How to do the veneer floor, how to laminate the floor

Now the decoration is mainly solid wood flooring! Spread a layer of plastic foam underneath and directly on the floor! There will be no thumping sound when such a floor is gone!

Straight nail method - use nails to fix the plank to the rough floor. This method is often used for thinner wood floors.

Floor nailing method – use floor nails to fix the planks to the rough floor instead of using straight nails. This method is easier than the straight nail method.

Bonding – Both laminate and parquet flooring can be bonded. Glue the boards to the wool floor.

Levitation method - this is the fastest and most convenient method of laying. The suspended floor is not in contact with the raw floor, but is suspended on it. Neither adhesives nor nails are used.

A layer of padding is usually sandwiched between the planks and the raw floor to prevent moisture and reduce noise. Suspended floors can be laid on almost any surface.

Wooden floors are afraid of water, so first of all, the waterproofing must be dealt with, and the kitchen and bathroom should not run out of water. Because most of them are suspended floors now, the second step of ground treatment must be flat, and the smoother the ground is when the cement is leveled, the better the overall effect, and the more comfortable it is to step on. There is a curing period after cement leveling, a stable process is required, the curing period generally takes about 12 days, curing is the key step of paving the floor, this process must be indispensable, this step is also an important step to prevent the ground from cracking and drumming and the floor is not deformed in the later stage.

When laying the floor, the incision should not be pushed too tightly, otherwise it will be easy to bulge. The floor belongs to the expansion period in summer, and generally needs to leave a gap of 3-5 mm, and a gap of 8 mm in winter. Consumers can first inquire about the material and expansion of the flooring purchased by the manufacturer, and inform the pavement workers, who will pay attention to seasonal adjustments.

The paved floors are protected with a protective film to prevent rubbing against the floor. Before paving the floor film, it is necessary to observe whether there is sand and gravel and other debris on the floor, and then protect it after confirmation, and seal the protective film with tape around it after paving to prevent the sand and dust of the decoration from entering and causing damage to the floor.

I don't understand, you don't understand this question, if it is a new home to paste the wooden floor, isn't there a decoration company or carpentry, but the basic steps I know, first, first use cement to lay a layer, to leave enough thickness of the wooden floor, second, is to install the wooden floor, I think you will definitely not be able to do it yourself.

1. The pavement scheme should be constant.

For each stadium, or theater stage, what materials to pave, and how to pave, are determined according to the actual parameters of the sports venue and the investment budget. Therefore, once the sports wood floor paving scheme is decided, it should not be changed easily.

Frequent changes to the design and construction plan of sports wood flooring will cause additional investment and even affect the construction period. Therefore, in the design of sports wood floor paving scheme, it is necessary to communicate and coordinate with sports wood floor manufacturers, clarify standards, and avoid unnecessary problems.

2. Customized products should be in advance.

The overall structure of the sports wood floor is basically all solid wood structure, and the moisture content of the floor will be done according to the climatic conditions and moisture content changes of the installation project site during production, which is generally about 6%-14% on average. Before ordering sports wood flooring, it is important to allow sufficient time for production in order to ensure the quality of the flooring.

3. Avoid cross construction.

Cross construction, that is, the paving of sports wood floors, is carried out at the same time as other construction projects of stadiums and conflicts with each other. The sports wood floor paving project should avoid cross construction, so as to affect the smooth progress of the sports wood floor pavement, or the construction of other stadium construction projects destroys the paved sports wood floor floor.

4. Supervision and acceptance should be involved.

Although it is said that the installation project of sports wood flooring is operated by the pavement engineer of the sports wood floor manufacturer. However, the stadium contractor and Party A should also arrange a special person to be responsible for tracking and supervision, and solve the problems in the installation of sports wood flooring in a timely manner.

Now there are two kinds of home decoration and flooring. One is floor tiles, and the other is wooden flooring. The cost of wood flooring is lower than that of floor tiles.

With the ground relatively flat, we started to lay it. First of all, we have to spread a layer of plastic cotton film on the ground. This is mainly to prevent the deformation of the wood floor from re-damp on the ground. Then we have to move some of the flooring to the mulch so that it is easy to pick up when we lay it.

According to the situation on the site, we have to choose to start paving from **. Generally, they start from a corner of the wall.

When the first slab is laid, the second slab must be connected to the first slab. There are slots and protruding inserts between the plates. The insert should be tightly fitted into the slot.

The specific operation is to pick up a board and first put the plug of the long side into the slot on the front panel. I let the side plug of the board enter the groove of the side floor by hand push. If there is a gap, you can hit it with a special tool on the hammer pad.

Make it a perfect fit.

If the main family asks for a place to be planted or something. We're going to measure it and cut it. The size must be grasped well, and the proportion must also be grasped when cutting.

The floor is laid on the upper floor. If there are walls on all sides. We're going to nail the stickers around the wall. One is to look good, and more importantly, to stabilize the wooden floor underneath.

If it's a wooden floor for a table, we have to nail the corners. It is also mainly used to stabilize the wooden floor. When nailing the corners, it is better to drive a few more nails. Just in case there's a bulge in the middle.

The villa master provides you with local building policies, building drawings, and villa design drawings;

Villa appearance renderings service, thousands of popular drawings for you to choose.

Villa Master.

1. Before paving the wooden floor, the floor must be cleaned and maintained to maintain the flatness of the ground, and then a layer of plastic cotton film must be laid on the ground, so as to prevent the ground from being moisture-proof and the wooden floor will be deformed, which is also very convenient when paving.

2. After determining the way of paving the wooden floor, the floor will be paved first, and the floor will generally be paved from the corner of the wall, after the first floor is paved, and then the second floor will be connected, and then there must be a groove and a prominent insert between the board and the board, and the insert must be strictly closed into the groove. It is to put the plug surface of the long side of a wooden floor into the groove in the front plank, and use the side of the push board to insert the surface into the groove in the floor next to it, if there is a gap in the floor, then you need to use a professional hammer to gently knock it.

3. If the wall is around the paving, it is necessary to put an iron wire plate around the wall, which can not only fix the wooden floor below, but also make the floor more beautiful and generous.

The above is the method of laying wooden flooring, you can understand it if you need it, I hope it can help you.

01 In order to ensure the effectiveness of laying, you need to prepare in advance. First of all, everyone should clean up the construction site, remove all irrelevant things, and clean up the garbage on the ground, including every corner. Then the ground is leveled, the horizontal error can not exceed 2mm, and if it is exceeded, it is necessary to find a way to level.

If the ground is uneven, of course, the foot feeling will not be good after the floor is paved. Then it is to trim the protruding or uneven parts of the ground such as edges and corners.

02 Wooden floors are prone to arching and deformation after moisture, in order to avoid this situation, we need to treat the ground with moisture. A common treatment method is to lay a moisture-proof layer on the floor, which can prevent the floor from getting damp in the future. The moisture barrier should be paved and the joints should be close together.

03 Once you're ready, it's time to start laying the floor. In order to make the effect of the floor more beautiful, it is best to pre-lay it first, divide part of the floor into two, and see it according to the size. Before sawing the floor, you can open all the floors and pick out the problematic or defective floors for sawing, which can effectively make full use of the local problematic floors without excessive loss.

Don't come up and take the floor and saw, that will increase the loss. The place where the floor is sawn must be selected in a place where tiles are easy to take care of, such as a balcony, otherwise the splattered wood ash will enter everywhere and be difficult to clean.

04 We all know that wood flooring has the natural properties of thermal expansion and cold contraction, in order to avoid deformation caused by extrusion between the floor, we need to reserve expansion joints at the part where the floor and the wall are in contact before laying the floor, so as to avoid the floor bulging. The size of the expansion joint is generally related to the expansion coefficient of the floor.

05 After everything is ready, you can lay the floor, the common laying method is to lay a long board next to a short board, the reason for this is to make the floor lay firm and not easy to loosen, the floor should be knocked with tools after the floor is assembled. Then down is the connection, which is generally covered with floor strips. But it can also be filled with glass glue, depending on what you like.

After the floor is laid, it is necessary to check it again and fix any imperfections.

06 Then it's time for the final process. It is the installation of the baseboard, and the joints to be made are tight and flush. And make sure that you can press down the cracks in the floor wall.

After the floor is laid, the next step is to install the strip, generally the floor is higher than the ground to use the high and low strip, the floor and the ground are as flat as this kind of flat strip.

1. Before laying the wooden floor, it is necessary to ensure that the ground is flat, and then lay a layer of plastic cotton film on the ground, the plastic cotton film is to prevent the ground from moisture-proof and deform the wooden floor, and then the wooden floor is placed on the plastic film, so that it is more convenient when paving.

2. First determine the method of laying the wooden floor, and then you can start laying after you have determined it, generally starting from the corner of the wall. When the first board is laid, the second board must be connected to the other. Then there are grooves and protruding inserts between the boards, and the inserts should be tightly fitted into the grooves.

3. If the four sides of the paving are walls, then nail the wire plate on all sides of the wall, the iron wire board is not only better-looking, but also the final thing is to stabilize the wooden floor below, and nail a few more nails when nailing the corners, in case there is a bulge in the middle.

Precautions for laying wooden floors:

1. The construction work of the wooden floor should be arranged in the later stage, and the construction should be polished and painted as soon as possible after the construction is completed, so as not to stain the floor or be deformed by moisture, and the moisture-proof measures should be taken when the wooden floor is laid, especially in the more humid occasions, the ground can be coated with moisture-proof paint or use the bedding treasure and moisture-proof film, etc.

2. The keel should be flat and firm, can not be reinforced with cement, can be fixed with bolts or Meigu nails, etc., for the selection of wood for the keel, larch or Liu'an wood with strong nail holding force should be selected. The spacing of the keel should not be too large, generally below 30cm, the two ends of the floor should fall on the keel, can not be empty, and each keel must be nailed, can not use water-based glue.

1. Screening the floor in the wooden floor when transporting, you need to place it in a cool place, the floor can also adapt to the indoor temperature, so that it will not be deformed due to the loss of moisture, and at the same time, you also need to see if there are flaws or color differences on the surface of the wooden floor, if there is a best place to spread it in a less conspicuous place.

2. Before laying the ground leveling floor, the ground also needs to be leveled, otherwise the floor is prone to hollowing, warping and other phenomena, and its service life will be shortened.

3. If the keel is laid on the solid wood floor, it is usually necessary to build the keel, the moisture content of the keel can not be too high, otherwise it is easy to deform, and the spacing of the keel needs to be kept about 30 to 40cm, if it is too wide or too narrow, the user will feel unstable.

1. The wooden floor cannot be bought and laid, and it should be unsealed and placed in the new house for a period of time before paving, so that the wooden floor can adapt to the new environment. 2. Don't think that the wooden floor can't contain water, in fact, without water, the wooden floor becomes very hard, and the feeling under your feet is different, so you should keep the water content of the wooden floor at about 14%, of course, this is checked with professional tools. 3. A certain gap should be reserved between the wooden grating and the ground base layer (primary school textbooks have taught us to know how to leave a seam) to ensure that the air inside the entire earth dragon is unobstructed, do not use cement mortar to fix the wooden grating, and the wooden grating should be firmly fixed on the ground with nails by using the method of skidding wedges.

4. Before laying the wooden floor, the wooden grille should be cleaned and sprinkled with moisture-proof powder and insect-proof powder. This is to prevent insects from eroding the material of the wooden floor and damaging the structure of the wooden floor. 5. The nails nailed to the wooden floor must be made with twist nails, and the holes should be drilled obliquely at the tongue and groove (the hole should be perpendicular to the length of the floor strip), and then nailed into the wooden grille, otherwise it is easy to cause the wooden floor to loosen during use.

6. After the wooden floor is laid, it should be covered and protected with cardboard, old sheets or old mats. The purpose of this is to protect the initial installation structure of the wooden floor and to strengthen its structure.

Hope it can help you, thank you.