After installing the router, the computer can access the Internet, and the mobile phone cannot

My ipad wireless automatic acquisition is not good, change to static OK.

1. Query the routing IP settings through the computer first (in fact, if you haven't changed it, there are in the manual, basically all, or.

2. The mobile phone wireless is set to a static route, the IP address is set to or, and the gateway is set to the IP of the router. x is set to a maximum of 99 because most routing dynamic address assignments are 100, so addresses less than 100 are used.

Do you need to dial in?

If you need to, go to the router and select the "Setup Wizard" to fill in your password.

You can directly use the DHCP service item to check the DHCP service item and turn on DHCP

Turn on the wifi on the mobile phone, then click on the router, and ask to enter the wireless password of the router, note: it is the wireless password of the router, not the password of your home broadband.

If you don't change the "Wireless Settings" item when the router is set, that is the default password of the router manual, some are 1-8, some are 6 6, the router model is different, this must be seen in the "Wireless Settings" section of the manual.

MIUI system? It seems that there is this bug.,Either change the system.,Or set it to a static IP address.。

Mine also often can't find the IP address like this, every time I turn off the router for 3 minutes, and then turn it on again, generally it's fine. You try it too.

One is that the wireless route is not linked correctly, the wireless route is not linked to the network, the router is used as a switch, and the computer still dials up the Internet by itself.

The second is that the router's wireless network is not turned on.

The proper steps to install the router are as follows:

1. The network cable is connected to the WAN port of the router, and the computer is connected to the LAN port of the router.

2. Open the computer browser, enter the IP address of the router, and enter the settings interface of the router. Generally, you can check the manual of the router or the router will be marked with the routing IP on the back

3. Set the WAN port parameters. Generally, dial-up Internet access, select PPPOE mode, enter the account number and password, and the connection mode is automatic connection.

If you use the Internet in static IP mode or from another router, you need to select a static IP address, enter the IP address, gateway mask, DNS, etc. (These parameters need to be obtained in advance, you can connect the network cable directly to the computer, and then check the status of the local link of the network, you can see the IP and other data).

4. Set up a wireless network. Set the SSID number, encryption method, and password.

There is an exclamation point in the PC enabled state.

Solution: Check the local connection status of the computer and confirm that it is enabled and the driver is intact without an exclamation mark.

Is it "assigned by DHCP".

If yes, go to the route management page and connect the device.

See if there is a mac address on your computer, and if you have it, you can surf the Internet.

Pay attention to turn off dial-up software such as broadband connections that have been turned on on your computer.

If not, go to the route management page, enable the DHCP service, save the route and restart it, and disable the local connection before enabling it.

Solution: 1. Plug in the wireless router, don't connect the cat first, reset the wireless router, and connect the computer to any WLAN port of the wireless router.

2. Enter the router gateway address in the browser address bar, and enter the login username and password to enter the settings page.

3. Set up according to PPPoe mode, enter the Internet account and password.

4. Set the SSID, encryption method and password.

5. Save and restart;

6. After setting, connect the network cable from the WLAN port of the cat to the WLAN port of the wireless router.

If the mobile phone can be used, it means that there is no problem with the configuration of the router. It must be the wrong configuration of the computer, remember to set the IP address of the computer to be obtained automatically.

Set the IP address to be acquired automatically.

The computer can access the Internet through the router, which means that there is no problem with the network. The mobile phone can be connected to the wireless router, but it cannot access the Internet, usually the router WAN port is set up with a telecom DNS server, which causes the mobile phone to not be able to access the Internet normally. It is recommended to restore the factory settings of the router and then set up the wireless router again.

Tools Raw materials.

TP router.

Computer Setup steps.

1. Log in to the wireless router management interface through a computer browser, click System Tools, and click Factory Reset.

2. After the router automatically restarts, click the Setup Wizard, select PPPoE (ADSL Virtual Dialing), enter the broadband account and Internet password, and click Next.

3. The setup wizard enters the wireless settings, you can modify the SSID name, enter the PSK password (WiFi password), and then click Next.

4. After the setting is successful, click Done, restart the wireless router, and the mobile phone can be connected to the router through wireless wifi to surf the Internet.

Let's take a look at the range of the DHCP pool set by your router first, and whether there are Internet restrictions set in the router!