Router masters, who will get a router? Let s teach the masters

First of all, according to your description, you said that the router dropped during the day and good night when you used it a few days ago, which means that there is no problem with your router settings, and you can dial up the Internet, and at the same time, the network operator in your area does not restrict the router. Also, I think the problem you mentioned is due to the settings of the router.

Solution:1. Please check that there is no problem with the physical connection of your local machine, don't laugh, many times it is caused by local problems. So this check is necessary! ~

2。Check the local connection: ping

3。Check the connection to the router: usually ping or 4. If all of the above is correct, please log in to the router and clone the MAC address of the machine to the router to prevent the carrier from binding your MAC address.

5。Restart your router and try dialing again. That should be no problem.

Hello! 1. How many computers do you currently have? Can I have direct access to broadband and dial-up Internet access?

2. What is the brand model of your router?

Hope it solves your problem, good luck!

You set it up like this:

Connect your router to a computer that you can dial normally with a direct connection to ADSL, log in, click "Network Parameters", click "MAC address clone", and then press the button to clone MAC address. Then check the WAN port settings, re-enter your account number and password in the PPPoe dial, enter it carefully to make sure there are no errors, and select Autoconnect below. Then save the settings.

Plug your ADSL into the WAN port of the router and try it again, okay?

Hello! Since there is a time when you can access the Internet through the router, then at least it proves that there is no problem at the entire hardware device level. Moreover, the protocols of the system and service layer used to be normal.

In this case, it is most likely caused by the server problem of the service provider, it is likely that the operator has set a routing policy on the server, or disabled the routing, and it is best to go to the business hall to find out the details for details. Above.

Start with the service of the network service provider**! Ask if it's a network problem! Call him to test it, and if it's fine! You're trying to change the cat and the line! Also, check your computer's network cable interface (try another computer to be clear)!

What region?

Some regions have restricted routing.

One is no problem with Internet access, which means that it is not a network problem.

This has nothing to do with the system. No need to redo.

You can hi me to discuss.

Turn on the DHCP function of the primary router, and then manually assign IP addresses to secondary routers A and B (require a brigade to contain an IP segment, for example: and, fill in the manually assigned IP addresses in the WAN port settings of A and B respectively (think of the router as a client device like a computer, you can understand, the router also needs an IP address like the client).

After the main router is set in this way, you can use the dynamic IP, if you need to use the static IP, you need to set it.

on the picture above.

The setting of your potato void is actually the IP error, which can be seen through your picture.

B and A are not in the same IP range.

The secondary AP is the second wireless router that you count as a few burns. The primary AP is your first wireless router.

The above is my setting, if not, please let me know.

Regardless of whether you can or cannot upload this picture, your IP is not right, that is, it is not A or B

The vice-ap doesn't know what that means.

I don't know if the route you are talking about is home or Cisco, Huawei, please elaborate.

2.It doesn't make much difference.

3.You're talking about **server Internet access, right? The server software or IE is set on the PC side.

4.Actually, the router works continuously. Not suitable for frequent switching.

The current shock when powering on is actually a killer that damages electrical appliances, of course, there is a ratio of working and idle time in the design of electrical appliances, and there are suitable for a short time and a long time. The router is a long-term work system, and you can turn it off when you don't need the network when you sleep at night. It also saves energy.

The Guardian anti-Trojan program can generally find the sending and receiving data of the abnormal process, which is related to the behavior of the process and the program, and has nothing to do with whether the screen is taken or the content of the data sent. Traffic monitoring can only see the rate of sending and receiving and the amount of traffic.

1 The more expensive the more powerful the function For example, a thousand pieces may support OSPF, but a hundred pieces will never be possible. Of course, a hundred yuan is enough for a family.

2 No impact.

3 Inside the browser's **Settings.

4 Frequent plugging and unplugging is large, because there is a current shock.

5 I can't see it. The data transmitted by the Trojan is the same as the normal data, and there is no difference between the traffic monitoring software. It can be protected with anti-virus and anti-Trojan software.

1. High load continuous operation.

2. No difference.

3. IE's ** settings are there.

4. No damage.

You can only see which process has data to send and receive.

1.Stability, transmission capacity.

2.Routing is powerful enough, no.

3.Routing (not guaranteed by network providers).

4.Plugged in all the time.

Is it a god horse? bs it's been a long time.

360 traffic monitoring and control is not visible. Because his data is too small.

TP routing is basically sufficient. However, it is recommended to buy a slightly better one. Generally around 140 is a good point.

There is no discount for delays. Just don't you have an external IP if you dial up? You ping your public IP address. Just know that the delay is only 1. No problem.

Article 4 is really hard to say, you have to ask it how it feels.

The router is nothing more than a matter of settings.

The specific connection and setup steps of the router tell you.

1. The bus of the broadband network is connected to the WAN port of the router, and the LAN port of the router is connected to the computer.

2. After starting the device, open the browser and enter it in the address bar to enter the wireless router settings interface. (If you can't get in, please look at the nameplate at the bottom of the router or the router instruction manual, the default settings of different models of routers are different.) ）

3. An account and password to log in to the router appear in the settings interface, enter the default account and password admin, or refer to the manual;

4. After successful login, select the interface of the setup wizard, which will automatically pop up by default;

5. After selecting the setup wizard, a window will pop up to explain that you can set the basic parameters of the router through the wizard, and click Next directly;

6. Set up step by step according to the setup wizard, select the Internet mode, usually ADSL users choose the first PPPoE, if you use other network service providers, select the following two according to the actual situation, if you don't know how to choose, directly select the first item to automatically select, convenient for novice operations, click next after selection;

7. Enter the password applied for from the network service provider, and go directly to the next step after the input is completed;

8. Set the wifi password, try to make the alphanumeric combination more complicated, and it is not easy to be rubbed off the network.

9. After entering correctly, it will prompt whether to restart the router, select Yes to confirm the restart of the router, and you can access the Internet normally after restarting the router.

How to set up a wireless router

Home Network Environment Cabling]:

1. There is a cat (modem): cat (modem) - router WAN port; The LAN port of the router --- a computer.

2. No modem: network cable --- router WAN port; The LAN port of the router --- a computer.

Computer enters the router]:

1. The computer IP and DNS settings are automatically obtained.

2. Open the browser, enter the general router address in the address bar is this or check the login information on the back of the router) Enter the route - enter the user name and password, (the default is generally admin).

Set Router Dialing]:

1. In the [Setup Wizard], select [PPPoE Dialing] (some are ADSL dialing), enter the username and password (provided by the network service provider) according to the prompts, and save.

2. In [Network Parameters] --WAN Settings], select [Normal Mode], and select [PPPoe Dialing] in the three options of [Connection]. The next step is to select [Auto Connect], Save, and Exit.

Turn on the router's wireless function].

1. Select Wireless Settings --- Basic Settings.

2. Check [Turn on wireless function] and click Save.

Set wifi password].

1. Wireless Settings - Wireless Security Settings - Select [WPA-PSK WPA2-PSK].

Authentication Type: Automatic.

Encryption algorithm: AES.

The PSK password is the wireless password. Set the required password.

What's wrong? What's the problem? If you don't say it, how can others help you?

It depends on the landlord's situation, if the landlord has a router, the wire that pulls you is from his router, the easiest way is to get a router, connect the LAN port of the router and the network card port of the computer with a network cable, open the computer, enter the login address address of the router in the browser address bar, generally or, you can check the sticker on the back of the router, enter the default login name and password to enter the router settings page, and turn off the DHCP function of the router, Set the wireless password and wireless signal name, save and restart the router, and insert the cable pulled by the landlord into the LAN port of the router (note that it is the LAN port, the router generally has four LAN ports), and it is generally OK at this time. (If you don't have wireless Internet access, you can buy a 4-port switch, which is more economical and convenient).

If the landlord doesn't use the Internet and doesn't use the router, then you have to ask the landlord what the Internet username and Internet password are, and then connect the LAN port and computer network port of the router, and connect the WAN port of the router with the cable pulled by the landlord, and also log in to the router settings page, select PPPoe working mode for the router working mode, enter the username and password provided by the landlord, save and restart, and it's OK.

In fact, it is explained in the router manual, which is relatively simple.

The LAN port of the router connects your two computers.

Is your wireless router TP-link? If you buy an extra power modem, you can access the Internet on two computers at the same time.