Ask for the insulation mortar rubber powder formula, it is to the formula of rubber powder, thank yo

Mortar queen mother.

Formula: 1. Production of ordinary mortar king: mortar king master material + base material (fly ash, stone powder, talcum powder, calcium powder, laterite powder, fine sand) = mortar king.

2. Production of water-retaining mortar king: mortar king masterbatch + base material (fly ash, stone powder, talcum powder, calcium powder, laterite powder, fine sand can be) + general masterpowder of building admixture = water-retaining mortar king.

3. Production of thermal insulation mortar: mortar king + foam board fine particles (the machine directly crushes the foam board) = thermal insulation mortar.

4. Production of anti-crack mortar: mortar king + fiber (polypropylene staple fiber, glass fiber and other staple fibers) = anti-crack mortar.

The master of mortar is a new type of high foaming concentrate exclusively developed by Chengdu Hengfeng Hongye Detergent Factory, which is a cost-effective product in the foaming agent and has several obvious advantages.

First, the product performance characteristics:

1. High foaming speed, can produce a large amount of foam in an instant, and the large, medium and small three-dimensional foam is evenly matched.

2. High foaming capacity, with high energy instantaneous foaming, rapid foaming and three-dimensional foaming ability.

3. High foam stabilization effect, the foam is durable, and the durability and foam stability of the foam are very good.

4. It will not be hard in winter, will not turn into water in summer, is in a stable state, and can be mixed quickly and evenly with basic powder.

Second, a wide range of applications:

1. It is widely used as foaming additives in the construction industry such as mortar king.

2. Widely used in foaming additives in light building materials and other industries.

3. Widely used in foaming additives in daily chemical and other industries.

4. Widely used in foaming additives in metal cleaning and other industries.

5. Widely used in foaming additives in sewage treatment and other industries.

6. Widely used in foaming additives in various industries.

Can you know that you are **??

If you can, send me a text message.

Now the industry is quite chaotic, and now the Ministry of Public Security issued the No. 65 document on fire prevention, which has a great impact on the industry. You should also be cautious when entering the industry.

You're talking about insulation mortar glue powder.

The formula will not be made public, you can try it and join the building solid mortar glue family to try it.

1. Formula (weight percentage):

Pregelatinized hydroxypropyl tapioca starch (from Thailand) 65-70%.

Polyvinyl alcohol powder (17-88, 24-88) 20%.

Hydroxypropyl methylcellulose 10-15%.

2. Production method: add various raw materials into the powder mixing mixer and stir evenly.

Instant glue powder can be quickly dissolved in cold water, stirring in a certain amount of water while adding the specified amount of glue powder, stirring for 1 5 minutes to dissolve all the glue powder, standing for 15 minutes can become glue.

Hello dear, glad to answer for you, <>

In general, the installation of our insulation board is installed in a combination of sticking and nailing, and the sticking method is divided into strip sticking method, point sticking method, and full sticking method. Among the three methods, the full adhesive method is the most effective pasting method. Bonding mortar with polymer Thick rock wool board:

Set of JJ-18, the material is priced according to 80 thick rock air disturbance cotton board 3, steel wire mesh: JJ-52 4, rubber powder polystyrene board particle insulation mortar: JJ-27 5, pressed into a layer of alkali-resistant plastic-coated glass fiber mesh cloth:

JJ-50 6, scrape putty 2 times: B5-308 7, brush paint twice: B5-364 The 10-thick adhesive glue powder polystyrene particles in the exterior wall veneer brick wall are smeared with cement mortar on the insulation board, and the wall cement mortar quota Doushan sub-item can be set, but it is necessary to convert the cement mortar ** Li Kong.

The formula is as follows: 1. Pre-gelatinized hydroxypropyl tapioca starch produced in Thailand, accounting for 65% to 70%;

2. Polyvinyl alcohol powder, accounting for 20%;

3. Hydroxypropyl methylcellulose, accounting for 10 to 15 percent.

Production method: Add the above three raw materials into the powder mixing mixer, stir evenly and then package and sell.

Product Description: This product is the cold-water instant melt powder with the lowest cost and the best construction performance in China, which is easy to use for long-distance transportation and construction site, and has great market competitiveness.

Cold-water instant building rubber powder is produced by Huizheng's new polymer materials, which has cold water instant, clear and transparent solution, high bonding strength and good construction performance, and can be mixed with talcum powder, double fly powder, light calcium powder, gray calcium powder, gypsum powder, white cement and black cement. It can be used not only to produce glue, but also to produce putty powder, insulation mortar, etc., which is easy to use, low cost, environmentally friendly and non-toxic. 1 kg of glue powder can produce 50 kg of glue. Hall wheel.

Method 1: Ash method, take a certain amount of redispersible rubber powder, weigh it and place it in a metal container, raise the temperature to about 1000 degrees, cool it to room temperature after cauterizing at a high temperature, and weigh it again. Redispersible rubber powder is lightweight***.

Method 2: Film forming method, take a certain quality of redispersible rubber powder, dissolve it in 2 times the water, stir evenly and let it stand for 2 minutes, stir it again, pour the solution on a piece of flat clean glass, and place the glass in a ventilated shade. Allow to dry sufficiently and peel off.

Observe the peeled off polymer film. High transparency***. Then carry out a moderate pull, good elasticity ***.

Then cut the film into strips, soak it in water, and observe it after 1 day, and there is less *** dissolved by water. This approach is more objective.

Method 3: Dissolution method, take a certain amount of dispersible rubber powder and dissolve it in water with 5 times the mass, stir it fully and let it stand for 5 minutes before observing. In principle, the less repermissible matter that precipitates to the bottom layer, the better the quality of the dispersible powder. This method is simple and easy.

Not beat around the bush! Put latex powder in the insulation mortar, in fact, I have been paying attention to this problem of latex powder and no latex powder insulation mortar is not much different, to 3% when there is a significant change, but the cost is too high and there is no market competitiveness, of course, in the anti-cracking mortar, plastering mortar, bonding mortar in the latex powder is still essential and the changes are obvious.

The choice of latex powder, the insulation mortar should be selected as much as possible to increase the viscosity of the latex powder, and the plastering mortar anti-cracking mortar must choose flexible latex powder

Common foreign brands (note: there are many merchants who fake foreign brands, in fact, they don't exist at all), and the quality is trustworthy!

Domestic brands, most of the manufacturers are to reduce costs and make profits, so we must make a good choice, do experiments, and after selecting manufacturers, they will be more cost-effective than foreign brands!

What's right for you is the best!

Beijing Tricor Building Decoration Materials "Company" Factory2011-06-16 20:55:32Main Products:

1. Water-resistant putty for interior and exterior walls, flexible putty, tempered melamine coatings, general pure rubber powder; 2. Thermal insulation bonding plastering mortar [vitrified microbeads, polystyrene particles, fireproof board] general pure rubber powder; CPICS258253, glue powder and other three categories of high-purity rubber powder.

Hello! Rubber powder polystyrene particle insulation mortar is a new type of wall insulation material, composed of rubber powder and polystyrene particle light material, on-site water can be used, its thermal insulation performance is good, the construction is simple, the adhesion is strong, the outside is covered with mortar, fiber reinforced anti-cracking can solve the problem of surface layer hollowing cracking.

1. Rubber powder polystyrene particle insulation mortar is composed of rubber powder and polystyrene particles, the two materials are packaged in separate bags, and are made by adding water and stirring in proportion when used (rubber powder 1:2), the material should be used up within 4 hours with stirring.

2. The wall should be cleaned and free of oil stains, floats and sinks. The loose and weathered parts of the old wall should be removed cleanly, and the protruding parts on the surface should be smoothed if they are larger than 10mm.

3. For concrete walls and block walls, the interface mortar should be full.

Fourth, the thickness of the first insulation layer is not more than 10mm, and the thickness of the insulation slurry is not more than 20mm after each time, with an interval of more than 24 hours.

5. When the polystyrene particle insulation surface layer is used as a pasted surface brick, the metal mesh is used to replace the mesh cloth as the reinforcing skeleton of the anti-crack protection layer in the anti-crack layer, and the metal mesh is firmly connected with the structural wall.

6. The construction of the anti-crack insulation layer can only be carried out after the insulation layer is solidified and dried.

7. Wipe the anti-crack mortar with a thickness of about 3-5mm, and press it into the mesh cloth with an iron trowel immediately after wiping a certain width. The lap width between the mesh cloth should not be less than 50mm, press into one side first, and then press the other side with some anti-crack mortar, and it is strictly forbidden to dry it. The mesh cloth should be paved smoothly without wrinkles, and the fullness of the mortar should reach 100%.

8. The insulation layer and anti-crack protective layer should be protected from water washing, impact and vibration before drying.

9. The thickness and construction of the protective layer should meet the requirements of building energy-saving design, and the thickness of the insulation layer should be uniform and no negative deviation should be allowed.

This material should not be used for internal insulation

No, it's better to use perlite.

Then I suggest you make it with rock wool.