How to use a laptop wired router? 20

Connect a computer and router with a network cable, enter it in IE, username admin password admin into the router, and then set it up according to the setup wizard, you have to choose PPPoe for the card you bought, and then fill in the password, and then the default can be.

No routers.

There's a notebook in the bedroom.

That's a person connected to wired internet and then unlimited peer-to-peer networking.

Others use Wi-Fi to access the Internet.

The cat is connected to the router, and then every computer is connected to the router, which is considered four wires. You also have to adjust the routing. I have a router setup assistant here, you leave your email address.

Buy a router with installation instructions on it Four Each computer is connected to a network cable There is also a LAN port connected to the router Like tplink dlink, these brands of routers are good It is recommended to buy a wireless router Your laptop I estimate that there should be a wireless network card bar How inconvenient it is to connect to the online Internet is not much worse.

It's good to use a wireless router on a laptop. Simple.

It is recommended not to use wireless routing, you are bridging like this, wireless routing is more troublesome to set up, or it is better to use wired, anyway, the space in the bedroom is not large, and there are not many wires. The length of the cable depends on the length of the place where your router is placed away from your computer.

How to set up the laptop to connect the router with a network cable.

To connect the laptop to the router with a network cable, first connect the network cable to the router and the laptop, open the laptop and enter the IP address of the router, then log in to the router account and password, click Next, set the wireless network name, restart the router, and the setting operation is completed.

A router is an important output tool for network settings, and there are many ways to set up a router. The following describes how to set up a laptop to connect a router with a network cable

1. You need to prepare a network cable for normal connection in advance, connect one end of the network cable to the LAN port of the router, and connect the other end of the network cable to the network port of the laptop.

2. After the connection is successful, open the laptop, enter the IP address of the router, and then enter the router account and password on the web interface that opens.

3. Select ADSL Virtual Dialing on the entry interface and click Next.

4. Enter the broadband account provided by the broadband operator in the Internet account number, enter the broadband password in the Internet password, and set a comprehensive wireless password with high security factor in the password.

5. Click Restart, and the laptop is connected to the router with a network cable and set successfully.

Like desktops, you need to go to the router's settings interface to set it up, and the specific steps are as follows:

1.Open your computer's browser, enter it in the address bar of your browser, and press Enter.

2.At this time, the login box of the route appears, enter the password of the route and the password (lowercase admin) in the login box, click OK, and you will enter the route setting page.

3.Click "Setup Wizard", enter the broadband account number and password in the and password field to complete the setting.

Connecting to the router and setting up steps:

1. Connect the line between the network cable, the router and the computer, and start the computer and the router equipment;

2. After starting the device, open the browser and enter it in the address bar to enter the wireless router settings interface.

3. Enter the default account and password admin;

4. After successful login, select the interface of the setup wizard, which will automatically pop up by default;

5. After selecting the setup wizard, a window will pop up to explain, just click Next;

6. Set up step by step according to the setup wizard, select the Internet mode, usually ADSL users choose the first PPPoE;

7. Enter the password applied for from the network service provider, and go directly to the next step after the input is completed;

8. Set the wifi password;

9. After entering correctly, it will prompt whether to restart the router, select Yes to confirm the restart of the router.

**Step: Step One:

Step 2: <>

Step 3: <>

Step 4: <>

Step 5: <>

Step 6: <>

Step 7: <>

Step 8: <>

If you have dial-up Internet access at home, you can follow the steps below:

1.As shown in the figure below, if the splitter is not installed, the ** line is directly connected to the ADSL interface 2 of the modemThen connect the LAN port of the cat to the WAN port of the router, and connect any LAN port of the router to the network port of the host.

3.The network settings for your computer are as follows:

5.Restart your router.

If you follow the above steps correctly, then you can connect the desktop computer to any of the 4 LAN ports of the router without dialing, and you can access the Internet by connecting the wireless device to the wireless signal and entering the wireless password.

If my reply is helpful to you, please adopt it promptly.

If you have any questions, you can continue to ask.

Is your broadband an optical modem that does not need to be dialed or does it need to be dialed manually?

1.If you want to dial up, plug the original line from the cat to the computer in the WAN port of the route, and then plug the network cable from the port on any other route to the computer at one end and plug in the computer at the other end Set up PPOE dialing Set up the account. Just take it one step at a time.

Some routes are not, you can take a look at the setting address on the back of the router.

2.If you don't need to dial up, the plug-in order remains the same, first unplug the cable between the optical modem and the router, and then enter, set it to dynamic dialing, and set the LAN port of the router to a different address, for example, so that it can be directly connected, and the address of the route will be set in the future. . . Because the default address of the optical modem is also set, the route must be set to a different domain name, otherwise it will be unusable due to IP conflicts, and the router of this method completely acts as a switch.

1. Win key + R to open the running program, enter cmd and press enter to open the command command.

2. Enter netsh wlan set hostednetwork mode=allow ssid=(wifi name you want to set) key= (password you set) in the command command, and press enter.

3. Make sure the wireless network is turned on, open the control panel--- Network & Internet--- Network & Sharing Center--- change adapter settings.

4. Select your current broadband connection and right-click the attribute --- Share --- allow other users to connect through the Internet of this computer, tick, select wireless network connection for sharing network2,5, go back to the command command, enter: netsh wlan start hostednetwork Enter, the following content is displayed, and the wireless network sharing is opened successfully.

When the laptop is connected wirelessly, it can be shared to achieve similar functions as a wired router.

In the Control Panel, select "Change adapter settings", click "Ethernet", tick "Allow other network users to connect through this computer's Internet connection", and then OK.

Now, even more amazing is that after wireless access, you can also use the 360 free wireless hotspot function to create a new "wireless hotspot" without adding hardware equipment.

Yes. Wi-Fi, wired and wired networks are all connected first. Then share the Wi-Fi network connection to the wired network.

You go to buy 2 wireless network cards that receive wifi, and it's only a few dozen dollars, and then it's so far, you buy 2 network cables also cost a lot of money, you might as well buy 2 wireless network cards and plug them into the desktop, all use wireless, how convenient, generally repair computers or sell computer equipment and accessories everywhere, about 30 yuan a, ** There are a lot of them.

1 Yes, it can be done.

2 However, cable is not possible for the time being.

3 You can buy a wireless network card for the desktop, which is only 30 yuan4 Then set the laptop as a wireless router, that is, set up a hotspot5 The desktop searches for the wireless signal of the notebook through the wireless network card6 Then the desktop can go wireless.

No, unless you have a dual-port external network card.