How to paste the glass film so that it does not bubble?

There are two reasons for the blistering of car film, first, the quality of the film itself is not enough, some businesses will use inferior film in order to make money, in this way, blistering has become a very common thing, the second reason is that the film master's own skills are not enough, or the window is not cleaned, and the residual dust is also a reason that cannot be ignored, which is more miserable, after all, it is not so easy to tear off, even if it is torn off and then pasted, it will cause irreversible damage to the window.

So how should this be handled? During the shelf life, you can go to the store to find someone to repair for free, and after the shelf life, you will never go to the store to find someone to stick, because it is really expensive, just to give others money for useless things, of course, don't be smart and stick it yourself, maybe it will get uglier and uglier, in addition, there are some radio lines and other things on the rear window, accidentally broken, the gains outweigh the losses, the following two methods can effectively solve this problem, one is very simple, one is the same, but a little test of people's patience.

The first is puncture with a small needle, which, although it may seem rude, is also recognized as the best method, convenient, harmless to the car, and also satisfies obsessive-compulsive disorder, who doesn't like it? The most important thing is to save money, one needle is enough, but don't poke the membrane off, just put a small hole and let the air slowly drain out, the membrane will flatten, but don't poke a lot with one bubble.

The second way is to take something to put the air pressure out, of course, this is for the bubbles on the edge, the principle is the same as our mobile phone film, I still remember when we shoot mobile phones, the film owner always accidentally leaves bubbles, so as long as you take out the bank card to put the air pressure out, the same principle also applies to the window film, but, after all, it is a car window, this method is a bit time-consuming to use, and it takes several repeated actions to press out the air, it is difficult to make some people feel uncomfortable.

Use a needle for small bubbles and a utility knife for large bubbles, and after cutting, you will squeeze from the edge of the bubble to the opening until the bubbles disappear. The dragon film itself is sticky, so you don't need to do anything else.

There are roughly three reasons for the appearance of bubbles, the first is that the glass has a curvature, and the shape is not completely set according to the curvature of the glass during the baking process; The second is that the glass is not cleaned or dust has been drilled into the pasting process; The third is the bubbles caused by the evaporation of the water in the installation solution too quickly after the film is attached.

If the bubbles are on the edge of the glass, you can use a scraper to heat up and deal with it (but you need to find a professional master to operate, do not deal with it yourself). If the bubbles are in the glass**, most of them are because they are sticking into the dirty things, and there is no other way but to tear them off and re-paste them.

The blistering phenomenon of car film is mainly due to two aspects, one is that there is a problem with the quality of the car film, and the car film bought by the car owner is an inferior car film, or a fake film. There are too many types of car film, and the height is uneven, some consumers think that the car film is not worth buying, so they just bought a cheap film, but they don't know that the quality of the cheap film is very poor, not only does not have the protective effect of the car film, but also releases toxic gas at all times, plus the workmanship is rough, the material is low, and the sun is exposed, it is easy to appear bubbles, deformation and hemming and other problems, affecting the appearance, blurring the vision, endangering physical health, driving safety, it is really unacceptable.

Another aspect is that the construction is not professional enough, resulting in bubbles. In order to achieve the desired effect, it is best to carry out the car film in a dust-free workshop to avoid the dust in the air sticking to the gaps in the car film and causing bubbles; Or the glass is not cleaned when the film is attached, and it is easy to produce bubbles after pasting. It is recommended to go to a regular beauty shop and ask professional construction personnel to operate it.

If your membrane has bubbles, if the foaming is small and not much, gently puncture it with the tip of a needle, then wrap the towel with a thin card and slowly scrape it flat; If the area is large and affects the line of sight, it is better to go to the physical store and let the professionals solve it.

However, no matter how many bubbles there are, you need to go to a professional film shop to inquire about the cause of the bubbles, which will not affect driving safety. If it is an inferior film, for the sake of health and safety, a new film needs to be applied. If you paste it again, you must choose a high-quality film, consult and experience more, and feel the effect before making a decision.

Car wrap is now very common, and wrapping for cars has also become a necessary choice for car owners after buying a car. But we can often see such a phenomenon, many cars will have a lot of bubbles on the rear window and side window glass soon after the car film, which greatly affects the aesthetics of the vehicle, what is going on? What should I do if this happens?

To figure this out, we first have to look at the causes of these bubbles.

There are actually three reasons for the appearance of bubbles.

The quality of the car film is not good, and the quality of the car film on the market is uneven. A lot of low-quality, poor-quality car films are said to be imported from abroad, in fact, the cost of these car films is low-cost, and the glue used is not good, many car owners buy it in order to save money, and bubbles will appear after a period of time.

Many people will find a master they can trust when repairing and maintaining their cars, after all, the film is related to the technical level and the tools used. In many places, you will have an apprentice apply the film to you, and improper craftsmanship or incomplete cleaning will cause bubbles to form.

After the car film was just pasted, the owner did not pay attention to the precautions of the car film, and did not maintain the car film in time, so that the bonding state of the car film and the window glass was not stable, which led to the existence of local blistering.

How to deal with blistering.

1.If the bubble is relatively small, you can use a utility knife to cut a small hole in the bubble, and scrape it flat with a paper hard card.

2.Puncture with a fine needle and then smooth with a cotton cloth, this can also only be used for relatively small bubbles.

3.If the bubble is closer to the edge of the glass, you can scrape it directly with the card, and the bubble will disappear after a few more scratches.

4.If the bubbles are caused by near air, you can tear off half of them and re-apply them according to the normal film process, which is not recommended to be done by yourself.

5.If the bubbles are not cleaned because of dust, etc., you need to find a professional to deal with them.

6.The car film of the regular car film shop has a warranty card, and once the car film appears blistered, it is necessary to go to the store to reload.

If the bubbles are not very large and the volume is large, you can cut a small opening and then scrape it flat with a scraper and grilling gun. If there are not many bubbles and the volume is small, you can use a needle to puncture the bubbles and flatten them.

If the bubble is relatively small, you can use a utility knife to cut a small hole in the bubble, scrape it flat with a paper hard card, puncture it with a fine needle, and then smooth it with a cotton cloth; If the bubble is close to the edge of the glass, you can scrape it directly with a card; If the bubbles are caused by entering the air, you can tear off half of them and re-apply them according to the normal film process; If the bubbles are not cleaned because of dust, you need to find a professional to deal with them.

Generally speaking, the car film has serious bubbles and can only be replaced, and there is no other way.

The car glass film is blistered, how to deal with it? This is definitely possible, you can use the car glass film, and then squash it with a needle to prick his blistering thing, or directly squeeze it to the corners of the hand to get rid of the bubbles, or directly re-apply.

If the car glass film is blistered, then you can remove it from him, drive the air sticker out again and then paste it up, so that the film is very smooth and clean.

If the car glass film is blistered, then you can use a flat board to drive out the bubbles, and then paste it down, so that the glass film is very beautiful and generous.

If the car glass film is blistered, it is recommended that you can find the place where you were filmed at that time to deal with it, and you can also use a needle to puncture the bubble by yourself, and then press it flat, so that it can look better.

After the car glass film is blistered, you can gently prick the bubble with the tip of a needle, and then use the card to squeeze out the air of the bubble.

The car glass film blisters, which proves that air is generated between the glass and the film, and you try to prick it with a needle to release the air inside, and then press it tightly.

If the number of bubbles is large and the volume is large, it is difficult to scrape flat, it is recommended that you change a car film, because at this time not only affects the appearance, but also affects the driving safety, if there are not many bubbles, and the volume is small, we can use a needle to puncture the bubbles and then flatten it

It is best to find a professional to re-check and re-apply the film, so as to achieve a more ideal use effect, without affecting the quality of the car itself, and at the same time, it is more convenient to drive safely.

Film blistering is the most difficult to deal with, because the air is not expelled from the inside at that time, causing bubbling phenomenon. In order to completely solve the problem, it is necessary to uncover one side and re-paste it.

If the film of the car glass is blistered, it means that there is a problem with the quality of the film or when pasting, you can go to the company of the film to ask for a replacement and replace it with a new one.

The blistering of the car glass film should be replaced, and the blistering is because the car film selected when pasting is not good. If it is caused by the poor craftsmanship of the employee, it should be replaced with a new car model.

How to deal with the blistering of automotive glass film? After enlightenment, it is treated with hot gas and heat treatment.

If it's a particularly small bubble, well, no problem. If you can squeeze out a particularly large amount of intraocular pressure, you will be able to pick it up.

What should you do with the blistering of the car glass film? Well, you should prick it with a small needle.

If you want not to leave bubbles when sticking the film, you must first clean the mobile phone screen, wipe off the stains, and then vacuum it thoroughly, paste the vacuum film Sakura, wipe the screen clean, tear off the side of the vacuum film, stick the protective film on the screen to squeeze out the bubbles, tear off the protective film with the date, and the mobile phone film is completed.

01 If you want to apply a film to your phone without bubbles, you must first clean the screen of your phone, and use a clean cloth to clean the stains on the edges of your phone. Usually the seller will bring an alcohol wipe, and it will be very clean to wipe the phone screen with this alcohol wipe.

02 Glue the film with a protective film on both sides to the phone screen, and then cut the vacuum film. Attach a cut part of the vacuum film to the side without the date, preferably near the edges.

03 Next, we need to wipe the screen clean, then tear off the side of the vacuum film, stick the protective film on the screen, and then gently squeeze it, be sure to squeeze out all the bubbles. When you do this, you must be careful, take your time, and squeeze out the bubbles of your spine little by little.

04 The last step is to remove the protective film with the date side, when doing this step, the action should be fast, fast, and the protective film will be pasted. Applying mobile phone film is also a skilled job, which requires more practice and care.