How to paste the bricks, how to paste such tiles

If it is an old house renovation, it is best to use cement and construction glue to mix paste, which is more firm. Resistant to thermal expansion and contraction. And your old wall must not be just scraped, you have to use something to polish the wall.

Make more concave holes so that the bonding performance is good. Before use, put the tiles in a large container and fill them with water until the tiles are no longer bubbling, and then take them out, separate them one by one and let them dry naturally, and the tile surface can only start to be paved without water. In front of the tiles collage, there is a horizontal line of bullet bars on the wall.

Hang a thin line from top to bottom in the vertical direction. Fixed up and down. (To ensure that the vertical line is absolutely vertical, the distance between the vertical line and the wall is centimeters).

The direction of the collage is best to start from where there is a door. If you want to stick it beautifully, pull a line from the horizontal line, and the line is centimeters away from the wall. Press the line and stick it flat.

Specific collage method: If you haven't pasted it, it's best to find a platform, put the soaked tiles flat on the table, and the cement blended glue of the tiles can not be too thin or too dry, and pick up the cement with a gray knife, and the cement will not fall down It is very good. Then spread the cement on the tile, spread it all over the back of the tile, and the cement should not be paved too flat.

It is best to use a gray knife to make a concave and convex one, so that if the wall is uneven, the cement can be in place by itself when you are collage.

Wall knot tile, it is recommended to use special tile adhesive to stick, because now the tile is getting better and better, so the water absorption rate continues to reduce the traditional cement river sand can no longer meet the requirements of the tile, and the size of the tile is getting bigger and bigger, so it is more difficult to stick, the use of professional knot materials, so not only the adhesion force is strong, not easy to fall off the hollow, and the thickness of the knot is thin, environmentally friendly and non-toxic, the aesthetics and firmness of the tile have a good guarantee.

The following is the specific construction method of tile adhesive:

1. Pour the porcelain sticker powder into clean water and stir it into a paste (mixing ratio: 20kg powder 6kg water), after stirring, it needs to stand still for about 10 minutes, and then stir slightly before use, which helps to increase the adhesion force.

2. Use a toothed scraper to apply the glue on the working surface to make it evenly distributed and form a toothed shape.

3. Knead the tiles on the top during the drying time.

Find a good level, find a good centerline and you can paste it.

1. Make corresponding preparations in advance, and invite experienced masters to construct will speed up the tiling speed.

2. When paving tiles, the cement should be full and the amount of cement around the tiles should be about the same, so as to ensure that the tiles are firmly glued to the wall and will not appear hollow.

3. Tiles need to be tested to see if they are vertical, and the method is to carefully measure the verticality of each tile to ensure that all tiles are firmly sucked on the wall. If the decorator's craftsmanship is poor, the gap between the tiles will be large.

4. If you want the tiles to stick firmly to the wall, you must make the outer edge of the tile and the wall full of cement after the tile is pasted, so that the tile will be more firmly glued.

How to charge for tiling 400 800 bricks.

Hello, dear, tiling 400x800 brick charging standard such as the banquet: simple decoration is generally 500-800-square, ordinary decoration is generally 1000 square. Here's a breakdown down to some of the processes.

1. Demolition of the wall (including cleaning): 45 yuan square meters; Hydropower transformation: labor costs are calculated by square meters or meters, but the price is generally calculated in meters, and electricity transformation is 12 yuan and water transformation is 16-17 yuan meters

Removal of the original wall base layer (including restoration); 7 yuan square meter. 2.Carpentry worker's fee

The stone board ceiling is 35-40 yuan square meters, and the file sail silver is 120-150 yuan square meters. 3. Painting worker fee: latex paint 14-16 yuan square meters:

The transparent paint in the paint is 30 yuan square meters, the white enamel paint is 40-50 yuan square meters, and the colored paint is 50-70 yuan square meters. 4. The person fee charged for sticking to the wall and floor tiles is generally charged according to the size of the brick and the shape of the paving, and the size of the brick is large and dry + 300x300, which is priced at 30 yuan square meters: small dry and other ten 200x200, then it will be 80-90 yuan square meters:

If it is greater than 800 * 800, the labor fee is generally charged according to 70-80 yuan square meters: if the shape of the sedan car is not conventional, such as some diamond-shaped laying, it will be charged according to 30-40 yuan square meters. 5. The waist line of the wall tile is charged at 15 yuan meters, and the foot line is charged at 10 yuan meters

Even the kitchen and bathroom floor tiles are laid outside the sewer pipe, and the sewer pipe needs to be sealed, and the labor cost is 60 yuan root 6 When installing the switch socket gold lamp, the electricity will be installed in accordance with different charging standards, and the specific labor cost ** is: 5 yuan for the switch socket, 5 yuan for the downlight spotlight, 20-30 yuan for the general family lamp, and some particularly large crystal chandeliers start at 50 yuan for the cover. If my answer is helpful to you, please give a thumbs up (in the lower left corner), I look forward to your like, your efforts are very important to me, and your support is also the motivation for my progress.

If you feel that my answer is still satisfactory, you can click on my avatar for one-on-one consultation. Finally, I wish you good health and a good mood!

400 800 How to paste wall tiles so that they will not fall off.

400 800 wall book suspect brick how to paste so that it will not fall off 400 800 wall bricks to see what kind of brick, the wall will not fall off, if it is a full-body brick on the wall, do not tile glue and tile adhesive to paste, the time is slightly longer will appear hollow drum fall off if it is 400 800 soaked water bricks to the wall, do not use tile glue, simple cement and sand mixed evenly tiles will not fall off, provided that the tile must be completely soaked in water thoroughly, the wall sprinkled water and then paste will never fall off.

The most essential thing for a family is to have a kitchen.

The kitchen is a place for cooking, so many places will be filled with oil smoke, especially the walls of the kitchen, there are often some oil stains, and people will put tiles in the kitchen for this.

The kitchen tiles should be more firm, and there are certain methods and skills for tiling. kitchen tiles with other rooms.

The tile pasting method is no different, but people have to be more careful and deal with some corners and corners. So let's take a look at how the kitchen tiles should be pasted.

How to paste the tiles in the kitchen

1. Before tiling, soak the tiles in a large basin for 12 hours, and then take them to the shade and place them for 12 hours before the next step of installation.

2. Operating conditions.

Ground. After leveling, do a good job of waterproofing the ground and waterproof protective layer.

Do a good job of installing water and electricity pipelines, and plugging and smoothing scaffolding, eye and pipe holes.

Washstand. Mirror cards, pipe cards, water tanks, gas, etc. should be buried with anticorrosive wood.

bricks, in an accurate position.

Uniform pops up a +500mm horizontal line on the wall.

Construction technology.

As follows:

1) Clean up the base layer, clean up the mortar slag, dust, oil stains, etc. remaining in the base layer, and water and moisten it in advance.

2) 12mm thick 1:3 cement.

Mortar priming, priming should be layered, each layer should be 5 7mm thick, and then smooth and rub the hair.

3) Wait for the bottom layer to be ashed.

When the sixth and seventh layers are dry, according to the requirements of the drawings, the specifications of the bricks and the actual conditions, the bricks are arranged and the elastic line is carried out.

4) Use 1:3 cement mortar to stick the corner bricks on the ground as a reference point to control the ground tiles.

surface flatness.

5) Bottom ruler, calculate the elevation of the lower mouth of the next brick accurately, the upper skin of the bottom ruler is generally 10mm lower than the ground, and put the bottom ruler on this basis, which should be horizontal and stable.

6) Before the veneer brick, the face brick should be soaked in water for more than 2 hours, and then taken out to dry and set aside.

7) Wipe the 8mm thick cement mixed mortar bonding layer, scrape flat, paste the surface brick with the wipe from top to bottom, require the mortar to be full, remove and repaste when the ash is lost, and check the flatness with a ruler at any time, and ensure that the width of the gap is consistent.

8) After pasting the self-inspection without hollowing, unevenness and straightness, wipe it clean with cotton yarn and use white cement.

Slurry or pat dry cement to wipe the joints, wipe the plain slurry in the joints with a cloth, and wipe the brick surface clean.

Many people think that tiling is a difficult job and requires professional decoration.

Team to carry out, in fact, tiling is a work that requires patience and care, as long as you learn the method can be hands-on, but the professional team will be more flat than our own pasting, they have excellent work experience and time. If you have limited time, you can still ask a professional team, but it costs some money, if you have time, you might as well do it yourself to try it, according to the method you can easily paste the kitchen tiles.

1. Polished brick: Polished brick is a kind of bright brick made by grinding and polishing the surface of the whole brick body, which belongs to a kind of whole brick. Compared to full-body bricks, the surface of polished tiles is much smoother.

Polished tiles are hard and wear-resistant, making them suitable for use in most indoor spaces except washrooms and kitchens. On the basis of the use of seepage technology, polished tiles can make a variety of imitation stone and imitation wood effects. Polished tiles are easy to get dirty, and the anti-slip performance is not very good.

2. Vitrified brick: This is a kind of high-temperature fired porcelain tile in the shed, which is the hardest of all ceramic tiles. Vitrified tiles are more demanding than polished tiles.

The press is required to be better, to be able to press higher density, to be able to fire at a higher temperature, and to be able to achieve all-porcelain. Vitrified tiles are strengthened polished tiles. The surface does not need to be polished to be bright.

3. Glazed bricks: glazed firing on the surface of the embryo body. The main body is divided into two types: pottery and porcelain.

The back of the clay fired is red, and the back of the porcelain clay fired is grayish-white. The surface of glazed bricks can be made with various patterns and patterns. More colorful and patterned than polished tiles.

Because the surface is glazed, the wear resistance is not as good as that of polished tiles and vitrified tiles. 4. Antique bricks: not the products of China's building ceramics industry, they are imported from abroad.

Antique bricks evolved from colored glazed bricks, which are essentially glazed porcelain tiles. Compared with ordinary glazed tiles, the difference is mainly manifested in the color of the glaze, antique bricks belong to ordinary tiles, and magnetic sheets are basically the same, the so-called antique, refers to the effect of bricks, should be called antique effect of tiles, antique bricks are not difficult to clean. 5. Full-body bricks:

This is an unglazed porcelain tile that has good slip resistance and abrasion resistance. Most of the so-called "non-slip floor tiles" are full-body tiles. Due to the moderate price of this kind of brick, it is quite popular with consumers.

Now to paste 800*800 floor tiles onto the interior wall, you can use a special tile adhesive to pave. Specific construction steps:

1. Before construction, carefully check whether the base treatment meets the requirements of paving tiles.

The first thing you need to see is whether the original wall is suitable for paving tiles, such as whether there is hollowing and cracking on the wall, whether the waterproofing and brushing treatment of the wall is qualified, etc., if there are problems, it is necessary to rectify and then pave the tiles (this is something to pay attention to both for vitrified tiles and porcelain tiles).

2. The wall must be brushed.

The function of wall brushing is mainly to increase the contact area between the wall and the tile, and the wall must be brushed when the cement mortar is used to pave the tile.

Special reminder: After the completion of the wall brushing, it is necessary to check the quality of the brushing (so that there is no cracking and delamination, burr-like protrusion, and the curing strength meets the requirements), and the tiles can be paved only after the brushing layer is dry.

3. Choose qualified cement and sand and pay attention to the good ratio.

In the process of home decoration, the cement for paving tiles is generally ordinary Portland cement, and the sand is Zhonghe sand. When using floor tiles to pave wall tiles, the mixing ratio of cement and sand is 1:2 (compared with 1:1 in the cement mortar used in the paving of wall tiles with porcelain tiles

3).

4. Do a good job of fixing the bottom tiles to prevent the tiles from falling.

When the tile is paved, when the wall begins to be paved with vitrified tiles, it is necessary to determine the level of the tiles, and the vitrified tiles that begin to be paved are fixed and supported by wooden squares to prevent the falling of the newly paved tiles.