What does Panasonic MBDHT2510ERR30 0 mean?

This means that her canteen is a Panasonic brand, and then the meaning behind it is that the model of her version is 30 versions, so its overall update is also relatively fast.

The alarm is faulty, the alarm 18 can check whether the XB short wiring is connected, and this alarm will appear if it is not connected, and it is reported that the drive is broken, and it needs to be repaired or replaced.

This is just one of his models, and this model is still more convenient to use, you can do it willfully.

It's just a brand of it. And then the letters in front are the logo of his brand, and then the numbers in the back are his brand, but the approved power and some other data of his.

Then the words represent its fundamental frequency, which represents some of its specific values, in which it can achieve a very good use, and relatively good results.

What does Panasonic's data mean, of course, is the problem of the setting program in it, and Panasonic is also a very famous brand, and its quality is still very guaranteed, so it has been liked by many people, and he has been for many years.

One of the needs of the computer, you don't care, it's just a brand.

This is a specific built-in protocol standard, and the important thing is what kind of environment it is in when it is operating.

Hello, this should be a model of Panasonic.

Panasonic, what do you mean? I think this one like you must be introducing its model, as well as its specifications.

The rest is for you to go to Panasonic to learn about Panasonic's customer service or something, and ask about this news.

What does it mean to divide this? The word of him can be timely, that is, it should be a brand of something.

This is actually not interesting, he is a **, I hope it will help you.

Hello, give me an email address. or a QQI put information on this aspect. The pdf is sent to you.

You give me an email address and I'll send it to you.

There is an alarm that there is a fault, the alarm 18 can check whether the XB short wiring is connected, this alarm will appear if it is not connected, and it is reported that the drive is broken, and it needs to be repaired or replaced.

After the driver is powered on, press the setting button S once to enter;

Press the mode key M once to enter the parameter setting mode, select the parameter to be modified by the up, down and left buttons, and press the setting key S to enter the setting value of the parameter;

After modifying the setting value of the corresponding parameter, and then pressing and holding the setting button S for about 2 seconds, the interface will automatically return to the corresponding parameter setting mode par**

After returning to the corresponding parameterization mode par**, press the mode key M again to enter the parameter EEPROM write mode EE set;

Press the setting key once to enter EEP-mode;

After holding down the up button for about 5 seconds, the eep- - gradually increases until the reset or finish is displayed, and the setting parameters are written.

Master: I have instructions for using the Panasonic A5 series, the only thing is how to set the internal enable of the motor, I didn't find it, and please point out the pr000 in the parameter settings - which ones need to be set? Thank you! View the original post

First check whether the connector or plug is in poor contact, and then check whether there is any internal pins in the controller, the eyes can't see it, you need to use a meter, and you can find the fault as quickly as possible with the replacement method, if your machine has multiple motors.

It is an A5 400W driver, search the Panasonic A5 manual on the Internet!

The encoder communication is abnormal.

Refer to the diagram below.

Basically, the drive is burned out, and there is a possibility that the motor coil is burned, and you can use the same model of machine to install it to determine which one is broken, and I can help deal with it if necessary.

It is an A5 400W driver, search the Panasonic A5 manual on the Internet!

The output port of CP1H is connected to 45, 24VDC is connected in series with 2K resistor to 44, using external 24VDC power supply, 13 pins are connected to 0VDC, and CP1H output COM is connected to 0VDC with the same.

The line driver can also be connected to OC output control, see the actual drawing, please pay attention to the connection polarity pulse, pulse, and sign, sign, need to be reversed, the current is from +24VDC->pulse-> pulse->plc out->com->VDC, after finding the wiring error, the drawing has not been modified.

The CP1H-X40DT-D cannot receive 44-47, and X40 is the pulse form of the transistor output.

To use the CP1H-Y20DT-D PLC hair line drive pulse instead.