FAST fw300r V3 Router can t access the Internet, the network is LAN, set dynamic IP, no data recepti

Suppose the router that does not connect to the Internet is B

Router A requires a fixed IP address. You need to know the IP of Router A. Then use Router A as the DHCP server, and on Router B, you need to set up the DHCP client.

This can be an automatic IP assignment. What needs to be set on B is that the server with gateway IP is Router A is also the IP of Router A. The subnet mask can be set arbitrarily.

Generally, it is used as an intranet IP.

In this way, by default, Router A is a dynamic route and can receive information from the other party.

In this way, the whole network can be interconnected.

Instead of setting it to change the previous one, connect it directly, and then set the wireless password. You don't need to set up PPOE to go directly to the Internet. However, there may be a conflict with the original IP, so it is best to set a different IP

For example, the original wired IP is to set the wireless IP to achieve. It can be set in the network parameters, (but I didn't set it last time when I went to help the customer install it.) Pick it up and you can go straight to it.

Because I didn't see the original wire, maybe the IP of the original line was changed. So you can just connect it and use it).

You need to enter the router to set up, there is its IP address on the back of the router, enter it into the address bar of the IE browser, enter the router interface, and then enter the password according to its setting wizard, look at the system status, and get the operator's IP address to indicate that it is connected.

Router A needs to connect to the WAN port to this new route, and the dynamic IP is correct, note that if the first three parts of the IP of the two routes are the same, modify one of them.

I'm sure you've read the router manual.

Router is a common electrical appliance in life, and it is difficult for modern people to live without the help of wireless routers. Let me introduce how to set up a Fast FW300R wireless router

One computer, one router.

01 First, enter the address set by the Fast FW300R wireless router and click to enter.

02 Enter the login password in the login portal of the router settings, and click the arrow below to enter.

03 Then click on the wireless settings to enter the wireless settings interface.

04 You can set the name and connection password of the router in the wireless settings, and click Save to save the settings after setting.

05 After that, click on the Internet settings to enter the Internet settings interface.

06 In the "Internet Settings" interface, you can set the router's network mode, broadband name, and broadband password, and click Save after setting.

07 Finally, click the exit button of the browser to complete the setup steps.

Swift 300R wireless router restores factory settings, and then resets it and there is no network, indicating that there is no successful connection outside. There are two reasons for this.

Fault 1: The line is not connected. The connection method of this router is to connect the network cable of the Internet or the network cable from the ADSL cat to the WAN port of the router. The network cable from the computer should be connected to the LAN port of the router.

Fault 2: The Internet access method is selected incorrectly, or the broadband account and password are entered incorrectly. This needs to be checked with the operator.

Set up the router again, enter the broadband account and password, and reboot it.

This is due to the fact that your account is bound to the network card of your computer host, and you can unbind the network card.

Method 1: After dialing directly from the computer, then disconnect the network That is, let your account be disconnected, connect to the router after 3 minutes (restore the router settings first), and set the account password. to connect to the Internet. (A small number of privately contracted networks do not work this way.) ）

Method 2: After the router is restored, set the account and password, contact the network provider, and ask the network provider to help you unbind your account card. If you are in the network of Telecom, you can directly dial 10000 manual service, provide the ID number of the account holder of the network, and call the customer service of Telecom to unbind the network card directly from the location of the network.

Yours are restricted, please set the dialing mode to "Special Dialing" to try! Or do a "MAC address clone".

As long as you make sure that your network cable is not plugged in correctly, then there is no problem, you can see if your WAN port and LAN port are plugged in correctly.

Find the manual and set up the wireless router again!

Generally, it is login, the user name and password are generally admin, and there are generally three ways to set up the Internet, virtual dial-up, the operator provides the account number, password, or dynamic IP address login, or static IP address login, set DNS, only when the router normally accesses the external network, the computer or smart phone connected to the router can access the Internet normally.

You need to figure out your account information before you can set up a wireless router! Broadband access to the home, with a username and password?! Or are you connecting to a different route?!

Or if the optical cat enters the home and then connects to the wireless router, first figure it out, and then tell you how to get it!

After the wireless router has been restored to factory settings, you need to reset the network settings before you can access the Internet.

1. Click on the small computer icon in the lower right corner, click to open the network sharing center, click on local connection, and click on properties.

2. Double-click Internet Protocol version 4, select Use the following IP address, enter the IP address, subnet mask, and default gateway information displayed in the figure below, and click OK.

3. Plug the network cable from the broadband cat into the WAN port of the wireless router, and then use a network cable to plug one end into any LAN port of the wireless router and connect to the network card of the laptop computer at the other end, as shown in the following figure.

5. Then enter the username and password, by default it is admin (there is also a prompt for the original data on the back of the router) and click OK.

6. After entering the wireless router setting interface, select the Internet access method according to the setup wizard, select PPPOE if you have a broadband account and password, enter the Internet account and password provided by the broadband company, and pay attention to the case of the letters.

7. Click Save, then click Wireless Parameters, click Basic Settings, determine the SSID number, turn on the security settings, select the security type, create a password for WiFi, the password is recommended to be a combination of letters and numbers, and finally click Save, as shown below.

8. After saving, the laptop can be connected to the Internet through wired or wireless connection.

The wireless router must be cautious before resetting the operation, the reset is to restore the factory settings, all the settings are restored to the original state, the broadband account and password in the setting steps are provided by the broadband company, and you can inquire and verify through ** contact.

1. Log in to the router (for TP-Link routers: turn on your computer, click IE, enter in the address bar: press enter, pop up the login page and enter the username "admin", password "admin", for other routers, please refer to the router manual);

2. Click on the network settings on the left, select PPPoe in the WAN port settings, enter the username and password given by the operator (if you don't know, call broadband customer service), and enter the DNS address (you can check your local DNS address on the Internet);

3. Turn on the DHCP server;

4. For the wireless router, turn on the wireless network, turn on the wireless network function, and set the wireless login password (security option wpa-psk wpa2-psk, enter the key);

Save the parameters and it's OK,At this time, the desktop is already available,Then open the wireless network card in the right corner of the desktop to right-click to view the available wireless network,Now your router broadcasts the signal,Double-click to connect,Enter the key to get it。 Wired and wireless access is available.

Configure the IP on the computer to automatically obtain, and in the future, you can go to the Internet by opening the browser directly on the desktop, and finally connect the computer to the network (wired, can be) to check whether you can access the Internet normally.

If you can't access the Internet, you can only connect to the computer that can access the Internet normally after dialing up the connection on the router, log in to the router again, and clone the MAC address in the WAN port settings.

Then you do a factory reset again and press and hold that button. Then follow the steps to reconnect the router, and if you still can't get it right, get a new one as soon as possible. Because there is no damage to the machine from a factory reset, no matter how many times you restore it.

Open the browser, get the IP of the default gateway, which is ", and press the enter key to confirm: enter the normal username and password. The default username and password are generally admin,; Locate WAN, LAN, Wireless, and Routing Status:

After entering, we usually check and turn on the DHCP service first. Click on the "LAN Settings" button on the left, and under the "LAN Settings" tab, make sure that the "Enable DHCP Server" checkbox is checked, and the default IP range can be used later. When you're done, click the "Apply" button to save the settings:

In the future, we can click to the "DHCP Customer Information" tab to view the clients that have been connected to the router, and then we can configure the wireless network. Click on the "Wireless Configuration" link on the left, then under the "Basic Configuration" tab on the right, uncheck the box in front of "Turn off wireless cable" and click the "Apply" button.

The above is the setting of the local LAN belonging to the router, after the above settings are completed, it can successfully connect to the local network, that is, the network that does not require a password, if you need to directly connect to the broadband with a password.

Click "WAN Settings" on the left, then click on the "PPPoE User" single option on the right, and then fill in the correct PPPoE account and password below

The PPPoE account and password are the dial-up Internet accounts and passwords given to us by the ISP Internet service provider, and the other settings are exactly the same as those for dynamic IP users. Finally, we can decide whether the router will automatically connect to the network and keep the network connected.

If you want to use wireless, you must connect to the WAN port. The settings are as follows:

Method 1: Go to the routing settings interface, click LAN port settings, change to DHCP server, and then shut down the DHCP server. Then fill in the password in the wireless security field.

Method 2: If there is an Internet access method in the routing interface, select the automatic acquisition method and fill in the wireless secure Internet password.

There are two main reasons why the wireless router cannot be connected to the Internet after it is set up:

1. The user settings are incorrect;

2. Broadband operator issues, these two issues will be introduced in detail below.

Determine the reason for not being able to access the Internet:

Please remove the fast wireless router first, let the computer directly connect to the moden, optical modem or home network cable, and then dial the computer with "broadband connection" to see if it can access the Internet normally.

At this time, if the computer can access the Internet, it means that the user settings are wrong, resulting in the fast wireless router cannot access the Internet; If the computer is not able to access the Internet at this time, it is most likely a problem with the broadband operator.

What is the IP of your laptop when you are not using a router? This includes information such as masks, gateways, and DNS.

Try to restore the router to factory settings, that is, there is a round hole, marked as reset and prick it with a toothpick or needle or something like 5 seconds, the indicator light of the router will flash a few times to release, and then set it again.

At the beginning of the setup, you need to connect the LAN of the router with a network cable to enter the interface.

How to configure a wireless router:

1.The router is connected to the network.

2.The system is connected to the router.

Turn on the wifi of the computer, search for the default wifi name of the router (the nameplate on the back of the router is written), and connect to the wifi network. The first time you use the router, you generally don't need to enter the wifi password.

3.Go to the gateway page.

Open a computer browser and enter the gateway IP address of the nameplate on the back of the router (generally, enter the gateway configuration interface. (This interface will pop up automatically for new routes).

4.Set up a way to access the Internet.

Go to the WAN port settings in Advanced settings. If the broadband service requires dial-up, select PPPoE dial-up, otherwise you can choose DHCP to get automatically. To dial up PPPoE, enter the broadband account password, and select Automatic connection as the connection mode.

If DHCP is automatically obtained, you do not need to enter this field.

5.Set the wifi name and password.

Go to Wireless Security in the Wireless Settings and select WPA2-PSK mode for Security Mode. Select AES for WPA encryption rule. Set up a wireless network key. The router will automatically restart after setting, please enter a new wifi password to connect.

6.The configuration is complete and you can enjoy the network.

You prepare two network cables (the first one you have prepared, that is, the network cable that comes out through the cat (if you don't have a cat at home, you can have a network cable for entering the house);

The second is to buy a network cable sent by the router, if you don't send it, you have to make a network cable with crystal heads at both ends).

1.Change the local connection to automatically obtain the IP address.

2.The network cable out of the cat [or your own home network cable] is connected to the WAN port on the router, and the ports 1, 2, 3, and 4 of the router are connected to the back of the computer host.

network cable port.

3.Open the browser and enter the password of the router is admin

4.Enter the router settings screen, select the PPPoE (ADSL virtual dialing) method, enter your home account and password, and confirm, even if the setup is successful.

You can try the above method.