-
First cut the paper to the right size, wipe the glass clean, and then uncover one corner and stick it, and the other corner is better than the amount.
Press the paper against the glass and pull the non-stick layer from the back of the paper to uncover.
If the glass is divided into length and width, glue the wide side first.
It's best to hold down the cellophane with a flat spatula and uncover it while rubbing it.
If you don't have this tool, after finding one or several fixed points, let the cellophane and the glass at right angles, uncover a little bit of the layer of paper, and then use your hand to pull it down, but the direction of the hand force must not be oblique, it must be perpendicular or parallel to the paper, otherwise it will be crooked.
If you don't think the part you've held looks good on the glass, you can fold a line of paper against the glass, and then uncover it, and the sticky side is facing outward, and you can press the line on the glass, and then you can remove the extra piece.
-
1.Rinse the glass with clean water (Note; The corners of the glass are clean) 2Add a small amount of dish soap to the water, mix evenly, and spray directly on the glass.
Moisture can be sprayed slightly more) to ensure that the film can move freely on the glass. 3.Tear off the cut glass film and spray some water on the glue side as well, and apply it carefully and evenly to adjust the appropriate position.
4.Use a scraper to scrape the water in the glass clean and flatten, and it looks like there are no bubbles. (When the moisture is bright and dry, it will naturally stick to it) 5
Use a utility knife to trim off the excess along the edge of the glass. That's it, it's a natural phenomenon that the sticky here is not tight, there is no need to lie, and it will be fixed in a few days. ]
-
It's not easy to describe ...... in wordsYou see if you can see it, first uncover one end a little, align the edge and paste it (it is best to stick it on the top first), and then use a rag to gently rush down along the pasted place, while rushing, while peeling off the backing paper, and finally if there are bubbles after pasting, you can use something dense but with a certain degree of flexibility to slowly push it out, such as a rubber block, if you can't understand it, I don't have a rut......]
-
1. Clean the glass to be pasted with cellophane, and be sure to ensure that the surface of the glass is smooth and smooth.
2. Take out the tape measure, measure the width and height of the glass, and use a utility knife to cut the cellophane according to the measured size.
3. Sprinkle more water or bubble water on the clean glass.
4. Tear the corner of the cellophane, and then slowly tear the whole cellophane from top to bottom, or from left to right.
5. Stick the side of the torn film on the glass, first align the two corners of the top and bottom or left and right, and then align the lines along the edge of the glass.
6. After all are aligned, press it with one hand, slowly tear the film back or down with the other hand, tear a section, and paste a section.
7. Use a scraper to scrape out the bubbles in the cellophane in time to ensure that it is smooth and clean, and then paste the next paragraph.
-
01 Be sure to measure the length of the glass before pasting the glass and buy cellophane with the right width. When cellophane is sold, it is generally in the shape of a roll barrel as shown in the figure below, you can ask the seller or the boss for its specific size.
02 Before pasting cellophane, you can put the cellophane on the table and flatten it, and you can choose some heavier items, such as water cups or flower pots.
03 When we actually paste cellophane, we start to stick the sticker from the left, and then paste it on the right, at this time, you can need two people to cooperate, you can paste the cellophane more smoothly, and you can pay attention to it when pasting, if it is an office cellophane, generally we choose this kind of horizontal strip as shown in the figure below, on the one hand, it can play a role in protecting privacy to a certain extent, on the other hand, we can also clearly see the general state of the office.
04 If you want to paste cellophane in the bathroom at home, you can choose the frosted shape shown in the picture below, which is more beautiful on the one hand, and on the other hand, you will not clearly see the specific situation of the bathroom.
-
The steps for attaching cellophane are as follows:
1. First of all, clean the glass with a scraper, and be sure to ensure that the surface of the glass is smooth and smooth.
2. Measure the width of the glass with a tape measure, and then use scissors to cut the cellophane according to the measured size.
3. Sprinkle more water or bubble water on the cleaned glass, tear the corner of the cellophane, and then slowly tear the whole cellophane from left to right section by section.
4. Press it with one hand, slowly tear the film back with the other hand, and scrape out the bubbles in the cellophane with a scraper in time to ensure that it is smooth and clean, so that a beautiful piece of cellophane will be pasted.
1. What is cellophane.
Cellophane is a kind of film-like product made of natural fibers such as cotton pulp and wood pulp as raw materials and made by adhesive method. It is transparent, non-toxic and odorless. Because air, oil, bacteria and water do not easily penetrate cellophane, it can be used as food packaging.
One or both sides of ordinary cellophane are coated with a moisture-proof coating, and then dried and humidified to make moisture-proof cellophane.
Second, the use of cellophane.
1. Food industry: The above information has introduced that the molecular chain of cellophane has a wonderful micro-permeability, which can allow commodities to breathe like eggs through the micropores on the egg skin, which is very beneficial to the preservation and preservation of commodities, so cellophane is widely used in the food industry.
2. Manufacturing: Because cellophane is made of natural fibers, it can absorb water in garbage and be decomposed, so as not to cause environmental pollution. It is widely used as lining paper and decorative packaging paper for goods.
Its transparency makes people understand the goods inside at a glance, and has the properties of moisture-proof, impermeable, breathable, and heat-sealable, which plays a good role in protecting the goods.
4. Home: Many families often have cellophane, because cellophane can keep food fresh, cover it on infrequently used household appliances or furniture, and prevent scratches after sticking cellophane on the glass. Sterilized cellophane can also act as gauze.
You can use a hair dryer to blow the cover hot and then tear it off. You can use a hair dryer to warm the book cover before tearing it off. >>>More
Cellophane is a shielding effect, and the decorative film can also play a decorative effect, but also play a role in heat insulation, explosion-proof, anti-ultraviolet function.
1. Chemical methods.
1) Wind oil essence removal method, with wind oil essence can remove self-adhesive paste. Apply wind oil essence (a little thicker) on the sticker, and wipe it off with a dry cloth after a moment of penetration, leaving no traces. If there is no wind oil, it can also be replaced by toothpaste, but the effect is slightly worse. >>>More
When you say operation, I mean construction.
According to the needs of the project, the film is divided into two types: the film on the glass of the existing building and the uninstalled building glass film. >>>More
The car film is to be pasted on the inside of the car glass, the reason is very simple, and then there will be no wind and rain on the inside, and the film will not be subject to too much external interference during the use of the film, because the film is glued, without the baptism of wind and rain, it must be very firmly pasted, and it will not be affected on the inside when used. Since the film is attached to the inside of the car glass, the wiper will definitely not scratch the glass film, because the wiper is on the outside, and there is no need to remove the car glass when pasting the car film. Car film is actually a very technical work, much more difficult than architectural film, because the car glass has a curvature, and the architectural glass has a curvature is not much, after a film is cut, it is necessary to bake and shape according to the curvature of the glass, and then accurately cut the film, and then the film is applied internally.