Why does the rolling machine suddenly spark and can t turn on?

Suddenly, the rolling machine will burst into flames, and the flower will not be able to turn on, which may be due to the spark from the position of the space-based engine. It is best to check the spark plug at the engine to avoid a bigger crisis.

There are many reasons for this, and it may be that it takes too long to use it urgently, and this kind of cycle that occurs in the future will occur if the weather is relatively hot and the work is too long.

The reason why the rolling machine suddenly sparked and couldn't turn on the machine was because he had a short circuit in some places.

Personally, I think this may be the reason for some electricity, and then it won't be able to turn on, because of some problems with this month.

Maybe it's because the engine is broken, because when the engine is broken, it's easy to start fire.

If it fails, don't take it to repair, it's likely that the line will burn out.

Don't use it first, let a professional help you fix it and then use it later.

Why did the ** flower suddenly pop up and the machine couldn't be turned on? Then you wait for a while, don't turn it on right away.

If there is a sudden smoke and spark, then turn off the power or shut down immediately, otherwise the fire will spread.

It should be a short circuit, check the power supply, it is likely that the three wires are put together.

The spark indicates that the clerk inside or the spark plug is burning, so it will not catch fire.

Why does the rolling chicken suddenly spark and can't turn on the machine, it may be a malfunction, or uh, there is a short circuit, these symptoms,

If the high-pressure mouth is ignited, you will repair it, spend a piece of ocean to buy a high-pressure cap and circlip plus five pieces of ocean and a bag of 703 silicone you can do it yourself, if you can't repair it, immediately find a professional to repair it, otherwise it may damage the picture tube. Sometimes it is the breakdown of the high-voltage packet, and there will be sparks crackling behind the TV when the power is turned on.

It's more troublesome to repair! It costs about 100 just to open the lid. It should be that the diode of the electronic shade is broken. If you're not sure, you'd better find a friend who understands radio repair to help you analyze and solve the problem.

Something was burned. It is mainly caused by short circuits.

It should be a problem with high-pressure pumps, generally within 100.

You have to tell about the specifics.

According to the general experience, it should be that the connection between the monitor and the power supply is not good. Causes an electric shock.

In there should be attention to the grounding wire is good.

The spark is definitely the computer burned out, 100% confirmation that the power supply is damaged, there is a possibility that the motherboard is damaged, but it is unlikely.

If the power supply is on fire, it can be judged that the safety of the power supply is burned out for the following reasons:

1) Overload, the possibility of burning the power supply is extremely small, and the computer will run unstable and have frequent problems before the power supply is damaged, which will not cause the power supply to burn out.

2) Breakdown of high-power devices, this is the most likely, especially for older power supplies, the earlier power supply is too strict due to the input limit voltage (input voltage 220V), and we are relatively close to the substation or when the electricity consumption is low, the voltage will generally be relatively high, and this will often lead to power damage. Nowadays, almost all new power supplies are 220-240, or even 160-240, so this phenomenon is basically rare.

3) Electrostatic breakdown and short circuit of high-power devices. This phenomenon also exists in the shrinking power supply, the overvoltage protection inside is not done, the general low-end power supply is not, the power supply is left in the position, but in order to save costs, when our power switch ignition power supply is tested at this time.

It's usually a power supply, and there are no sparks anywhere else.

The chassis is broken and can no longer be used. Otherwise it will**.

1. Plug in the plug of the washing machine, cover the cover plate on the dehydration side, twist the knob, if there is a buzzing sound and the motor does not rotate, first open the rear cover plate to check whether the brake cable on the dehydration side is broken, if the stall caused by the breakage locking, reconnect the brake wire, adjust the clearance, and it can return to normal. 2. If the brake cable is normal and the buzzing sound is still there, it is time to check the capacitor of the dehydrator, or take a good replacement, the capacitor capacity specification is 6uf, and the original capacitor is damaged after the motor runs after replacement. 3. If the dehydration motor does not make a sound and does not rotate after power-on, first check the power supply of the dehydration motor with the AC 1000V gear of the multimeter, if there is a 220V power supply in place, it means that the motor is broken or burned, and the dehydration motor needs to be replaced.

4. If the dehydration motor does not have a 220 volt power supply, check whether the end cover is closed in place, whether the reset switch is flexible and damaged, and check whether the dehydration timer is damaged. 5. If it is damaged, replace it with a new product of the same specification, test the machine after replacement, and operate normally.

There was a spark under the washing machine and it didn't move. In this case, the reason should be that the electrical appliances inside the washing machine have an electrical short circuit, and the power should be unplugged immediately to stop using it.

It is recommended to contact the after-sales service department of the washing machine according to the model and brand of the washing machine, and ask professionals to carry out maintenance inspection and troubleshooting.

Check the circuit and motor in the washing machine and you will find the fault.

Dial the power or turn off the power switch, and then extinguish the fire, if not, forget it, and then release the water to contact the after-sales maintenance.

The motor or capacitor is burned.

The power supply is burned, so try it again.