How to install the four in one button How to install the seamless button

Updated on vogue 2024-05-03
5 answers
  1. Anonymous users2024-02-08

    You need a professional tool to install it

  2. Anonymous users2024-02-07

    The specific steps are as follows:

    1. First put the buttons you bought face down on the countertop, and then spread the position of the buttons on the pants on the table, pay attention to the correct position, and put the outside of the clothes down against the bottom of the buttons, and then take the nails.

    2. Aim the bottom of the button with a hammer to completely drive the nail into the bottom of the button, pay attention to the strength, the force is easy to break the button.

    3. If the button is broken, you can use pliers first.

    Or scissors cut off the aluminum feet inside the garment, then remove the entire button and nail a new button.

    Buttons:

    buttons, in ancient Rome.

    The original buttons were used to make ornaments, and the pins were used to tie clothes. In the 13th century, the button had the same role as it does today. At that time, people already knew how to open buttonholes on clothes, which greatly increased the practical value of buttons.

    In the 16th century, buttons gained popularity. With fast fashion.

    The rise of buttons has changed from the previous functional type to the creative type; Began to become a costume decoration, etc.

    Buttons not only connect clothes and keep them insulated, but they also keep people tidy. The chic buttons will also embellish the clothes. Therefore, it is an indispensable part of the structure of the garment. With the development of society, the use of buttons will become more and more convenient.

  3. Anonymous users2024-02-06

    The method of pressing the button to install it by itself is: with the help of three tools: hammer, concealed buckle, and punching.

    1. Observe the components of the concealed buckle. Divide a set of four sets of buckles into different types, with the upper leather block being one group and the lower leather block being another set of installed ones. Install the buckle surface first, and punch holes in the leather surface. Place the buckle on the base and put the leather over the buckle.

    2. Install another matching part, install it with an installation tool that has a protruding point in the installation tool group, and pay attention to the thin spring wire that is flat and do not press into the button, otherwise the whole will be scrapped.

    3. Align the mold with the buckle, and hit it with a hammer for installation, and pay attention to it, preferably in place at one time. Punch holes in the additional pieces of leather and prepare to install the clasp on the other side. Place the clasp on the base, put the leather over the clasp and put the last raised clasp on top.

    Install it with a recessed mold, align the mold with the nail, and hit it vigorously with a hammer.

    How do you remove the button by pressing it?

    1. We must know that tools are very important, if we only have ordinary pliers, there is no good skill, just use pliers to clamp the buckle hard.

    2. When we plan to use pliers to clamp the buckle hard, we must be careful not to pull it very hard, otherwise it is easy to drag the clothes.

    3. But if we use diagonal pliers, it is more convenient, as long as the flat mouth is attached to the fabric of the clothes, and then the button can be broken with the notch.

    4. In fact, the efficiency of diagonal pliers is higher than that of ordinary pliers, and it will be easier for girls to use.

  4. Anonymous users2024-02-05

    There are no signs or anything like that.

    Tools: hammers, hidden buckles, punches.

    Steps: 1. First observe the components of the concealed buckle. The four groups of buckles are divided into four sets of buckles according to the following figure, the upper leather is a group, and the lower leather is another group installed.

    2. Install the buckle surface first, and punch the hole on the leather surface.

    3. Place the buckle on the base.

    4. Put the leather on the buckle surface.

    5. Install another matching part.

    6. Use the installation tool group with a protruding installation tool for installation, pay attention to the flat position do not press the thin spring wire into the button, otherwise the whole will be scrapped.

    7. Align the mold with the buckle and install it. Hit it with a hammer, pay attention to it, and it is best to be in place at one time.

    8. Punch holes in several other Pitan limbs, and prepare to install the buckle on the other side.

    9. Place the clasp on the base.

    10. Put the leather on the button.

    11. Put the last raised button on it.

    12. Install with a recessed mold.

    13. The mold is aligned with the nail, and the top is vigorously beaten with a hammer, preferably in place at one time.

  5. Anonymous users2024-02-04

    Snap button installation method:

    It is necessary to install the buckle surface first, and then Lushen will go to the other side to install the closing surface. First of all, small holes should be made in the leather, and the buckle surface should be laid flat on the grinding base, a piece of fabric should be put into the buckle surface, and then installed together with the closing surface, which can be installed with the help of tools. When installing the closing surface, it is necessary to knock a little hard to make both sides fastened, and finally complete.

    Pay attention to the methods and use professional tools.

    First, the specific steps of snap button installation.

    Snap button off, just like what to do if the zipper head of the clothes fell off, is a tricky problem, but there is a way to solve it, first of all, you need to prepare the installation tool before installation, after the tool is ready, use the punching tool to make some small holes in the fabric that needs to be installed snap button, after the hole is punched, you also need to make another piece of the top, punch the hole in the corresponding position, if you are afraid of hitting the deviation, you can first mark the marked position.

    Snap button is a combination, take the snap button off the paper when you use it, but the paper must not be thrown away after taking it off, you also need to use it in the next steps, first put the buckle surface on the base, put the fabric prepared before on the mouth of the snap button, and then install the accessories.

    Be careful not to press the buckle against the spring line, otherwise the buckle will also break. In the process of installation, you also need to hit the hammer, in this process, you need to keep the tool vertical, but don't use too much force, otherwise the buckle may be deformed, and the whole process needs to be very careful.

    Second, the use of the snap button.

    The use of snap buttons is very extensive, its blind omen is commonly known as snap buttons, press the meaning of buttons, for snap buttons, mainly used in clothes and some daily supplies, it is more convenient to use, very common and very practical in daily life, because snap buttons are very strong and not easy to break after installation.

    Snap buttons are metal and plastic, in daily life, plastic snap buttons can be found to be used more, generally in clothing, and metal will appear on shoes and bags. In addition, snap buttons can also be used for fastening, which can be used in some small productions. It's just that it's a little difficult to install, so few people will install snap buttons.

Related questions
Joyoung JYL 350 model 4-in-1 blender
8 answers2024-05-03

I also have one at home, I bought it in August this year, and it works very well. If you exclude these two situations, you can go to the business for some consultation and do the replacement work, its motor warranty is one year, as long as the warranty period is not over, the sooner the better.

What is the function of a 4-in-1 gas detector?
5 answers2024-05-03

The four-in-one gas detector can detect oxygen, hydrogen sulfide, carbon monoxide and combustible gas at the same time, of which hydrogen sulfide and carbon monoxide gas can be selected with other gases according to the detection needs of the place. >>>More

THE DIFFERENCE BETWEEN IPHONE THREE-IN-ONE AND FOUR-IN-ONE
6 answers2024-05-03

The three-in-one code refers to the three codes on the fuselage, the code on the box, and the code inside the mobile phone are consistent. >>>More

Quadrangle I don't know how to get in 30
9 answers2024-05-03

**The courtyard is a further extension of the three-way courtyard along the direction of depth. The general practice is to add a row of back cover rooms behind the three-entry courtyard, but this kind of three-entry courtyard is not the one with the back cover room, but the first. >>>More

Professional production of small program development, the era of four-in-one has come
15 answers2024-05-03

Mini program is an application that can be used without **installation, it realizes the dream of "at your fingertips" of the application, and the user can open the application by scanning or searching. It also embodies the concept of "use up and go", and users don't have to worry about whether they install too many apps. Apps will be everywhere and ready to use, but without the need to install or uninstall.