricity, note that if the ambient temperature is low, the time needs to be longer. Because in the summer, if the lubricant inside is circulating and presents a liquid state, the standing time can be two or three hours is enough. However, if it is in winter, the internal lubricant may freeze and become solid, and the standing time should be extended, and it can be used with electricity after standing for about 6 hours.

2. Why should the new refrigerator sit for a few hours before it can be opened?

1. The reason why the refrigerator needs to stand for so long is mainly because of the bumps in the process of operation, if the bumps are more serious and there is a tilt, the lubricating oil in it will flow into the cylinder of the compressor. After buying, if it is put into use immediately, the lubricating oil will be hindered to a certain extent and will not be able to flow.

2. If the compressor wants to operate normally, it needs lubricating oil, but there is lubricating oil in the cylinder, which will affect the work of the compressor and seriously cause the refrigerator to be paralyzed. Therefore, it is necessary to let the lubricating oil stand for two or three hours before it can be used.

3. What problems need to be paid attention to when using the refrigerator.

1. In order to ensure that the service life of the refrigerator is prolonged, we should pay attention when using it, do not open the refrigerator frequently, otherwise the outdoor heat will enter the inside, which will lead to the problem of freezing on the inner wall of the refrigerator over time.

2. When using the refrigerator, you also need to pay attention to adjusting the refrigerator to the correct gear, the refrigerator is now more intelligent, so when you control it, you can set the appropriate temperature directly through the control panel.

The above content specifically introduces why the refrigerator needs to be placed for several hours after it is bought before it can be used with electricity, mainly considering that there is lubricating oil inside, if the lubricating oil is still in the cylinder, it will damage the refrigerator.

Because during the transportation of the refrigerator, due to vibration and a certain degree of inclination, the refrigeration oil on the compressor floor will be strung out, so to make the refrigeration oil flow back to the compressor base, it needs to be left for several hours to ensure that the compressor lubricating oil is good and avoid unnecessary wear and tear of the compressor.

After the lubricating oil in the pipeline enters the room, it will block the flow of refrigerant and affect the normal operation of the compressor. Severe consequences will cause the lubricating oil to hit the cylinder and paralyze the operation of the refrigerator. Therefore, please wait 2 to 3 hours after placing in the refrigerator for the lubricating oil to settle completely before using the power on.

After moving the refrigerator, the internal condensate needs to be returned to its place to avoid clogging of the refrigeration pipes. So it takes a few hours to turn on the electricity, and a few hours to put things in.

The refrigerator needs a buffer period, which can be slowly left for a few hours to allow the refrigeration oil in the refrigeration line to flow back into the compressor, and then power on to resume normal operation.

Because the previous refrigerator placement was to stabilize the gas inside, so that it was good for the refrigerator.

Newly purchased Hashimandarin refrigerators generally need to wait for a few hours before turning on the machine, because during transportation, handling and installation, the compressor in the refrigerator may be subjected to vibration and tilting, resulting in the lubricating oil and refrigerant inside the compressor mixing together, which will affect the cooling effect and service life of the refrigerator.

Therefore, it is recommended to leave the refrigerator for a few hours after installing it, let the lubricating oil and refrigerant inside settle, and then plug the power plug into the socket to turn on the refrigerator.

In addition, after opening the refrigerator, in order to ensure the refrigeration effect, it is best not to put a large amount of food into the refrigerator immediately, but wait for the inside of the refrigerator to cool down to a suitable temperature before putting the food into the refrigerator. This avoids a rise in the temperature inside the refrigerator, which affects the quality and storage time of the food.

Why wait a few hours to turn on a new fridge after you buy it? This is because the new refrigerator may tilt or invert during transportation, resulting in the loss of lubricating oil from the liquid combustion in the cavity of the compressed nano machine or mixed with the refrigerant, affecting the cooling effect and service life. As a result, new refrigerators need to be left on for a few hours before turning them on to allow their internal temperature to equilibrate and lubricating oil to redeposit to the lower part of the compressor to avoid damage to the compressor.

In addition, before opening a new refrigerator, it is necessary to wipe the inside and exterior clean to avoid odors and contamination that affect food safety.

The newly purchased refrigerator should be left to stand for 2 to 4 hours before turning it on. It is because the cooling system with a refrigerator contains lubricant, which shakes for a long time during transportation, causing the lubricating oil to flow into the basin pipe, and some will also enter the cylinder of the refrigeration compressor; In order for the lubricant to return to its position, the refrigerator needs to be laid flat for such a long time.

After buying a new refrigerator, you have to wait for a few hours before turning it on because there may be vibration or tilting during transportation, and the guide is careful not to cause the compressor oil to lose, and you need to wait for a period of time for the compressor oil to flow back to its original position. At the same time, the new refrigerator also needs to be pre-cooled and deodorized, which will take a certain amount of time. If Yanna is directly turned on, it may affect the performance and life of the refrigerator.

Therefore, it is recommended to wait for about 4-6 hours after installing the refrigerator before turning it on.

Because the new refrigerator has to be refrigerated from a very high ambient temperature to about minus 18 degrees, the temperature difference between the upper and lower temperatures is too large, and the working time of the compressor is relatively long. If you put a lot of food into the refrigerator at the same time, it will cause the compressor to overload for a long time, which will cause certain damage to the compressor.

Attached: Common sense of refrigerator use:

1. After the new refrigerator is purchased, it should be wiped several times with a clean rag, but do not close the door after wiping it clean, open the door to let the odor inside dissipate, or use an electric fan to blow it inside to speed up the emission of the odor, and then use electricity.

2. After the new refrigerator is carried back, it should be left to stand for a few hours before powering on the test.

3. The refrigerator should be placed in a cool and ventilated position, and a certain amount of space should be left around it to facilitate the ventilation and heat dissipation of the refrigerator and improve its refrigeration efficiency.

4. When the machine is powered on, the temperature setting of the freezer should be adjusted at minus 18 degrees, and the temperature of the refrigerated room should be about 5 degrees. The mechanical thermostat should adjust the size of the digital gear according to the ambient temperature of the season, adjust the smaller digital gear in summer, adjust the middle gear in spring and autumn, and adjust it in the larger digital gear in winter.

5. When the machine is powered on, do not put in the food first, wait for the temperature in the refrigerator to drop and stabilize, and then slowly put in the food after the compressor starts and stops normally, and do not put too much food at one time to avoid overload of the compressor.

6. The food placed in the refrigerator should be sealed and wrapped in a container or food bag to avoid odor caused by mutual odor.

7. If it is a direct-cooling refrigerator, when the frost thickness in the freezer exceeds 6 mm, it is necessary to manually defrost it in time to avoid reducing the refrigeration efficiency.

This is because the refrigerator will have bumps during transportation, which will make the liquid in the press unstable, and it may flow into the pipe, and it will be placed for more than 3 hours, so that the press will be stable, and the liquid flow will be pressed. Make the press work stably.

Let the new fridge refrigerate first, and then put things in later, if you put things in in advance, it cools very slowly.

Because you have to lower the temperature first, I'm really helping you look forward to it

Because the operation of the refrigerator compressor needs to be protected by lubricants, the manufacturer fills the refrigeration system with a certain amount of special lubricating oil during the production process, and the lubricating oil and refrigerant are completely enclosed in the refrigeration system after the refrigerator is completed.

During transportation, it can cause bumps, movement and even tilting, at which point the lubricating oil in the refrigerator will flow down the pipeline into the coil of the heat exchanger; A small amount of lubricating oil is also poured into the compression chamber of the compressor – the cylinder – under the action of jolting and vibration.

If the machine is started and running at this time, the flow of refrigerant will be directly affected due to the obstruction of lubricating oil in the pipeline; Second, because the function of the cylinder is to compress the gaseous refrigerant, if there is a certain amount of lubricating oil in the cylinder, it will affect the operation of the compressor, and it will cause liquid shock to completely break the cylinder, so that the refrigerator refrigeration system will be paralyzed. Even damage to the compressor.

Therefore, it is required to stand for 6 hours before turning on the power in order to return the coolant to its original state, so that the refrigerator can work at its best.

The refrigerator you just bought should be left to stand for 2 to 4 hours before turning it on to avoid oil circuit failure.

This is due to the fact that it is not guaranteed to be in a stable position for a long time during the transportation of the refrigerator, which may have passed a relatively long bumpy time and may even be tilted. At this time, the lubricating oil in the refrigerator will flow into the coil of the heat exchanger along the pipeline, and a small amount of lubricating oil will also be poured into the compression chamber of the compressor under the action of bumps and vibrations, so that the refrigerator will easily cause the refrigerator refrigeration system to be paralyzed after it is turned on.

Therefore, for the sake of insurance, after the arrival of the new refrigerator, it should be left for 2 to 4 hours before turning on the machine to avoid oil circuit failure.

Precautions. The running time of the newly purchased refrigerator should not be too long when it is used for the first time, and it should be carried out intermittently, giving each part of the refrigerator a run-in process, and then running in a small gear or setting the temperature slightly higher.

When the outside temperature is lower than 16 degrees, please turn on the compensation switch in winter, which is to help the refrigerator work. The winter compensation switch is usually located on the side of the thermostat.