Swift unlimited router line connection Swift cat way

You also need a network cable.

If your broadband has a cat, the wiring method should be: broadband home cable - > cat DSL port - > the router's line is plugged into the cat's LAN port - > computer (the network cable is plugged into the LAN port of the router).

The cat-to-router connection settings are as follows:

The first step is to connect the line according to the connection method between the router and the cat.

The second step is to enter the address you see on the router in your browser, which is usually.

Then enter,Enter the corresponding account and password,Generally, the newly bought admin is confirmed to enter the operation interface。

Since the address of the fiber modem and the wireless router is the same, it will cause conflicts, so you need to modify the address of the router, set the LAN port in the network parameters to modify the IP address as shown in the figure, click Save, and restart the router.

Step 3: Click on the setup wizard, click on the next step, enter the Internet mode setting, we can see that there are three options for Internet access, if your home is dial-up, then use PPPOE. Dynamic IP can be used by plugging the computer directly into the network, and there is a DHCP server on the upper layer. The static IP is generally a private line or something, or it may be a cell bandwidth, etc., and the upper layer does not have a DHCP server, or wants to fix the IP.

I chose PPPoE because I dialed. (It is recommended that you choose to let the router automatically choose the Internet access method).

If you choose PPPoe dial-up Internet access, you need to fill in the Internet account and password, which should be understood by everyone, and there will be an account number to open broadband, and it is OK to fill it in

Then the next step is to enter the wireless settings, we can see the channel, mode, security options, SSID, etc., generally SSID is a name, you can fill in as you like, and then the mode mostly uses 11BGNFor wireless security options, we need to choose WPA-PSK WPA2-PSK, which is so safe that it will not be hacked and rubbed by the network.

The next step is to set it up successfully.

Click Done, and the router will automatically restart, so be patient. The interface that appears after success.

I believe that there are many friends who are concerned about this problem "how to connect the fast router", and I will talk about how to see the administrator password solution of the fast router. FYI!

How to connect to the fast router

The steps to connect the fast router to the computer are as follows:

1.First put the cat and the wireless router.

Together. The network cable is first connected to the LAN on the modem, and the other end is connected to the WAN on the wireless router.

2.Click"Local connection"Then right-click"attributes"In the interface that comes out, find an Internet protocol and double-click to open it.

3.In the interface that comes out, select "Get Automatically" and click OK after setting all the settings.

4.Open the browser, enter and then enter your own, the password is admin.

5.Enter the interface of Swift Network and click "Setup Wizard" on the left.

6.Out of the chaotic interface, click "Next" directly.

7.In the interface that comes out, the default is to let the router choose the appropriate way to surf the Internet, and you don't need to change it and click "Next" directly.

8.Then there will be an interface to enter the account password, which is your account and password that you will be told when you install broadband, enter it directly and click "Next".

9.Then set the name and password of the router in the interface that comes out, and click "Next" after setting.

10.After clicking, an interface will come out for you to check the parameters you set, and click "Save" after confirming that they are correct.

11.After saving, a setting status will come out, and you can check that everything is normal in your settings so far.

At this point, the wireless router is set up, and the computer can connect to the Internet.

How does the Swift Router see the administrator password

Prompt "Note: The username you entered.

or the password is incorrect, please log in again", as shown in the following figure:

You have entered an incorrect username or password, please log in again.

The username and password of a general router are: 1. admin and admin; 2. Guest and guest. I've tried them all, but it didn't work.

In this case, the most likely reason is that you set the username and password of your router yourself, but you forgot it.

So, the only solution is to reset the router and restore it to factory settings.

The way to factory reset is to hold a toothpick or press and hold the reset button from the hole on the back of the router until the indicator light is fully lit and then turn it off, and then enter the router settings. The restored routing login account and password are the default accounts and passwords marked on the back of the router. For details**, please refer to the article "How to General Reset of Home Routers".

It should be noted here that the Swift Wireless Home Router generally takes more than 10 seconds for all the lights to turn on. If the lights are all on, the router has been successfully reset. The administrator's username and password will be restored to their default and can be viewed behind the router.

I will share with you how to connect the fast router solution, I hope you like it.

The wireless router is responsible for managing the data access and access of each device to the Internet, but the function is a little different from that of the cat. The cat is modom, and its function is to connect twisted pair lines such as ** lines to achieve modem and demodulation functions, so it is also called a modem. Some MODOMs also have router functions, and their routing functions are often not as convenient and configurable as those of individual routers.

Generally speaking, modom needs to be connected to the wired network, use the computer to dial up the Internet, after accessing the router, it can be dialed by the router, if it is a wireless router, it can release the wireless signal to cover the room, so that the mobile phone can directly connect to the Internet.

Therefore, if the model of Jiexun wireless router has MODOM function, it does not need to configure MODOM for dialing, and it is necessary to configure MODOM when you want to connect to ADSL and other networks that require dial-up. Individual cell networks and small operators directly pull the network cable into the room instead of twisted pair cables, so this kind of network can be directly connected to the Jiexun wireless router, and there is no need to configure modom.

Now the country popularizes high-speed broadband network, the operators began to implement optical fiber access, for optical fiber access must be connected to the "optical modem" equipment, the optical modem is responsible for connecting the optical fiber and dialing, part of the signal with the function of the wireless router, can directly release the wireless signal coverage, this equipment does not need to be connected to the wireless router, for only a single function of the dial-up optical modem followed by a wireless router coverage is necessary.

Swift wireless router with a cat depends on what kind of broadband you use, if the broadband is optical fiber, ** line to the home, then you must use the fiber optic cat and adsl cat, if the broadband is a network cable to the home, then you don't need a cat, you can use it directly to the wireless router.

It is not necessary to use a cat, unless you are a broadband dial-up user, then there is no way, you can only use a cat, but if you are a campus network or something, you can directly plug in the interface of the network cable is not needed, you connect the network cable from the interface, directly connected to the router, hope to adopt!

Of course, otherwise how would you go online? Unless you're a router with a cat. Swift routers don't seem to come with cat functionality.

Connect one of your computers to a network cable and type it in your browser.

Then set up your broadband connection account password in it, and if you connect to the Internet as a function, the next step is to set the key in XP.

Spring flowers are smiling, and firecrackers increase the joy and joy.

It's adsl, that's definitely going to be an anchor!

As you can see, you are connected to a wireless router, but you can't access the Internet, and the problem is: Wrong DNS

Step 1: Obtain the correct DNS.

Check if you get DNS automatically; If the DNS is manually entered, it is changed to automatic acquisition.

If it is already automatic, run ipconfig all via cmd (command line) to get the current IP DNS, and check whether the obtained DNS is consistent with the DNS obtained by the router WAN.

Then use a stand-alone dial-up network to access the Internet, and record whether the DNS obtained is the same as that obtained by the router's PPPOE Internet access.

If it's different, please set it manually, if it's the same, it's probably a quality problem with the router.

Also: Please check whether the WAN port of the router is connected to the Internet.

Have you turned on the wireless function? Follow the instructions, step by step, and don't miss the steps! No problem.