How many times do you need to apply waterproof materials when making bathroom waterproofing? What ar

How many times do you need to brush the waterproofing project? What are the requirements for brushes? In fact, here we use waterproof paint when we are waterproof, and the waterproof paint should be brushed several times, and ask what are the requirements.

I'll be on the following house miscellaneous waterproof paint application times and smear requirements. Confirm that the water-repellent coating is applied evenly. Because when we are applying waterproof paint, we can use a brush or roller to apply paint on the waterproof walls or floors.

Any paint is applied once or twice, and the paint is difficult to uniformly. Therefore, some empirical data shows that three coats of waterproof paint are the most reliable. Of course, the more you draw, the better.

It is determined by the thickness required by the waterproof coating coating. All waterproofing paints are completed, and there are corresponding requirements. One of the most important data in these requirements is the thickness of the coating.

If we only apply waterproofing paint once or twice, it will be difficult to meet the requirements for film thickness. As a rule of thumb, it takes more than three brushes to ensure the thickness of our coating. Decision on quality assurance of waterproofing works.

To ensure the so-called construction quality is to ensure the effect of our waterproof paint. Based on the experience of common waterproof paint brushes, we apply the floor one more time, the middle one more paint, and the last side paint. The method of applying it three times is the best measure to ensure the quality of waterproof paint.

So it's usually a triplicate approach.

The coil is firmly bonded, and there is no hollowing, blistering, and warping. Through the corners and waterproof ring surface of the pipe, the built-in structure is reasonable, tightly gambling. Asphalt workers should wear work clothes, wear safety helmets, masks, gloves, canvases, foot covers and other labor protection supplies, and apply protective oil on the front of the operation and on the exposed **.

When the basement is not well ventilated, ventilation measures should be taken in the packaging ring to prevent the volatilization of organic solvents and poisoning the operator. When the hot melt method is constructed by flame heating, it must be heated evenly within the width of the coil that needs to be heated, and the insufficient heating or excessive heating of the base acceptance spray (coating) will affect the quality of the paste.

After treatment, on the base layer, according to the tiling direction of the coils, the packing lines of each coil are protruding to prevent skewing. Later, when the bunk is laid, the line should also be played to the place where it has already been laid. In the case of two-component adhesives, the mixing ratio should be measured correctly, mixed well, and applied within the specified running time.

Cement paint should be evenly applied, no leakage, no accumulation. Depending on the performance of the adhesive and the requirements of the construction environment, it can be applied immediately after painting or after the solvent has evaporated. Therefore, it is necessary to control the gap between the adhesive paint and the roll sticker.

The ordinary waterproofing membrane is generally a layer of waterproofing, and the new waterproofing membrane is multi-layer, the purpose of which is to improve the shortcomings of the original material and improve the performance of the material.

Bathroom decoration waterproofing generally needs to do 2 times, the first time is before the backfill, the second time is after the backfill, the first time to do waterproofing will be evenly and densely painted on the base surface, the coating layer should not be too thick, otherwise it is easy to get up the layer, and it is not easy to dry.

When decorating the home, it is necessary to paint the waterproofing of the bathroom three times. The requirement of brushing is to ensure that the waterproof material is completely attached to the wall, and there is no blistering or falling off.

It is best to apply two layers of waterproofing, because it is more secure, and there is no requirement when painting, as long as it does not leave gaps.

Polymer polymer materials: the same has good plasticity and ductility, and there is no color and taste, which is very environmentally friendly and healthy. But it also has a flaw, it can't collide with anything, otherwise it will cause the waterproof membrane to crack and seep water.

The waterproof material of this kind of toilet is relatively high. The traditional floor tile paving is not creative, although it can have basic applicability, and there is no shock at all. And the relatives' house is not the same, the special tile is paved with metal material bricks in the middle, and the appearance is several times higher, needless to say, the actual effect is more attention-grabbing.

Instantly elevate the restroom by multiple levels. It's okay to have young people living in the house, but for the elderly and children, the surface of the water-stained floor tiles is very prone to falls and falls, which increases the safety risk. The design scheme of this kind of metal material floor tile patchwork pavement, and the convex and concave design scheme of the surface layer, improve the sliding friction and is not easy to fall.

The bathroom can be made of waterproof raw materials can use acrylic, and his odorless is achieved through the conjunctivitis of the raw materials to achieve the purpose of moisture-proof, which has very good plasticity and ductility. It is also a very good raw material for toilet waterproofing.

But the engineering cost of this raw material can also be based on new polymer cement. If there is a water leakage, the leakage position must be solved until there is no water leakage, and then brush with high permeability crystalline waterproof coatings, including polyurethane, epoxy resin glue, and silica can be used, but clean the brush surface as much as possible before brushing, and then apply a few more. Polyurethane materials have very good viscosity and have strong follow-up to the surface of the wall after painting.

In places with high humidity such as toilets and cooking rooms, if the waterproof coating applied is weakly viscous, it is very easy to crack and lead to water seepage. The surface of this waterproof coating is very firm, high flexibility, strong flexural and elongation, strong resistance to decay and structural expansion deformation, even in the case of poor standards, there will be no cracks and flow, anti-aging, wear resistance, and has a long service lifeBut there is a smell, gray-black is not environmentally friendly, and it is not good-looking.

You can choose waterproof coatings, you can choose tiles, these can be waterproofed, and generally waterproof paints need to be applied three times.

I think it's best to use polyurethane paint, which is usually brushed about twice.

In the process of bathroom decoration, waterproofing is very important, the bathroom should be double-layer waterproof as much as possible, and you can go to the market to buy some better waterproof materials.