-
Anonymous users2024-02-11OK. Wired connection:
Yes, there is no problem, you pull a network cable over to the LAN port of your neighbor's wireless router and connect it to the WAN port of your wireless router. Before connecting your home wireless router; You first go to the wireless router network parameter settings and change the address of the LAN port to; After changing DHCP to not enable. Later, you have to enter the wireless router and enter it in the address bar!
Wireless bridging. It's easy to say; The first wireless router fixed channel number; a second unlimited router; In the network parameter settings, the LAN port is set to;
Reboot into the second wireless router; Turn on WDS in the wireless settings and click Scan; Connect the first wireless router in the result.
Turn off DHCP; Change Start to Not Star.
I'll give you references.
-
Anonymous users2024-02-10As long as you have a network cable in your house connected to the router in your living room, you're good to go. Connecting this network cable to a router can completely solve the problem.
-
Anonymous users2024-02-09You can add a wireless router. However, you need to disable the DHCP function on the wireless router and do not assign addresses to the wireless router. Connect to the original router and have the IP address assigned by the original router; Modify the wireless routing CIDR block to avoid conflicts.
Steps: 1. Note: Do not connect the wireless router to the original router first, that is, do not plug the attracted network cable into the WAN port of the wireless router first.
The computer uses a network cable to connect to any LAN port of the wireless router, and then connect the power to the wireless router. Open your computer browser and enter it in the address bar. Log in to the management page of the wireless router and enter the login and password of the wireless router.
2. Enter the wireless router settings interface, in the "Network Settings" on the left, "Router IP Address" is changed to click "Finish" to restart the wireless router. In this way, the network segment of the wireless router is modified.
3. In this way, you can use it, log in to the wireless router settings interface, select "Internet" on the left menu, and select "Dynamic IP" on the right.
4. In "Wireless Settings", select "Enable DHCP Server" and check Cancel. The router reboots after saving.
At this time, you can plug the attracted network cable into the WAN port of the wireless router, and the mobile phone can be connected to the wifi to surf the Internet.
-
Anonymous users2024-02-08Wireless router can be said to be an important device in the home without network, through it, the network signal can be turned into a wireless signal; Through him, we can save ourselves the hassle of dialing. So can one network cable connect to two wireless routers?
1. One ruler Wanglu network cable can be connected to two wireless routers.
2. However, you need to connect a shunt, and the wireless router is a router with wireless coverage function that is used for users to surf the Internet.
In general, one network cable can be connected to two wireless routers.
This IP is only the address inside the LAN, and the address must be re-obtained for a different LAN, for the address allocation of the LAN, it is still the 32-bit allocation method that is still used, and it is the same in **. If you want to make it easier, it's better to let the machine search automatically. Hope mine is helpful to you.
Yes, but you must know how the host is online, otherwise you may not be able to configure routing. 1. If the landlord is a cat plus switch mode, then you must know the dial-up account number and password; 2. If the landlord is a fixed IP, then you must know his IP, subnet mask, gateway and DNS server address; 3. If the landlord has used a router, enter the address in the landlord's routing address pool (if the landlord has turned on the dynamic allocation of LAN ports, your route can be obtained automatically), and the gateway should enter the landlord's router address, and the DNS server should fill in the server address of the residential area, and note that your router address (the default address is the IP address labeled on the back of the router) must not be located in the same network segment as the landlord's, that is, if the landlord is, Yours is going to change to or the third digit is 2 254 for the other number.
In fact, even if you get through, you can't dial a number from multiple computers due to telecommunications restrictions, but the problem you said is not very clear, as if you only have one computer! If you just use one, you don't need a switch, just connect the network cable to the computer; If it is on multiple computers (it is better to have a notebook, because the notebook has a built-in wireless network card), connect the network cable to the notebook, and then set the wireless Internet function of the notebook. But the key thing is that you say that the computer does not have a wireless network card, it should refer to the desktop, if this is the case, then you must use a wired router, you just said again, an excuse is four wires and one is eight wires. >>>More
Just right, the day before yesterday to the customer to implement the plan you mentioned, I used Tengda and Swift two wireless routers to do, the customer's situation is that broadband downstairs, originally thought, the second floor can receive the signal, but the pain is that the second floor is not even a little signal, can not help but say that Tengda routing garbage, but the second floor is separated by several floors, and it is in the corner. No signal is also reasonable. Okay, let's get down to business. >>>More
And. LAN port; Just set these two IP addresses and you're good to go. >>>More