What is the method of putting putty indoors, how to drape it, and what are the steps

Specific steps: 1 Remove the dust on the original wall 2 If there is a place where the skin has fallen off, take a putty knife to clean it 3 Scrape the putty where it needs to be repaired 4 Beat sandpaper 5 Mix brand latex paint with 10%-15% water and stir well 6 Brush the wall Technical points: 1 If you originally brushed lime or paint, and now you want to paint latex paint, you must first remove the original wall and scrape the putty again 2 If you want to paint a colored room, you can directly buy latex paint with color, if you redeem it yourself, you must redeem it at one time, otherwise there is a color difference, of course, The gradual color difference is also a decorative effect,-- if you like 3 The quality of the roller brush must be good The hair quality is moderate The density is even, which affects the stucco effect 4 Brush the ceiling first, then the wall 5 Be sure to dry it for the first time and then brush it again (hehe, I have a lesson, I'll brush it if it's still wet, and bring the wall skin down) 6 Use force evenly 7 Brush the light color 2 times, if you want a strong color, you have to brush it 3 times to be even Remarks:

Don't forget to cover the floor with newspapers and disposable plastic tablecloths, and bring an eye protection Steps to paint: 1. Polishing 2. Scraping putty 3. Brushing primer 4. Topcoat 5. Polishing.

1. Remove the floating ash on the wall, 2, white cement, glue, Nizi leveling 3, scraping putty 4, sandpaper leveling 5, scraping putty 6, sandpaper leveling, detailing 7, latex paint.

If there is plasterboard on the wall or top, first sew it with masking paper. After finishing, put anti-embroidery paint on the iron nails on the wall. After the preliminary work is completed, first use gypsum mixed with 801 glue or diluted white latex for leveling.

Then the first pass of putty is leveled, and after drying, the second pass of putty is carried out. Sandpaper is sanded after the second putty leveling to ensure that the wall is flat. Finally, the primer and topcoat are painted.

How to use putty powder: 1. Add water to thicken, the water-cement ratio is 1:3, and it can be used after standing for 5 minutes.

2. The wall must be smooth, solid, free of oil, floating ash and other dirt. The peeling, hollowing, and chalking parts must be removed. 3. Usually scrape twice, and the second coating can only be constructed when the front coating is dry.

4. After the putty is dry, polish it with 320 or 240 sandpaper, and paint or paste the wallpaper as soon as possible. 5. Each kilogram of putty can be about square meters (two batches) of flat wall. Precautions for putty powder:

1. When storing, pay attention to waterproof and moisture-proof. The storage period is six months. 2. The construction temperature is above 0, and the putty powder should be used within 4-5 hours after being adjusted into a paste to avoid deterioration for too long.

Putty is what we value when we decorate the wall, and we all value the effect of putty when we decorate. Because everyone doesn't know about the decoration, everyone doesn't know how to proceed. So do you know what details you need to pay attention to when applying putty?

How to apply putty.

1. Clean the base layer: concrete or plastering walls, roofs, columns and plate joints must be carefully cleaned, and there shall be no dust, clay, splashing foam and oil stains. The plastering layer is dry and firm, the hollow drum part has been repaired, and the dust, dirt, splash and mortar flow marks and other debris remaining on the plastering layer are removed and swept away.

2. Scrape the yin and yang angles: When scraping putty, the yin and yang angles are required to be clear and smooth. The yang angle is repeatedly extruded by the aluminum alloy rod against the rod; The yin corner is operated with a special tool to make it clear and straight.

3. The thickness of the first putty is controlled at 4 5mm, which is mainly used for leveling, and the construction is carried out in turn parallel to the direction of the wall. It is required that it cannot be left behind, and the end must be closed neatly.

4. Ground grinding: try to use finer sandpaper, generally softer putty (such as 821) with 400-500 sandpaper, harder texture (such as wall lining, easy to quack) with 360-400 is better, if the sandpaper is too coarse, it will leave deep sand marks, and the paint can not be covered. After sanding, the wall must be thoroughly cleaned to avoid too much dust and affect the adhesion of the paint.

The concave letter allows the opening convex difference not to exceed 3 mm.

5. The thickness of the second putty is controlled at 3 4mm, and the second putty must wait for the bottom putty to be completely dry and polished for construction, parallel to the short side of the room with a large plate for full batch, and at the same time, when the putty 6 7 is dry, it must be calendered and repaired with a rubber scraper to ensure that the surface layer is smooth and clean, the texture is straight, and the color is uniform.

Precautions for applying putty.

1. When the base absorbency is strong, it should be sealed with a primer before scraping the putty, so as to avoid the rubber in the putty being too absorbed by the base layer and affecting the adhesion of the putty.

2. Master the inclination of the tool when scraping and applying, and use even force to ensure that the putty is full.

3. In order to avoid excessive shrinkage, cracking and falling off of the putty, do not be too thick at one time, and the thickness should be appropriate according to the characteristics of different putty.

4. Do not scrape back and forth too much, so as not to roll the skin, fall off or extrude the slippery rubber in the putty, and seal the surface is not easy to dry.

5. According to the performance of the coating and the condition of the base layer, select the appropriate putty and scraping tools, when filling the holes and cracks of the base layer with a putty knife, press the blade with the index finger, and press the putty into the defect forcefully.

What we need to consider when we apply putty is its details, so it is also important to learn how to do it. The above is the method and precautions for applying putty introduced to you, and this is the end of it.

For general home improvement, you can take the following steps.

First of all, check whether there are hollows and cracks in the base layer of the wall, and carry out effective treatment first.

Secondly, for the yin and yang corners and template joints of the wall base, gypsum or white cement can be used to make up and smooth the leveling.

Finally, batch putty, can be used interior wall commonly used finished putty, batch three or four times, each time after drying and then batch again, each time the thickness is not easy to exceed 2mm, if you want to pursue the yin and yang angle, flatness is better, you can use gypsum for the base wall before the large ups and downs of the wall smooth, for the yin and yang angle to spring the line, the angle and then batch.

Hope it helps!

There are five steps. The first primer putty, then the second putty, primer, the first latex paint, the last latex paint, the general primer household does not need to be engaged.

Wall putty is to paint a layer of putty on the wall to beautify the wall, fill the cracks, and level the wall. The correct way to put putty on it is as follows:

1.Preparation: Clean the walls to make sure they are dry, smooth and free of impurities. If there are cracks in the wall, they need to be filled first.

2.Choose the right putty: Choose the right putty according to the material of the wall and the purpose of application. Common ones are gypsum putty, polymer putty, etc.

3.Pour the putty into the basin: Pour the putty into the basin, pay attention to the consistency of the putty, you can add the appropriate amount of water to dilute as needed.

4.Wall scraping putty: Resistant refers to using a scraper to evenly apply putty on the wall, with uniform strength and moderate thickness, mainly applied to the protruding parts and cracks of the wall.

5.Trim the wall: After the putty is dry, use sandpaper to trim the wall to ensure that the wall is smooth and smooth.

6.Spraying latex paint: After the application is completed, it can be painted to achieve a better effect.

The above is the correct way to drape putty on the wall. Before applying putty, you need to prepare the wall and choose the appropriate putty material, and pay attention to the strength, thickness and evenness of the application. Finally, it is allowed to dry and then trimmed and painted.