A socket can be plugged into two electrical appliances, and one of the three hole jacks is burned, c

Yes, as long as there is not too much on the line, if the outside insulation is also less, just change to a new one, if the insulating plastic is not burned, disassemble, see, the three holes are divided into zero wire, live wire, and ground wire, with a voltage tester to measure, generally less wiring, just connect on the line. It's very simple, give full play to the spirit of DIY, low-carbon life!!

Generally speaking, it can't be repaired, if you have to plug in two appliances, it's safer to replace it with a new one! If you only use the top two holes, you can make do with them.

You can fix it! The key is whether the socket board and the copper sheet inside are burned out, if not, then change the dot wire! If it's broken, you don't have to fix it, safety first!

Of course, it can be repaired, but if it is burned, the quality is not good, and the new one will not cost much. It is recommended to get a new one. Safety first.

The socket has burned out, and it is better to replace it with a new one. It is necessary to know that after the internal contact copper sheet of the socket is heated by high temperature, the copper sheet will be softened, and the elasticity will also decrease, and the poor contact, especially when the large current passes, the resistance on this contact point will continue to increase, resulting in hot heating, which will cause tripping, and even fire. For the safety of the home, the socket should be replaced with a new one.

Yes, just change the power cord.

You can fix one of the wires and burn it out, and you can use it when you connect it.

The seat has burned over, and it is better to replace it with a new one.

It's best that you change to a new one.

Kiss, hello, the first line of the plug-in board is closed with a smile, and a hole is burned, which is generally a file crack, which will not affect the use of electrical appliances on other jacks. But it's better to open it and check it out as well. Because, the jack of the socket is scorched, which is caused by three reasons.

The first reason is that the quality of the socket is too poor, marked with 10 (a) amps, but the cross-sectional area of the metal contact piece inside it is not enough due to cutting corners, or it is a copper-plated product; The second is that the current of the electrical appliance exceeds the rated current of the socket by a lot, resulting in the contact points being overheated and scorched. Generally, there are several household sockets such as 5 (A) ampere, 10A, etc., when using 10A sockets, the use of electrical appliances above kilowatts will cause the contact points to overheat and scorch the socket panel; The third case of lifting and closing is that the elasticity of the conductive copper sheet in the socket decreases, resulting in poor contact between the contact piece and the metal sheet of the plug; So you should open the cover and check if the contact piece inside the socket is thick enough? It can be calculated as 2 amps per square millimeter.

Use a file, saw blade and other metal to scratch the contact piece to see if it is a copper material; Move the contact pieces on both sides to the opposite side so that they are in contact with each other. This way things like this can be avoided.

Summary. Kiss! Hello, happy to answer your <>

Can a two-hole plug be used on a three-hole socket, the answer is as follows: it can't be plugged in, because of the big safety hazard.

First of all, the prong design of the two plugs is different, the prongs of the two-hole plug are generally in a parallel state, and the three-hole plug has an additional ground prong, and the two prongs below are not horizontal, so the two-hole plug cannot be used on the three-pin socket. If you have to use a two-pin plug in a three-prong position, it is advisable to purchase a new socket panel to avoid leaving hidden dangers. Additional Information:

The metal pieces of the two-pronged plugs should be broken at an angle to fit the angle of the two holes at the bottom of the triangle socket. Although the two-pin plug can be plugged into a triangular socket, it is strongly discouraged for safety reasons. Because of this use, the grounding function is lost, and it is extremely unsafe for the human body.

Hope mine can help you <>

Do you have any other questions?

Can a two-pin plug be used on a three-pin socket?

Kiss! Hello, happy to answer your <>

Can a two-hole plug be used on a three-hole socket, the answer is as follows: it can't be plugged in, because of the big safety hazard.

First of all, the prong design of the two plugs is different, the prongs of the two-hole plug are generally in a parallel state, and the three-hole plug has an additional ground prong, and the two prongs below are not horizontal, so the two-hole plug cannot be used on the three-pin socket. If you have to use a two-pin plug in a three-prong position, it is advisable to purchase a new socket panel to avoid leaving hidden dangers. Additional Information:

The metal pieces of the two-pronged plugs should be broken at an angle to fit the angle of the two holes at the bottom of the triangle socket. Although the two-pin plug can be plugged into a triangular socket, it is strongly discouraged for safety reasons. Because of this use, the grounding function is lost, and it is extremely unsafe for the human body.

Hope mine can help you <>

Do you have any other questions?

This kind of three-pin socket, can you plug in a two-pin plug, the plug is like this.

Please send us a text message

Pro-can, the three-hole socket can be plugged into a two-hole plug, the two-hole plug is generally not a big hidden danger to static electricity, it can be used with confidence, the circuit is in parallel, the voltage must be the same, of course enough. However, it is better not to plug in a two-pin socket than a three-pin plug; Electrical appliances are three-pin plugs, and the static electricity generated by the electrical appliances reaches a certain amount, which will cause electric shock to the human body. It is very useful to understand what switch is installed on the zero line, left zero right fire, red fire blue zero and other basic common sense.

It's okay, right, did you see the ** that was sent?

Okay thank you. Yes, dear

This can be straightened at both ends, can be plugged in, I have a lot of electrical appliances because the plug is crooked, simply plug in the three holes, but it is recommended not to do this, it is more dangerous, the three-hole socket is generally suitable for three-hole appliances, in order to prevent electric shock.

The three-pin plug has one more ground wire than the two-pin because of the large voltage, and the two-pin plug cannot be connected to the three-pin plug, otherwise it is easy to have an accident, you can go to the electrical store to buy a socket, connect the three-pin socket, and then plug two holes into the two-pin socket of the purchased socket.

Yes, some three-prong sockets are compatible with two-prong plugs.

There is no way to insert the fixed hole, and the adjustable one can be inserted by turning the appropriate position.

Plug into the two holes under the three-pin socket. Some three-pin sockets can't be helped!

Some of the 2 holes can be turned, and the ones that can't be rotated are twisted into a figure-eight.

If only the two-pronged plug could be turned.

Things are man-made, and people have to use their brains.

No, you need to use a power strip.

Summary. There will be no safety problems, the use of three holes is relatively safer than two holes, and the voice control is always grounded, which is not easy to cause electric shock accidents.

There will be no safety problems, the use of three holes is relatively safer than two holes, and the voice control is always grounded, which is not easy to cause electric shock accidents.

My two holes just burned too.

In this case, it should be considered that excessive power consumption or improper contact of the socket will generate heat, resulting in this problem in the jack.

Can I see the ** I posted.

That's it, can I still use it.

Plug in three holes.

Yes. Okay, thanks, sorry for the excuse.

Please give a thumbs up, thank you beauty.

One socket plugs all the jacks and is ready to use without overloading. Otherwise, the socket will heat up, damage the electrical appliances and even cause disasters.

Proper use of power strips:

1. Sockets and plugs should be replaced in time when they are abnormal or aging.

2. Prevent the power lead from being directly plugged into the socket.

3. Do not change the size and shape of the plug. This will lead to poor contact between the plug and the socket, damage to household appliances and plugs and sockets, and even lead to disasters.

4. Do not pull the power cord when pulling the plug, so that it is easy to pull off the part where the power cord is connected to the plug, resulting in short circuit, leakage, fire and electric shock accidents.

5. Be sure to buy the new national standard socket, and do not buy the universal socket prohibited by the state. The three-phase jack of the new national standard socket is separated from the two-phase jack and has 5 holes; The three-phase jack of the multi-hole socket is combined with the two-phase jack and has 3 holes.

Generally, the power supply of the router does not exceed 10W at full load, and 2 are counted as 20W.

The maximum power of the general computer audio is only 40-50W (full load), if you dare to drive to full load, just wait for the angry neighbor to call Uncle JC to come to your house to check the water meter.

Generally, the full load power of the mobile phone charger does not exceed 10W, and the charger of the tablet is more than 10W.

The mainstream computer power supply power is about 600W (the real-time power is constantly changing.)

Generally, the wire used for household wiring, the thinnest is more than 1 square, and the copper wire of 1 square can pass more than 10A. The mains voltage is 220V, and it can also support 2200W. In extreme cases, 1 square copper wire can support more than 3000W of power.

The general national standard socket is 250V 10A, which is 2500W.

And the equipment marked by LZ does not add up to 700W (which is already a lot bigger), so there is absolutely no problem.

Whether a socket can be plugged into all the jacks and cause it to burn depends on the specific situation, mainly depending on the power.

The socket includes the connection line and access point, all of which have nominal parameters, if the quality is qualified and the connection is reliable, the power consumption of all electrical appliances on the socket is not greater than the nominal power of the socket, and it will not be burned out; But it may burn if it is:

The power consumption of all appliances on the socket is greater than the nominal power of the socket;

The power cord is aging or the local resistance becomes larger due to long-term use of bent and broken wires;

Loosening of the joint, oxidation and corrosion, resulting in increased contact resistance;

There are counterfeit goods, and the parameter indicators are unqualified.

Look at how much the socket is, assuming it is 10A, that is, it can be connected to 2200W electrical appliances (220V*10A). Your 8 appliances are not even 1000w, so there should be no problem.

It mainly depends on the power of the electrical appliances and the thickness of the power cord of the socket. The cumulative power you listed above is not very large, it can be socketed in one socket.

Have fun!

Absolutely. Fully plugged in, no more than the total power.

Like yours, this thing doesn't add up to 1000w. That's enough. The power strip design is 2500W.

No problem, the general power strip is 10A, which is enough to meet your requirements.

No problem, it's all small power, as long as it doesn't exceed 2500W. Look at the wires with the minimum wiring thickness.

Minor problems, the total power does not exceed 200 watts.

Can be used. There is a safety hazard when the socket is not grounded in the home. In use, the electrical appliance can be used without grounding wire, and it does not affect the performance of the electrical appliance in the slightest.

Once the electrical appliance leaks, then there will be a risk of electric shock. And connected to the ground wire, if the electrical leakage, the leakage current will flow from the ground wire to the earth, over the royal current over a certain leakage current, the leakage protector at home will trip, to avoid the occurrence of personal electric shock accidents.

Precautions for the use of sockets.

1. When using the socket, avoid pulling the plug with wet hands, because water is a conductor and can easily lead to electric shock accidents.

2. When some people pull the plug, they will pull the power cord hard, so many times, they will pull off the part where the power cord is connected to the plug, causing the electrical appliances to be unable to supply power normally.

3. If you find that the plug and socket do not match, you should take the method of changing the size or shape of the electrical plug. The most common is to break the ground pin in the three-pin plug and plug it into a two-pin socket.

The above content refers to People's Daily Online-"The two holes and three holes of the socket cannot be used at the same time"For security reasons? Experts explain their doubts.