Can I ask why I don t have network permissions after the router reset?

Of course, there is no network permission after the router is reset, and you need to reset your router before you have permissions.

The specific connection and operation steps can only be used for your reference, because different routers and different settings for using the router environment are not the same.

1. Connect the line between the network cable, the router and the computer, and start the computer and the router equipment;

2. After starting the device, open the browser and enter it in the address bar to enter the wireless router settings interface. (If you can't get in, please look at the nameplate at the bottom of the router or the router instruction manual, the default settings of different models of routers are different.) ）

3. An account and password to log in to the router appear in the settings interface, enter the default account and password admin, or refer to the manual;

4. After successful login, select the interface of the setup wizard, which will automatically pop up by default;

5. After selecting the setup wizard, a window will pop up to explain that you can set the basic parameters of the router through the wizard, and click Next directly;

6. Set up step by step according to the setup wizard, select the Internet mode, usually ADSL users choose the first PPPoE, if you use other network service providers, select the following two according to the actual situation, if you don't know how to choose, directly select the first item to automatically select, convenient for novice operations, click next after selection;

7. Enter the password applied for from the network service provider, and go directly to the next step after the input is completed;

8. Set the wifi password, try to make the alphanumeric combination more complicated, and it is not easy to be rubbed off the network.

9. After entering correctly, it will prompt whether to restart the router, select Yes to confirm the restart of the router, and you can access the Internet normally after restarting the router.

Win7 can't access the internet, can't access the router, IPv4 IPv6 all show no network access.

You specify the IP manually and try whether your Win 7 is home or flagship

Find the small hole on the router, it says reset on the outside, which means reset, poke it in with a small object such as a needle, release it in 5 seconds, and the freezing setting will be successful, and then you can operate according to the prompts, the specific steps are as follows:

1. Set the router password: open the browser, enter the general router address in the address bar or check the login information on the back of the router) Enter the route - enter the user name and password, (the default is generally admin). Click:

System Tools Login Password Modify --- Save.

2. Set the wireless network password: open the browser, enter the general router address in the address bar or check the login information on the back of the router) into the route - enter the user name, password, (the default is generally admin). Wireless Settings - Wireless Security Settings - Select [WPA-PSK WPA2-PSK].

Authentication Type: Automatic.

Encryption algorithm: AES.

The PSK password is the wireless password. Set the required password.

Restarting doesn't seem to be as simple as poking reset.,It seems to have to be held down and then powered off and then connected (without letting go in the middle) to reset.。 For details, you can see the manual.

Take a look at the router manual, it's not reset, it seems that it should be pressed reset before plugging in the power supply, then plug in the power, let go in 3 seconds, and then reset.

There are two ways to reset your router

One is to find a thin wire or straightened paper clip, hold the reset hole behind the router when the router is powered on, about 10 seconds or so, see that the indicator light on the router is all off and then light up, release the reset hole, that is, complete the router reset; After the reset is completed, you need to enter the router settings interface again, and reset the PPPoE account and password to access the Internet;

The second is to directly enter the router's settings interface, find the "System Settings" item, which contains the "Restore Router Factory Settings" item, and you can restore it; After the router restarts, go to the settings page and reset the PPPoE account and password.

After resetting the router, the broadband parameters are lost, and you need to reset the parameters of the router as follows:

1.Typing in the browser may be something else, marked on the router's nameplate);

2.Enter and password. (The password is marked on the nameplate of the router);

3.Click "Setup Wizard" in the left navigation pane and click "Next".

4.Select the "PPPoE" mode and click Next;

5.Enter the broadband and password (when handling the network, the operator gives the password), click Next;

6.Set the name of the wireless in the SSID; In PSK

In the password field, enter the wireless password you want to set;

7.Click Finish to set it up successfully, and restart it after saving it to use.

There is no wifi at home, teach you a trick, reset the router in 3 minutes, and the network can be connected.

If the router does not have network access, it does not have an external network, which means that there is no successful connection, and there are two reasons for this.

Fault 1: The line is not connected. The connection method of this router is to connect the network cable of the Internet or the network cable from the ADSL cat to the WAN port of the router. The network cable from the computer should be connected to the LAN port of the router.

Fault 2: The Internet access mode is selected incorrectly, or the broadband and password are entered incorrectly. This needs to be checked with the operator.

After the router is factory reset, all the original data will be erased.

You will need to reset your broadband settings before you can access the Internet again.

Here's how:

Take the TP-Link TL-WVR600G dual-band wireless enterprise VPN router as an example

First, open a browser and visit the Open Router login screen. Enter your username and password (default admin).

Second, enter the router operation interface, open the setup wizard, and click Next.

Third, set the wireless frequency band as needed.

Fourth, set the wireless name and wireless password.

Fifth, select the port.

Sixth, choose the way to access the Internet, generally we have to choose PPPoE.

Seventh, enter the broadband account password.

Eighth, wait for the router to run.

Ninth, the setting is successful, complete.

Hello answer, I have seen your question and am sorting out the answer, please wait a moment Hello, it will be a pleasure to answer your question. Personally, I think that, after inquiry, you can know, and find that the wifi is not connected to the Internet after resetting the router, it is recommended to unplug the power plug and network interface of the router, and wait for 10 minutes to reconnect. Generally, the network is a little faulty, turn it off and turn it on.

Open the browser, enter the default terminal configuration address on the back of the router in the ** bar, generally , enter the management interface of the wireless router, enter the username and password in the pop-up dialog box, and enter the router's settings interface. Next, select PPPoE (DSL Virtual Dialing), click Next, and enter the account number and password on the broadband number. Encryption:

wpa-psk wpa2-psk box. Finally, we click Next, then click Save, when the setting status is all displayed successfully, and finally click Save, the computer can go online. It's best to restart your router and reconnect your broadband.

That's it. Hope it helps! I wish you a happy life and a happy day.

1. It may be caused by the change of the broadband account and password set by the original router after the router is reset.

2. It can be handled as follows:

Step 2: Fill in the current broadband password again and save it.

Step 3: Redial the connection through the router.

You have entered the settings page of the Telecom Cat.

Set up your wireless router again.

Does the cat connect to the wireless router, do you do this:

Plug in the wireless router, don't pick up the cat first, reset the wireless router (restore the factory), connect the computer to any LAN port of the wireless router, enter the router gateway address in the browser address bar (on the label behind the router), enter the settings page, and set it according to the PPPoe (ADSL virtual dialing) method.

Then set the SSID, encryption method, and password. Save, restart.

After setting, connect the network cable from the cat LAN port to the WAN port of the wireless router.

Reset the router: Find a small hole or button labeled REST (or guest) on the router, poke it with a toothpick for more than 5 seconds, and go back to factory settings.

How to connect and set up the router: Connect the computer to the LAN interface of the router with a network cable, and set the router as follows:

1. Log in to your router (enter or log in in IE, enter the username and password, and the router label is there.) Usually admin).

2. Go to the "WAN" setting

A If your broadband is to have an account password, set PPPoE, fill in the account password, select Automatic connection as the connection mode, and confirm that if your carrier will be bound to your computer, select the virtual band to copy the terminal MAC address.

b If you don't need the account password, if you are given a fixed IP, please select a fixed IP address and fill in the correct address of the fixed IP address, mask, gateway, and DNS.

c If you don't need the account password and it is a dynamic IP address, please select a dynamic IP address and fill in the DNS address.

3. Go to the wireless settings, select WEP or WP2-PSK, set the wireless password, and remember this password.

4. Go to the "DHCP" setting and activate the DHCP server.

5. Set "LAN".

IP" is, remember to log in to the router with this IP in the future, and save it after setting.

6. Connect the broadband network cable to the "WAN" port of the router, and connect the computer to one of the "LAN" ports of the router.

7. The computer is set to automatically obtain IP address and DNS address.

Computers, hand shutdowns, and wireless devices should all be able to access the Internet.

If there is no wireless function, ignore the wireless part.