How do you get a small hole in the refrigerator blocked?

Clean the small hole in the back of the refrigerator freezer and place it as follows:

Tools needed: thin hose, hot water, large-capacity syringes, dish soap, etc.

1. As shown in the figure below, connect the syringe to the hose, and insert the other end into the drainage hole to pump out the stagnant water and dirt inside.

2. After the hot water is filled, mix some dish soap, use a syringe to absorb the hot water, and then pump it into the drainage hole, stop when the water overflows the drainage hole, and then suck the water out, heat the water into it, and repeat it several times until the drainage pipe is dredged.

3. As shown in the figure below, use the hose to insert the drain hole until the hose comes out of the other end of the drain hole.

4. Fold the bottom cover at the back of the refrigerator, and you can see that the hose is exposed to the drainage hole and is on top of the tray. The hole is cleared.

1.Find a discarded network cable or a thicker wire, remove the cable, and keep only the outer skin.

2.After the refrigerator is powered off, insert the hose into the drain hole, rotate it to dredge it, and then blow on the other end of the hose to help unclog it.

3.Finally, wipe the inside of the refrigerator clean.

A common concern for users of direct-cooled refrigerators is that the freezer compartment is too prone to freezing – sometimes even if it doesn't, there is a lot of water at the very bottom of the freezer.

It is because the temperature in the refrigerator is set too low, and the refrigerator needs to be turned on for a long time. When the refrigerator is cooling, the temperature on the evaporator (a heat exchange component inside the refrigerator, don't worry too much about its principle) will be very, very low. The evaporator of the direct-cooling refrigerator is placed near the inner wall of the refrigerator, causing the temperature to become very low.

When the stagnant water encounters the ultra-low temperature of the evaporator, it will freeze.

Some people say that when the refrigerator freezes, just turn up the temperature of the refrigerator. This does solve some problems, since it is possible for stagnant water to evaporate before it freezes – water evaporates much faster than ice sublimates. But this does not solve the problem at the root, after all, it is impossible for a refrigerator to be designed to withstand temperatures that it cannot withstand on its own.

This small round hole is the drain hole in the refrigerator. Both sides are tilted towards the small round holes so that the water generated on the inner wall of the refrigerator flows to the small round holes, just like the floor in the bathroom is tilted towards the floor drain. (The temperature of the wall of the refrigerator room is low, so the water vapor is generally condensed into water on the inner wall.)

A hose is attached to the drain hole that leads directly to the evaporator, where a plastic or metal tray is placed for water. The water in the refrigerator is stored after it flows to the plates, and when the refrigerator cools, the compressor heats up. The heat accelerates the evaporation of water from the plate, so although we haven't cleaned the plate, it has never spilled water.

How to deal with the small holes blocked in the refrigerator: 1. Close the refrigerator, empty the food in the refrigerator, leave the refrigerator door for a period of time, and melt the ice in the drain. 2. Remove the baffle on the back of the refrigerator.

3. Use a bicycle pump to dredge. 4. In the case that the water in the water tray will not flow to the refrigerator motor, pour out the debris washed down from the water tray and water, and then install the backsplash.

If the ice plug is washed with hot water, the ice will naturally pass. If it is impurities or dirt, use a soft stick (such as a piece of wire) to pass it through.

If it is clogged by debris, you can use a single-core power cord or other tools to unclog it. You can also unplug the power plug first, then move the refrigerator away, remove the cover under the back of the refrigerator, and pull out the water box above the compressor, so that you can poke up from the drain here, and you can poke the debris inside.

If there is no debris in the drain hole, it is the ice inside the drain that is causing the blockage.

This situation is either caused by the temperature setting of the refrigerator room is adjusted too low, and the temperature setting of the refrigerator room should be adjusted between 4-8 degrees. If it's a mechanical thermostat, just turn the digital gear down.

If the temperature of the refrigerator is within the normal range, it is the quality problem of the refrigerator, the foaming quality of the insulation layer at the drainage hole is poor or the coil is too close, and the manufacturer can be asked to return or exchange it during the warranty period.

During the warranty period, you should ask for after-sales open back repair, rearrange the drain pipe, keep it away from the freezer and then foam it, and finally install the back plate, so that the repair is the most effective.

After the warranty period, it can also be restructured, the method is to find a thicker power cord, peel off the outer skin to expose the core, cut off the power supply of the refrigerator, remove the refrigerator to remove the cover under the back of the refrigerator, and then pull out the water box on the compressor, and insert the power cord core from the drainage hole above the compressor until it is exposed from the drainage hole in the refrigerator. The other end of the power cord bypasses the installation position of the water box, peels off the outer skin longer, and then tightly wraps the wire core around the high-pressure pipe on the right side of the compressor, which should be wound a few more times. Then install and reset the water box.

In this way, when the compressor is working, the high temperature of the high-pressure pipe is conducted by the power line to the drainage hole of the refrigerator room, where there will be no freezing, so that the defrosting water can be discharged smoothly without water accumulation.

Clean the food in the refrigerator, then put a basin of boiling water, and in about 15 minutes, the small holes in the refrigerator that are blocked by ice will be unblocked.

Take out the food, unplug the socket, and wait for it to melt, if it still doesn't work, you can use a syringe to inject warm water into the small hole to achieve unblocked.

Hello! Dear, I'm glad to answer your questions, your questions have been received, and you are consulting the relevant information, please wait!

1.Turn off the power to the refrigerator, then take out all the food in the refrigerator and leave it for a while to melt the ice in the drain. 2.

Remove the flap in the refrigerator. 3.Use a thinner tube to unclog it.

4.After ensuring that the water in the water tray does not flow into the refrigerator motor, you can pour out the debris washed down from the basin and water, and finally install the baffle.

The small hole in the refrigerator is clogged with the solution:

1. The small hole in the refrigerator is blocked, if the blockage is caused by the residue in the drain pipe, you can cut off the power of the refrigerator first, and then use a thin wire to remove the blockage in the water pipe.

2. Turn the refrigerator off. Then see what is blocking the refrigerator, and after emptying the contents of the refrigerator, you need to leave the refrigerator door and leave it for a while. This is done so that the ice in the drain can be melted.

During the dredging process, the dredging effect of heating the brine is doubled.

The refrigerator should pay attention to the following issues during daily use:

1. For every 5% increase in the temperature around the refrigerator, the power consumption inside the refrigerator will increase by 25%. Therefore, it should be placed away from heat sources as much as possible, and it is better to ventilate and shade the place.

2. Control the amount of food stored in the refrigerator, first of all, it should not be too little, if it is too little, the internal temperature of the refrigerator will be too low will lead to a short-term power failure, and the temperature of the refrigerator will rise and heat; The second is that the food should not be too much, if it is too much, it will cause the refrigerator to be overloaded, which will cause the refrigerator to heat up.

Tools Raw materials

Toothpicks, syringes, infusion tubes.

1. Open the refrigerator door and find the location of the small hole, if you find a lot of water, it means that the drainage hole is blocked.

2. The location of the drainage hole of each refrigerator is different, use a small toothpick or a small bamboo stick to get through, if the blockage is not very bad, it can generally be opened.

3. If it can't be opened, find a syringe, cut off a section of plastic infusion tube, put the plastic infusion tube on the syringe, insert the hose into the small hole, and suck out the water inside.

4. After sucking the water out, fill up a syringe with water, drive it into the small hole, and try to see if the drainage hole is open.

5. If the water does not overflow, it means that the drainage hole is open, then clean the refrigerator, and wipe the refrigerator after washing.

It's very hot right now, so many families actually use refrigerators. But if there is a blockage in the small hole in the refrigerator, we must solve it as soon as possible. If the small hole in the refrigerator is blocked, we can let a professional master dredge it.

Therefore, we should have to buy a big brand refrigerator, so that the after-sales service will be better.

When buying a refrigerator, it is equipped with a small stick that prevents small holes from clogging, you can find out if there is one in the refrigerator, and if there is, you can use it to get through. If you don't find it, use a small stick with a non-sharp top.

When the small hole in the refrigerator is blocked, first pull out the stopper, and then rinse it with water.

Just find a slender wire that leads from the inlet end of the hole to the bottom.

Take a small medical pair of the same type, and reach in to take out the blockage and throw it away.

1. First of all, you can observe whether the dirt causes the hole to be blocked. At this time, you can find a thicker syringe without a needle, and then connect the front end of the syringe to the small hole of the refrigerator, and then use the syringe to suck the stains or sewage in the small hole out. 2. Then put some detergent in the warm water, then use the syringe to suck the warm water into the small hole of the refrigerator, and finally pump out the water.

3. Cycle and operate several times until the sewage is cleaned up. Related knowledge popularization: 1. There are actually a lot of inconspicuous dirt inside the refrigerator, and it is easy to be ignored by users.

Therefore, it is advisable for the user to clean it regularly, and it is best to clean the refrigerator thoroughly every once in a while. If you don't know how to operate it yourself, it is best to ask a special cleaning staff to deal with it, and disassemble the refrigerator for systematic cleaning, so that the cleaning will be more thorough and clean. 2. If the small holes of the refrigerator are blocked, it is best not to use the wire to clean it at the first time.

Because the wire is sharp and hard, it is easy to scratch the inner wall of the refrigerator. And if you use too much force, it may damage the small holes of the refrigerator, which will affect the normal use of the refrigerator. 3. For the sake of safety during the cleaning process, it is better for the user to unplug the power of the refrigerator first, which will be safer.