How to maintain roller skating wheels, that is, how to exchange wheels for two pairs of shoes?

You have to play flat skating habits according to your own skating habits, I play flat flowers a lot, so the middle two wheels are bigger than the front and rear two wheels (when you buy it, it's bigger, the middle 80, the front and back 76 or 74) So if you play flat flowers, generally the first three wheels are more seriously worn, and then the inner edge is more worn out than the outer edge, so when you change the wheel, as long as the size of the wheel is better, let the wheels of the left and right feet be interchanged, and then when you change, pay attention to put the largest one in the third, the second largest, the second largest, and the third largest wheel in the first The smallest one is put in the fourth position on the line, of course, the first wheel and the fourth wheel can be interchanged, if you play flat flowers play less, then start from the first to put the smallest one to the fourth in turn, so it is more stable, this is my own experience summed up in practice, I hope it will be useful to you.

You're so lucky, before dinner, you had nothing to do and read the instructions that came with the roller skating you bought a few days ago, Pair of shoes for the left and right feet: The first wheel of the right foot is swapped with the third wheel of the left foot, The second wheel of the right foot is swapped with the fourth wheel of the left foot, The first wheel of the left foot is swapped with the third wheel of the right foot, The second wheel of the left foot is swapped with the fourth wheel of the right foot, (1 and 3, 2 and 4). I hope it can help you, by the way, I'm a beginner, and I will ask for more advice in the future.

The left and right shoe wheels are exchanged. The bearing uses a brush to brush off the dust, don't get water, and get some activated carbon inside the shoes to absorb the smell and ventilate.

Left 1 - Right 3, Left 2 - Right 4, Left 3 - Right 1, Left 4 - Right 2

Generally, the cleaning of roller skate bearings is divided into the following steps:

1.Remove the wheels from your shoes with a smile. The way to dismantle the wheels depends on the different specifications of the shoes, and generally uses a hexagon wrench.

Remove the wheels.

2.The bearings are removed from the wheels. There are two types of bearings on wheels, and sometimes it may be necessary to use special tools or small objects to eject the bushing.

3.Remove the cover of the bearing. Generally, the cover of the C-ring is attached to the bearing, which can be easily removed, but if it is a little more difficult, it can be removed with the help of other removal tools.

4.Cleaning the bearings. Place the removed bearings into a sealable container, such as a regular beverage bottle.

However, the opening should be large enough to fit into the bearing. Then pour in the derusting lubricating cleaner or kerosene, shake repeatedly, and then let stand for about 10 minutes.

5.Remove the cleaned bearing. Take the cleaned bearing out of the container, put it on a paper towel or cloth, let it dry, and then put a special lubricating oil on the steel ball, turn the wheel more than ten times, and then install the cover on the bearing.

6.Install the wheels. After attaching the bearings to the wheels, reattach the wheels to the shoes. A pair of clean and durable shoes are heavy, and a new shed has appeared.

Cleaning of bearings.

If the bearing is contaminated with dust, it can be cleaned with a dry cloth or toothbrush. If you want it to turn more smoothly, you can use a special maintenance oil.

Cleaning the liner Step 1: Put the liner in the laundry tub and add warm water.

Step 2: Add a soaking-ready, non-rinsing wash.

Step pin stove three: soak for one night, take it out the next day, and dry it in the shade.

Dress up (remember to use lukewarm water, if you soak it in cold or hot water, it will collapse and cause the liner to break.) ）

If the whole pair of shoes has to be cleaned, remember to remove the wheels, the wheels are not necessary to be cleaned, and the bearings should not touch the water, do not take the shoes directly in the water.

I've been wearing it for a long time, and it's dirty and smelly, and I can't bear it as a girl, but I don't know how to wash it.

Categories: Sports Sports >> Sporting Goods.

Problem description: Dry pie side skates.

Analysis: There are two types of roller skates:

One is to use rivets to inlay the tray at the bottom of the leather shoes, and screw the wheels on the bearing of the tray with screws, even a full set of shoelace wheels, the cost of this kind of shoes is low, suitable for general beginners; Dust Oak.

The other is the rollers and brackets that are sold separately from the shoes and wheels or only the roller skates, which can be installed by the athletes themselves after they are purchased. The cost of this kind of shoes is high, and it can be selected by Yuntan according to its own level, competition items, venues and other factors.

In addition, from the perspective of the arrangement of the wheels, there are differences between double-row wheels and single-row wheels, and in the current speed skating competition, more roller skates with single-row wheels and shoes are used together, which is what we often call single-row wheels, and the shoes of general speed competitions are 5 wheels. But no matter what type of skates you choose, you should buy them with a high quality and light weight, otherwise it will seriously affect the speed and jumping of athletes.

The quality of the shoes has a decisive impact on the performance of roller skating, the higher the level of skaters for roller skates, the higher the requirements for roller skates, and the cost of competition shoes for figure skaters participating in world competitions is 1000 US dollars.

Use and care.

Before each use of roller skates, all screw caps should be carefully inspected and any loose ones should be tightened one by one. Before using it, rotate each wheel a few times to check how flexible they turn, and if you find that a wheel doesn't rotate flexibly, it means you need to "refuel". If the rotation is still ineffective after refueling and debugging, you need to find a special technician to repair it, and you should not do it sloppily to prevent danger in the slippery run.

The tightness of the bogie can be adjusted according to your own wishes and requirements, if the bogie is too tight, it will not turn, and the tightness should be moderate.

Before learning to roller skate, you must first learn how to wear roller shoes correctly.

Unlace your shoes when you put them on, and when you put your foot into the shoes, you should do it slowly and not pull the lid too tightly. If the knotted laces are too long, tuck them or tie them around the shoe so that the remaining laces are a certain distance from the ground to prevent them from falling. After putting on your shoes, don't rush to get up and check if they are secure.

Shoes must fit well, and a bad fit will inevitably affect the correct gliding posture and technique.

The boot part of the skate also needs to be well maintained to prevent the leather shoe from "getting out of shape" and being scrapped prematurely. After each use, due to sweating, the skates are damp, and the shoes should be dried in a cool place in time, not exposed to the sun and baked, otherwise it will cause the roller skates to shrink, wrinkle, become stiff and cracked, and should be oiled frequently, and when not in use, the shoe "brace" should be placed in the shoe to keep the original normal shoe shape.

Roller skates can't be done by themselves, they must be done with professional technology, and they must go through a series of quality inspections. If you're looking for roller skates, check them out.

Selection criteria: 1. The upper should not be high, but it should also be able to support the pressure of the bias;

2. The upper is best the kind of hard shell with laces;

3. The shoe body should be flat, so that it is easy to control the left and right deviations;

4. The wheel frame is relatively firm, the material should be hard, and the frame should be short, and there is almost no gap between the wheels when the wheels are on the 80mm wheels;

5. Of course, the higher the bearing index, the better, ABEC-3 5 7 can be;

6. The wheels are generally composed of two 80mm in the middle and two 76mm in the front and back to form banana wheels.

That's what the factory did. There are a lot of processes.

Summary. Hello dear, glad to answer for you; The answer is; Because everyone's gliding state and sliding style are not the same, so the degree of wear and adjustment of the wheel is not the same, generally the left and right feet before and after the two wheels are exchanged, that is, the left foot front rotation to the right foot rear wheel, the left foot back rotation to the right foot front wheel, the best inside and outside of the wheel also do the transfer reversal, the general wheel replacement only needs half a month to a month can be. Thank you for your consultation, I hope mine is helpful to you and I wish you a happy life.

Hello dear, glad to answer for you; The answer is; Because everyone's gliding state and sliding style are not the same, so the degree of wear and adjustment of the wheel is not the same, generally the left and right feet before and after the two wheels are exchanged, that is, the left foot front rotation to the right foot rear wheel, the left foot back rotation to the right foot front wheel, the best inside and outside of the wheel also do the transfer reversal, the general wheel replacement only needs half a month to a month can be. Thank you for your consultation, I hope mine is helpful to you and I wish you a happy life.

Hello dear, roller skates refer to shoes with wheels, which are mainly used for entertainment in modern times. Roller skates are commonly known as roller skates, also known as roller skates The origin of roller skates is very interesting. It is said that as early as 1100, hunters put bones under the soles of long leather shoes in order to hunt even in winter, which is the earliest model of ice skates.

Summary. Yes, fancy skates can be made by changing the wheels so that all four wheels touch the ground. Here's how to change the wheels:

First, remove the wheels of the roller skates, then replace them with larger wheels so that they can touch the ground, and finally install the wheels back in place, making sure the wheels are securely mounted. When replacing the wheels, pay attention to the size of the wheels, as well as the installation position of the wheels, so as not to affect the use of roller skates. In addition, when replacing the wheels, you should also pay attention to the material of the wheels to ensure the durability and safety of the wheels.

Yes, fancy skates can be made by changing the wheels so that all four wheels are bothered to touch the ground. The way to replace the wheels is: first, remove the wheels of the roller skates, then replace the larger wheels so that they can touch the ground, and finally install the wheels back in place to make sure the wheels are installed securely.

When replacing the wheels, pay attention to the size of the wheels and the installation position of the wheels, so as not to affect the effect of roller skates. In addition, when replacing the wheels, you should also pay attention to the material of the wheels to ensure the durability and safety of the wheels.

Can you elaborate on that a little bit more?

Yes, fancy skates can be made by changing the wheels so that all four wheels touch the ground. The wheels of fancy skates are generally replaceable, and you can change different wheels according to your needs, and pick up the wide sail to achieve the effect of letting all four wheels touch the ground. When replacing the wheels, pay attention to the size of the wheels, as well as the quality of the wheels, so as not to affect the effect of roller skating spring hail.

In addition, the wheels of fancy skates can also be replaced according to different ground conditions, such as in the indoor ground, softer wheels can be replaced to reduce friction and improve the effect of roller skating; Outside, stiffer wheels can be replaced to improve grip and better control the direction of the roller skate. In conclusion, fancy skates can be changed so that all four wheels touch the ground, but pay attention to the size and quality of the wheels, as well as change the wheels according to different ground conditions to achieve the best roller skating effect.