There is a problem with the D Link router after it is installed

You can't, set it up inside the computer (put the account).

You assign the account to Settings inside the route.

The purpose of buying a router is to offload and share the Internet.

You set it up in the router, and then plug in the network cables for each of the two computers.

You're almost not using a router in this case, and the router uses a single Internet account to assign to multiple computers, and you give Internet access to one computer, so they compete with each other).

If you want to connect both computers to the Internet, you can only plug the cat's mouth into the wan, and the other two plug in the lan. Then follow the router's manual to set it up. The router's manual is clear at every step. Especially when using cats to surf the Internet.

May I ask where you are from? Henan Netcom has banned the use of routers in various regions of the province since June 08, of course, there are many ways to crack and ban routers on the Internet. You can search on the Internet to see if the Netcom company in your area has disabled the router, this may be an explanation that telecommunications can be used but Netcom can't be used, I used Netcom before, from the disabling of routing to telecommunications, at present telecommunications can be used Oh, you should ask the customer service staff whether the router is disabled when you handle it, if it is a disabled router, search for the relevant cracking methods on the Internet can be done, good luck!

I don't know if you're telecom or Netcom.

Learning success means that you learn how to be successful.

The IP address, subnet address, etc. in the WAN are all super depressing......It means that the dialing of your WAN port is not successful.

Do you still need to set the correct PPPoE dial-up username and password for the WAN port, and set the username and password for PPPoE to use the username and password in the broadband connection? Yes.

1. Enter in the IE address bar: Enter the default account and password admin admin2, after entering the router, click the setup wizard, and then click the next time, the Internet mode selection appears, and select the PPPoe option here.

3. Click the next time to enter the broadband dial-up, enter the broadband account number and password 4, enter the wireless routing settings, select "on" for the wireless, and the other optional defaults, the mode is generally selected as the one of 54m.

5. Click Next to set the wireless password. You can fill in a longer password.

6. In the later stage, as long as the next time and the next time will be OK.

Hope you succeed.

In addition to connecting the line, you also need to set the parameters... The username and password are the account passwords for broadband.

Yes, the password is the same, turn it off and reset it, and restart the cat.

Dear users, hello.

I hope the following can help you:

1.Plug the broadband modem or home network cable into the WLAN port of the router, and then connect to the computer through the network cable or wireless network.

3.After entering the page, you will be prompted to enter management, which also needs to be found in the manual, and the general password is admin.

4.Click the Setup Wizard, follow the prompts on the page to set up broadband without PPPOE dialing, and enter the broadband password.

5.According to the prompts on the page, check the box to turn on the WiFi network, and set the password, when finished, click Next, and the device will automatically restart.

Anhui Telecom will serve you wholeheartedly.

Hello, I have seen your question and am sorting out the answer, please wait for a while Hello, I have seen your question and am sorting out the answer, please wait for a while

How to set up a D-Link router?

The specific operation steps of the D-link router to set the password alarm are as follows: 1. First of all, we need to use a network cable to link the router with the computer, and we will insert the computer network cable into the LAN port of the router to connect the computer and the router. 2. Then we open the browser in the computer and enter enter in the address bar to confirm, and then we can open the address of the D-link router setting.

3. Enter the main interface of Settings**, we select dynamic IP for broadband access type in the settings interface, and select PPPoE if you need a broadband account password. 4. Then we set the wifi name and password on the liquid surface, and click the link on the right to set the password after setting.

Hello! The router is simple to set up, but your problem is on your broadband. If you are a Netcom Broadband My World user, the Broadband My World client used by dial-up must be cracked before you can set up a router to access the Internet.

You can check out the cracked article in my blog:

This method is for Broadband Minecraft encrypted accounts. If you're one of those clients, you should be able to hack and use the router.

However, now Netcom has updated the client software, and some of the new clients use dynamic accounts, and some encrypt passwords. If it's two, the hack I gave you won't work.

You try to crack it, hope it can solve your problem, good luck!

First, it may be that your router did not choose the correct setting method, (this setting must be based on the Internet service you are doing) You refer to the manual specifically, which is more professional than me!

Second, a more mentally retarded question, are you sure that the Internet protocol on your computer is set? It should be set to get it automatically!! (Network Connections: Right-click on Network Connection Properties, and then scroll down to Internet Protocol, double-click).

Can you take a screenshot of the picture, the operation status of the wireless router is a picture of this page, I analyzed and analyzed the picture.

Let them try a different port for you. Changed in the network service ** business opportunity room.

You need to use a dedicated client to log in, so what's the use of your router?

Check the status of the wireless router and whether it is connected to the Internet. The address is.

The username admin password is empty.

There is nothing wrong with the routing settings, the problem is on your computer, don't listen to other people's nonsense. I don't believe you can't even connect routes, do you? Do you have any data in the WAN port?

If anything, the problem must be with your computer's settings! That's all!

If you don't know how to do it, I'll be fine!

The WAN port of the wireless router is not connected to the network.