How do I use trimming in CAD2010?

1. Click to modify the trim in the toolbar or use the command tr.

2. Select the boundary to be deleted, for example, delete the upper part of the red line in the figure, you can point the white line, take the white line as the boundary, and of course, you can also select all the elements. Selected content is displayed as a dotted line.

3. Click the location to be deleted, or you can use the box selection.

Click the trim key, select the intersection line to be cut and enter, and the point to remove the line segment after the intersection line becomes a dashed line.

tr Space Space, select the part you want to delete.

Step 1: Open your Quick CAD software, then enter the software operation interface, click the new command under the file at the top left of the software, and quickly create a new CAD drawing file for easy reference.

Step 3: After drawing, we click on the regular polygon, and then a property box will pop up, we click on the "Stretch" setting, and then you can click on the vertex to set the stretch, move to the appropriate position, and click the left mouse button to cancel.

Step 4: Then we click on the following command box to enter the trim command: tr - press the spacebar (the pointer turns into a small box) - press the spacebar again - put the small box on the line that needs to be trimmed - click. The extra lines are trimmed off.

Use the CAD Draw Line command to draw two lines that intersect and enter them on the command line"tr", press again"Spacebar", execute the CAD trimming command, select object refers to the selection of a pair of scissors, there will be a prompt"Select the object", now you need to select the shape object that needs to be trimmed off. The specific steps are as follows:

1. Use the CAD Draw Line command to draw cross-shaped straight lines that cross perpendicular.

2. Enter it on the command line"tr"Two letters, and then press again"Spacebar"to execute the CAD trimming command.

3. The command line will prompt"Select the object or Select All:"Select the green line.

4. At this time, the command will prompt again"Select the object", now to select the graphic object that needs to be trimmed, select the location of the cursor as shown in the image below.

5. The effect of the straight line being trimmed off is as follows.

Notes:

1. Be accurate when selecting the object to be trimmed, otherwise the result will be different.

2. If there are no intersecting lines, you can't use the trimming command, or the diagram that has been combined into blocks can't be trimmed.

1. We double-click the CAD shortcut icon on the desktop to open the CAD software and enter the CAD operation interface.

2. After opening CAD, we find the straight line command in the drawing.

4. After drawing the shape, find the trim option in Modifications.

5. Select the trim option, prompting us to select the object.

6. Select the figure we just drawn, we press the enter key and then click the left mouse button on the line we don't need, so that we get the kneeling figure.

Enter the command trim (tr) to select the line or pattern you want to trim, then press the space bar to select it, and then trim:

1. First of all, when using the trim command, pay attention to the relationship between the trimmed lines and the lines, otherwise you can't use the trimming command to trim.

2. After confirming that the trimmed lines are intersecting with each other, select the trimmed lines first, and hold down the left mouse button to select the lines to be trimmed.

3. Select the line you want to trim, and then click the trim button on the toolbar in the drawing window.

4. Click the trim button and then click the part of the line segment to be trimmed with the left mouse button, so that the line segment is trimmed.

5. Use the trim function, if you click the trim order when you don't select the line segment to be trimmed, we can click the right mouse button on the drawing window, and you can directly trim the line segment to be trimmed after clicking the right mouse button.

6. After selecting the trimmed line segment, if you mistakenly click the extension life, we can hold down the shift key on the keyboard, and then click the left button to trim the line segment.

How do I use the CAD trimming command? It's simple, let me teach you!

Tips for the "Trim" command in CAD.

Select the trim command first, and then select the part that needs to be trimmed.

Note that lines can only be trimmed if they intersect.

tr Press the space twice to cut off any line that intersects tr Press the space once to select a line Press space to cut the line that intersects the line.

Trim command in CAD. 2 straight lines must cross to trim.

Click the trim command.

Select the 1st line and press the SPACEBAR.

Click on the side of the 2nd line to trim and press the SPACEBAR to finish.

Select the line you want to build and the reference you want to build, enter "tr", then press the space, and then select the part of the line you want to subtract.

After clicking, trimming or extending, then right-click on the blank space of the screen, the whole screen, you can trim as you like, click down on the subtract symbol and press the space to trim, provided that the two segments must be crossed and closed.

Click on the modify command first, then click on the line segment that needs to be modified, then right-click, and finally click on the line segment that needs to be trimmed.

Hello, enter "tr" in the command bar, press enter, and then right-click the mouse, you can trim the unwanted part of the line in the CAD, good luck.

Left-click"Cut" - left click on the 2 red line, enter - left click on the 1 line to the right of the red line and press enter!

tr, drag from left to right, space. Trim again, as long as the lines intersect, you can trim.

First make a construction line, pass through the tangent point of the elliptical arc and the arc, (remember to pass through, such as vertical crossing, etc.), not tangent to the two arcs, but both intersect, (can't send a picture, will just take a look), and then trim according to the usual steps, and then delete the construction line OK. Good luck!

10. If you want to cut off the left one, the first step is to select the 丨 line, and after you are sure, then select the left one, and cut it out if you are sure.

Or, the second method, select the trim command, determine it twice, and select the horizontal to the left of the cross, and cut it directly.

tr: trim. 1: Click TR first

2: Select the line that will be handed over to the trimmed object.

3: Tap on the line you want to trim. (The end you don't want).

tr, space, space, and then space, select the place you want to build.

In snapping, turn on tangent snapping.

Then there is the use of the trim command, which is generally used in this way.

1.Enter tr on the command bar

2.Press Enter.

3.Press the spacebar.

4。Mouse to select the arc to trim.

In this case, you should be able to trim by following the steps above.

The general tr command is just like this 4 steps, just remember it. The other functions of trimming are not used at all, and they are generally left alone.

And I want to ask weakly, are you sure that the two arcs you drew are tangent?

TR is used for cutting, and EX is used for extension

The CAD trim tr command is simple to use.

The steps for CAD trimming are as follows:Operating environment: Lenovo YangtianM4000E-06, Windows10, etc.

1. Click the trim icon in the CAD toolbar and click the "trim" tool icon.

2. Select the trim boundary in the area, select the object as the trimmed boundary, and press the spacebar.

3. Click on the trimmed object and click on the trimmed object.

4. After trimming, press esc to exit, and the graphic trimming operation can be completed.

5. Skip BoundaryIn addition, in the Select Trim Boundary interface, press the spacebar to skip the selection boundary.

6. Click the trimmed object directly to complete the trimming operation of the figure.

The lines of CAD drawings can be trimmed with TR commands, as long as the drawings are not within the block.

1. Click the trim command or enter tr enter (space).

2. Choose the cutting edge, to cut the red, then the yellow one can be used as the cutting edge, and the cutting edge is actually equivalent to a pair of scissors.

3.Select the space to make sure.

4. After choosing, you can cut which part of the mouse can be clicked.

5. Tips: When selecting the cut, you can not select the direct space, by default all lines are cut lines, and holding shift in the trimming state is extending.

The most convenient operation of the trim command is tr under the amount of continuous space, you can cut which one you want! When you do need to cut a certain part, you can choose to cut the edge if you want.

1. Use the trim command: trim

2. The operation steps are as follows:

First: Trim the white line inside the red circle in the picture.

Second: Enter the trim command: trim and press the spacebar:

Third: After pressing the spacebar again, select the segment you want to trim:

Fourth: Effect:

3. The trim command is a command that is used very frequently, the effect of the extension command and the trimming command is opposite, and the two commands can be converted to each other by pressing the shift key during use.

There are three ways to do this, which are as follows:

Enter the command tr in the command line - Enter - Select Trim Boundary - Enter - Select Object to Trim - Enter (End Command) (If there is no boundary, the object can only be deleted, not trimmed).

Enter the command tr - press enter twice in a row (you can customize trim without borders) - press enter (end command).

Enter the command tr - press enter twice in a row - enter f - press enter - specify the first column selection point with the mouse - specify the second column selection point - press enter (end command) (so that objects that are within the column selection range and have boundaries will be trimmed).

1.Click the trim command.

2.Press Enter.

3.Just click on the line you want to trim.

Turn on the trim command, then right-click and left-click to fix the shape.

Enter the command: tr, click on the two intersecting parts of the diagram, and you can trim them.