What should I do if the cabinet door hinge is too small?

If the cabinet door hinge is too small, it means that the quality of your cabinet door hinge is problematic, and you can replace a hinge with a little bit.

The cabinet door hinge is too small, it is a problem with the installation, you can remove it again, and it will be good to reinstall it.

Next to the cabinet door is a lotus leaf, put a few screws on this lotus leaf a little loose, and then you can use it again, and then it will not appear in this situation.

If the cabinet door hinge is too small, you can adjust the gap between the pins, and you can make it bigger and close it very tightly.

The cabinet door hinge is too small to close, you can change the hinge so that it may be better.

It may be that there is a problem with the quality of your lotus leaf, or it is possible that you adjust it too tightly, and it will be much better after sending it again.

If the door panel is not deformed, then it is a problem of the door hinge. Open the screw protection cover on the door hinge, adjust the screws up and down, and of course how to install the door touch to see if it is affected.

You can replace this with another one, and the spring of the merge door is better, and if the elasticity is better, he will be stronger.

You can replace the hinges and look for the ones that are stronger.

If you want to know the size of the general volume, you can check the content on the Internet.

Here's how to mix the page:

1. The front and rear adjustment of the ordinary hinge.

By loosening the set screw on the hinge, slide the hinge position back and forth, and there is an adjustment range. After the adjustment, the screws must be re-tightened.

2. Use the cross-shaped quick-release hinge to adjust the front and back.

This cross-shaped quick-mount hinge has a screw-driven eccentric cam that can be adjusted by turning the cam up to + without the need to loosen other set screws.

3. Adjust the side of the door panel.

After the hinge is installed, the door margin should be the same before making any adjustments. In this way, the adjustment screws on the hinge arm can be adjusted in the range of +. If thick door hinges or narrow door frame hinges are used, this parameter range is reduced.

A1Adjust the hinge back and forth, loosen the fixing screws on the hinge, change its position back and forth, and tighten it again after adjustment; 2.The cross-shaped quick-release hinge seat is used to adjust, which will have screws with eccentric cams, and the cams can be adjusted in the corresponding range without changing the rest of the screws; 3.

The side of the door panel is adjusted with the door margin in millimeters, so that the adjustment screws on the hinge can be changed within the range.

If you are satisfied with my service, please give me a review

If the cabinet door is not closed tightly, the hinge needs to be adjusted. Adjust according to the steps under the slow rock: and before.

1.Open the cabinet door and check that the hinge screws are loose, if they are tightened with a screwdriver.

2.Check that the hinges are even, if not, adjust the tightness. Usually there is a screw on the hinge to adjust the tightness, you need to use a screwdriver to adjust it, and you can tighten or loosen it.

3.If that still doesn't work, check that the hinge is installed correctly. Normally, the upper end of the hinge is mounted on the cabinet body, and the lower end is mounted on the door, and if it is installed in reverse, the door will not close tightly.

4.If none of the above methods solve the problem, there may be a problem with the hinge itself and the hinge needs to be replaced.

Note: Before adjusting the hinge, please remove the items inside the cabinet door to avoid affecting the adjustment effect. And disturb the shed in strict accordance with the instructions and follow the safety operation specifications.

The adjustment method of the cabinet door is not closed tightly and the hinge is as follows

Adjust the hinge back and forth, loosen the fixing screws on the hinge, and change its position back and forth; Adjustment is made with a cross-shaped quick-release hinge seat, which will have screws with an eccentric cam that can be adjusted in the range of minus to millimeter; The side of the door panel is adjusted so that the door margin is millimetre, so that the adjustment screws on the hinge can be changed in the range of minus to millimetre.

If the spacing between the upper and lower two seams, that is, the door and the door frame, is inconsistent, it is caused by uneven ground, which can be leveled by stepping feet; If the wardrobe door hinge is broken or not installed properly, the hinge needs to be adjusted or replaced; If the size of the door gap is not suitable, you need to adjust the tightness of the hinged screws, the screws of the overall wardrobe of this assembly are different from the general hinged screws, and they should not be too tight or too loose.

Different materials for wardrobe door panels

1. Pure solid wood cabinet door: that is, we often say that the tree log board, which is cut down and directly processed to make cabinet doors. This is really solid wood, but there are so many door panels, such a large log is precious, not to mention, a large area of the door is easy to deform, so there is almost no whole board of logs on the market to make wardrobe doors, although it is indeed a good thing, but it is easy to deform, and a waste of resources.

2. Straight panel solid wood: This is also a log plank, but it is directly spliced with the same specification of the log, which is a common solid wood cabinet door, in line with the practice of solid wood grade, and finger jointing board is not a concept.

3. Solid wood finger jointing board: This can also be called solid wood, but in fact, because this is a piece of wood shed answer finger joint, it can generally be spliced with solid wood scraps, and the cost is generally lower than that of straight fighting, but there is a point better than straight fighting, that is, the probability of resistance to fierce code shape, so the market for finger jointing board is very large, and it can have the characteristics of solid wood, and it can be strong and durable; The suit is inferior to the straight panel.

The adjustment methods for the poor closure of the wardrobe door are: adjusting the hinge before and after, adjusting it by using the cross-shaped quick-release hinge seat, and adjusting the side of the door panel.

1. Adjust the hinge before and after.

Adjust the hinge back and forth, loosen the fixing screws on the hinge, and change its position back and forth;

2. Use the cross-shaped quick-release hinge seat to adjust.

Adjustment is made with a cross-shaped quick-release hinge seat, which will have screws with an eccentric cam that can be adjusted in the range of minus to millimeter;

3. Adjust the side of the door panel.

The side of the door panel is adjusted so that the door margin is millimetre, so that the adjustment screws on the hinge can be changed in the range of minus to millimetre.

The reason why the wardrobe door is not closed tightly

1. If this situation occurs in the early stage of use, then it is likely that there is a problem during installation, the vertical direction of the door may not be safe, and it is also possible that the door itself is defective during production. If the wardrobe is not done, the bottom is not flat, and the right side is higher. This is a carpenter's problem, so you can only stick a thick tape at the bottom of the wardrobe to prevent it from sliding to the left.

2. If it is a situation that has been used for a long time, then it may be that there is a problem with the track of the wardrobe sliding door, which requires you to check whether there is any debris in the track, if there is, please clean it up in time, if not, it may be a hardware problem that needs to be replaced or repaired.

1.How to adjust the hinge if the cabinet door is not closed tightly?

1.Adjust the hinges front and back.

Use the fixing screws on the loose hinge to change the position back and forth, and the adjustment range is, tighten after the adjustment is completed.

2.Adjust using the cross-shaped quick-mount hinge.

Such hinge seats will have screws with eccentric cams that can be adjusted in the range of minus to millimeters without changing the rest of the screws.

3.Side adjustment of the door panels.

There is no need to adjust the hinges after installation. The door margin is so that the adjustment screws on the hinge can be changed in the range reached, and if it is equipped with thick hinges or narrow door frame hinges, this value range will be reduced to.

2. What should I do if the cabinet door is not closed tightly?

If you can't close the cabinet door tightly, you have to check if there are too many things inside. You can rearrange the door frame against it, and you'll usually do the trick. Then check if the door is deformed, because it will be deformed under the influence of humidity, so it cannot be closed.

Then check if the door is displaced. Under the action of external forces, displacement can also occur, resulting in a situation where it cannot be tightly closed. The common opening angle of the cabinet door is 90 degrees, which is a right angle.

The hinge usually has two or three card slots to meet the needs of use. In general, a three-point hinge is better.

When buying cabinets, give priority to hinges with many anchor points, so that the door panel can stay at any angle when opened, and there is no need to make a lot of effort, even if it is closed violently, it can ensure safety.

1. Adjustment of the front and rear of the ordinary hinge seat: loosen the fixing screw on the hinge seat, and the position of the hinge arm can slide back and forth, and the adjustment range is. After the adjustment, the screws must be retightened.

2. Before and after adjusting the seat using the cross-type quick-loading hinge: The cross-shaped quick-release hinge has a screw-driven eccentric cam that can be adjusted from + without loosening the other fixing screws.

3. Door panel side adjustment: After the hinge is installed, the door distance should be adjusted only after it can be adjusted. The adjustment screws on the hinge arm are adjustable within the range. When using thick door hinges or narrow door frame hinges, this parameter range is reduced to.

Adjust the door hinge slightly, when adjusting, observe the closure of the door panel, the door panel is close to each other, then the hinge on the inside of the side of the side that leans outside can be installed inside. Cabinet or door panel deformation: Replace cabinet and door panel.

1. Displacement of the hinge.

The hinge is an important piece of hardware, which is mainly used to connect the cabinet and the door panel. In daily use, if the user uses too much force between opening and closing the door panel, the door hinge will loosen and shift under long-term action, which will cause the cabinet door to not close.

Solution: Adjust the door hinge slightly, when adjusting, observe the closure of the door panel, the door panel is close to each other, then the hinge on the inside of the side of the side that leans outside can be installed inside. On the contrary, if the situation of the two door panels against each other is not serious, you can choose to loosen the screws on the hinge and then move it back for debugging.

2. The cabinet or door panel is deformed.

In the process of using cabinets, because the wooden board is affected by the dry and wet environment, the material will have a certain expansion or contraction change in shape. In addition, the kitchen environment is humid all year round, and the cabinet will be deformed by moisture, which will cause the door panel to be closed.

Solution: If the cabinet door is deformed, the only way to replace the cabinet and door panel is to replace the cabinet and door panel.

3. Too much storage.

When there are too many items in the cupboard, the cabinet door will also not close, because the exposed storage will prevent the door from closing.