How to disconnect the online line of Lida fire 128en host?

Lida fire 128EL host cable, one of its disconnection methods, directly remove its plug to it, you can directly disconnect.

This kind of failure can only be repaired by the manufacturer, and if you deal with it yourself, you can only try it with the replacement method (replace the normal multi-line reel and the faulty reel and try again).

He should be able to disconnect it directly, in that data.

Lida fire 128 host connection wants to disconnect and cut off the power supply directly, I think it should be the best one and the most direct.

Lida Fire, his 128, his face, his address, his connection line is disconnected, we can still readjust the settings, and we can still bring good to all of us. Help.

It's actually very simple, you just have to do everything you can in the settings.

Liede Xiaofan 128101 how to disconnect the contact with the home page of the host? You can go and look up what you can find on the ninety-nine computer, and then there are actually many ways not to worry.

How to disconnect the contact line of Lida Fire 128 Chairman can be dismantled?

Yida fire 1281 security host even the limit how to disconnect, this, I didn't disconnect I didn't.

All you need to do is disconnect the network cable.

How to disconnect the Lida Fire 128 host connection from this? You should go online to look it up, or a professional can help you.

How to disconnect the Lida fire 1281n host online cable, you can disconnect it from the settings.

JB-QB LD128EN(M) Operation Instructions First of all, two menus are introduced: The following interface is the boot menu.

The following interface is the main menu.

You can switch between the boot menu and the main menu with the "Menu" key. (Most of the operations are performed under the "Main Menu" interface).

1. Check the fire alarm and fault based on the printed information. The printing setting method is as follows: under "Main Menu", "Multiplex 1", "Menu", "4 Print", turn on the printing content, "Confirm", "Menu" (exit), "Reset".

2. The main engine is used to reset the fire alarm. It can be done under both the "Power on Menu" and the "Main Menu". The operation method is: press the "Reset" button and enter the "password" (four times).

3. The operation method of self-test is: under the "Main Menu", press "Reuse 1", then press "Menu", and then press the "1 Self-Test" button, you can press "Menu" (exit).

4. Hand automatic switching The operation method is: under "Main Menu", press "Reuse 1", "Menu", "6 Global", "1 Auto", "2 Manual", "Confirm", "Menu" (exit).

5. Start the device The operation method is: under the "main menu", press the "start" button, the LCD prompts you to enter the password, the password is to press the "" button 4 times in a row, and the LCD screen prompts you to enter the address 0123 to start the device, (0 is the loop number, 123 is the address number). When you finish entering the device address, if the input is correct, the LCD will automatically display the specific part of the device, press the "OK" button at this time, the device will be started, stop resetting.

6. Start the eight-way disc (direct start fire pump, sprinkler pump and fan) The buttons on the 8-way disc need to be protected by the software lock, and the unlocking state will be valid for 30 seconds, otherwise the buttons on the disc will be invalid. The operation method is as follows: under the "Main Menu", press the "Multiplex 1" key, and then press the "6" (request) key, and the bottom row of the screen shows "Open 8-way disk is valid for 30s", then press "Confirm", and then select the corresponding "Number" key.

Usually this situation is the circuit board failure, the judgment method is: connect the equipment of the circuit to other circuits, after the fire alarm is triggered, see if the alarm can be normal.

Is it a short circuit in the line?

The logic of Lida Huaxin's alarm host is to be opened and operated with special programming software, and it is not possible to operate directly from the host.

This kind of fault can only be repaired by the manufacturer, and if you deal with it yourself, you can only try it with the replacement method (replace the multi-line disc with the normal operation of the slag core and the disc with beam dismantling and then dig and test).