Why do many people do waterproofing their bathrooms several times?

New house decoration, we all know that waterproof is essential, especially the bathroom this moist and watery space, once the waterproof effect is not done so downstairs I lose money, gains and losses are considerable, I would rather spend more money and spirit here when decorating, and do not rework compensation afterwards.

What we know in the bathroom is to do waterproofing, tiling, floor drains and other hard decorations, among which waterproofing is particularly important. The reason why the bathroom will be waterproofed twice, one is because the buildings in the city are not better than the self-built houses in the countryside, and the family lives in a house instead of a house, and the other is that some developers will do a waterproofing but it is inevitable that there will be a leak or the quality is not up to par, so just in case the teacher will do another layer of 2-3 cm cement mortar maintenance layer, and finally brush the waterproof, that is, the secondary waterproofing.

However, before doing the second waterproofing, what must be done is to dispose of the base layer cleanly, there can be no scraps of paper, if it is uneven, it must be filled with cement mortar, because the waterproof layer is like a thin plastic paper, in the situation of leveling will not present the situation of stagnant water, and it is not easy to destroy the waterproof layer, especially need to pay attention to the waterproofing of water pipes, floor drains, wall corners and other joints must be meticulous.

To make waterproof coatings in the bathroom, a lot of preparatory work must be done in the early stage, of course, these procedures are necessary, and they are also laying a good foundation for making waterproof coatings. After all, the request for waterproof coating is very high, the wall, the air is uneven, or there are cracks and are not lubricated, which will affect the back of the waterproof coating, bathroom wall, air demand leveling disposal, with air leveling plastering two-in-one mortar, the average plastering wall air smoothing can be.

Of course, even if the waterproof layer is done, it cannot be careless, and in the end it needs to be maintained. In the eyes of laymen, what needs to be maintained is the cement air and the tiles that have just been paved, but in fact, as long as it is done manually in the later stage, it is maintenance, so that there is a process of compliance between them and there is no longer a phenomenon of crowding out of each other. Therefore, 24 hours after the waterproof brushing is completed, it should be covered with a damp cloth or sprinkled with water until it is completely boring and has no cracks, and finally the waterproof experiment can be done.

The most important reason is that for the sake of insurance, if the bathroom waterproofing is not done well, it will be very troublesome to finish the decoration at that time.

Because this is done to better ensure waterproofing, some waterproofing is more difficult to do, so this situation will occur.

It may be that you bought a fake waterproof material, or you may have done it in the wrong way in the process of applying the material, or it may be that the water pipes are not connected properly.

The family's washing is all done in the bathroom, so there is a lot of water. In order to live more comfortably, there will be no water leakage. So the waterproofing will be done very seriously.

How many layers should be made for waterproofing in the general bathroom? If there is anything you need to pay attention to when brushing, let's take a look. When waterproofing the toilet, you should first treat the corners of the wall and around the pipes.

The mouth of the pipe needs to be made of special materials, and the 20 centimeters from the ground to the wall should be made of a somewhat ductile material. The walls are covered with ordinary materials. Generally, the waterproof surface of the bathroom is about 30 centimeters.

In the bathing place and wash basin, it is best to do one meter eight directly, and when waterproofing, it is brushed twice, not twice in the traditional sense. As long as you brush it carefully, you can do it all at once. Generally, the waterproofing of the bathroom needs to be brushed twice, one layer is brushed when backfilling, and then brushed again after filling.

When brushing, once horizontally and vertically. The plain cement pie mortar is to make the waterproof layer more strong and will not break in layers. Generally, the bathroom is waterproof, and it should not be too thick when brushing, otherwise cracks will appear.

When you don't get the material, you should stir it first, so as not to precipitate, otherwise it will affect the effect. Roll it several times when brushing, so that no bubbles appear. The thickness should be moderate, too thin or too thick, if it is too thin, it should be repaired.

Generally, the toilet is dustproof and water in the morning, and after the first time it is completely dry, check the quality of the project. Then do a closed water test, and start backfilling when there is no problem. After the substance is dry, it can be brushed for the second time.

When brushing, you should brush horizontally and vertically. In this way, the waterproofing of the entire toilet will be very tight. The closed water test must be done so that it can be used safely in the future.

The general toilet waterproofing practice has been clearly introduced, and it needs to be brushed twice in order to be stronger. After thoroughly drying every time you brush, proceed to the next step. The coating should not be too thick, otherwise cracks will appear on the surface, which will also give an impression of the waterproof effect.

In my country, why do some people say that the bathroom should be waterproofedHow many times? The answer provided by yourself: The bathroom to do waterproof architectural coatings, at least three times to do it, according to this procedure, the bathroom to do waterproofing will appear quality assurance.

Everyone is very familiar with interior decoration, needleAlthough the total area of the toilet is not very abundant, it involves many items, which are more complex decorative designs, far from being as simple as other areas, the bathroom sounds very easy to do waterproofing, there are certain difficulties in doing waterproof materials, changing the water, transforming the circuit wall to make a concave groove reinstallation, and each program process is sufficient for waterproof materials. Do moisture-proof two, bathroom waterproof architectural coatings, do a few times is very correct, not to mention the difficulty coefficient of waterproof materials, the provisions for each step are very high, such as water change, circuit transformation wall has different degrees of damage, pre-embedded, drainage port parts are very critical, especially in the key point position is not delicate, even if three waterproof materials, it is very likely to occur, leakage, water seepage and other conditions. Far more than that, there are also a series of decorative designs at the back.

The moisture-proof of the bathroom should be done several times, which means that the moisture-proof must be brushed several times. Personally, I think it should be divided into two processes: the first process is to brush the root of the pipeline, the foot of the wall, the root of the exhaust flue and other parts, and those parts must be brushed three times in advance.

The second major process is to prevent all roads and walls from moisture on a large scale, and I personally think that it needs to be brushed at least three times. Therefore, my final answer is that the moisture-proof of the bathroom actually only needs to be done once, and in the case of a waterproof project here, it is necessary to ensure that everyone paints the waterproof material at least three times or even more than three times. In this way, we can ensure the quality of the construction of the waterproof project in the bathroom.

The third irrigation test means that all the wall tiles and floor tiles in the bathroom have been pavedSubsequent irrigation test. At this time, most of the small bathroom decoration has been completed, and the last irrigation test can be done at this time. The purpose of this irrigation test is to test the final practical effect of our waterproofing, in order to avoid the destruction of the bathroom decoration project in the middle and late stages of the bathroom that has been realized, the moisture-proof should be done several times, the home furniture jar according to the detailed introduction of the whole process of all bathroom decoration, the personal opinion drawn at the end is that the bathroom only needs to be waterproofed once, this time at least three times to brush above, in addition to the proposal to do a good job in the irrigation test.

Bathroom waterproof architectural coating, at least three times to do, according to this procedure, bathroom waterproof quality assurance. Everyone is very familiar with the interior decoration, for the bathroom decoration to do moisture-proof, there are not many people who really grasp it, although the total area of the toilet is not very abundant, but it involves many items, are more complex decoration design, far from being as simple as other areas.

Because if the bathroom waterproofing is not done well, it will need to be reworked many times.

The waterproofing of the bathroom must be done by a professional master, and the waterproofing of the bathroom must be dealt with, or it will be used in the future, there will be great hidden dangers.

Waterproofing is the key project of home decoration, and it is also the answer to the floor pants that are more likely to have problems in the decoration, a little careless, it may cause serious problems of water leakage and accumulation, which is annoying, so how many times does the bathroom waterproof? Let's take a look at how many times home improvement waterproofing is generally done!

First, home improvement waterproofing is generally done several times.

1. The general home decoration waterproofing is the kitchen and bathroom waterproofing, the balcony waterproofing, the bathroom waterproofing, first deal with the corners and the periphery of the nozzle, use special materials around the nozzle, make a slope with the plugging king at the corner of the wall, brush the ground and the wall height of 20 cm with flexible materials twice, and the wall is made of universal rigid materials, and the surrounding walls need to ensure that the height of the painting is not less than 30 cm.

2. If there is a shower, the height of the waterproof paint should not be less than 150 cm and about 180 cm when the shower faucet is installed and the adjacent wall is installed. The waterproof stove is generally painted twice, and it cannot be said that it is twice to be brushed twice, that is, the waterproof paint is applied twice each time. As long as it doesn't leak once, you don't need to do it twice.

Second, is it enough to do the bathroom waterproofing once?

1. Do it twice.

When the bathroom is decorated, it is generally necessary to do waterproofing 2 times, mainly before the backfill, and the second time is after the backfill. (cement + waterproofing agent), horizontal and vertical, brush 1 time each. Note:

The purpose of the brushing mortar layer is to make the base surface and the waterproof layer firmly bonded, without delamination and without falling.

2. Repeatedly. Evenly and densely brushed on the base surface, each brush should not be too thick, or it is easy to appear layering, and it is not easy to dry. When brushing, it should be noted that if the paint (especially the primer) has precipitation, it should be stirred evenly in time, so every time the dipping material is entered, stir a few times at the bottom of the barrel to avoid precipitation.

The coating should be as uniform as possible, and there should be no local deposition, and it is required to roll the brush several times so that there are no bubbles between the paint and the base layer, so that the bond can be firm. Each layer of coating must be based on the specified amount of material, must not be too thick or too thin, if the thickness of the waterproof layer is not enough, then you can consider the wisdom of the additional coating or several layers. During the break or at the end of the construction, all tools and work clothes stained with paint should be washed with water in a timely manner.

Otherwise, it will be difficult to clean the paint after it has dried.

3. The second time.

The second brush after backfilling, this time horizontal and vertical brush twice, but also to do water injection experiments and other waterproof tests on it, check whether it is qualified in advance, so that the decoration workers can rework, so that they will not be pitted, or cut corners. If you don't know how to inspect it, then you can hire a professional to do it, which can also save you a lot of trouble.

The bathroom is an area of home life where water is used more frequently, and it is also a more humid part of the home, so waterproofing is very important for it. If the waterproofing is not done well, it is very easy to get wet and leak. So, how many times do you do bathroom waterproofing?

What should I pay attention to in the waterproof construction of the bathroom? Let's find out together.

Bathroom waterproofing is generally done 2 times, the first time is carried out during the construction of the bathroom, that is, before the backfill. However, due to the destruction of the original waterproof facilities when taking water and electricity, it is necessary to do waterproofing again before tiling. When the bathroom is waterproofed, it is necessary to pay attention to the uniform coating, and there can be no local deposition, otherwise the bond will not be firm.

Precautions for waterproof construction of toilets.

1. When choosing waterproof materials for toilets, we must pay attention to its environmental protection, as far as the current market situation is concerned, there are waterproof materials of various qualities, and there are many differences. Therefore, when buying and choosing, you must pay attention to choosing a well-known brand and an environmentally friendly material that is suitable for home decoration.

2. The areas that need to be waterproofed in the home are mainly bathrooms and balconies, while the waterproofing above the second floor is mainly to prevent water leakage downstairs. For new houses, the high incidence of water leakage is between 3 and 5 years after moving in, if the bathroom is often soaked in water after moving in, then it will take 3 to 5 years of saturation after water leakage, and then it will leak downstairs.

3. When operating the bathroom waterproof, we must pay attention to some details, and it is best to make the process a little outside. In addition, waterproof materials are mainly divided into ordinary type and flexible type, it is recommended to choose flexible waterproof materials, especially for 20-storey houses, because after a long time, the house will have a little displacement, if you use flexible waterproof materials, there is a good tension to prevent the house from leaking.

Article summary: The above is all about how many times the bathroom waterproofing is done and what needs to be paid attention to in the waterproof construction of the bathroom, I hope it will help you. If you want to know more about it, please stay tuned to Qeeka Home.