What is the number of 50 tweeter cables? How much is the 50w voice coil of the tweeter, how much is

It depends on the specific situation, under normal circumstances, No. 3 to No. 5 are completely without any problems, and the use effect is also very good, so it is okay in this regard.

50 tweeter cable with No. 3 to No. 5 are OK, these numbers are relatively thick, all aspects should meet the requirements.

The tweeter uses the No. 3 line, connected to the current transformer, and the product will actively turn on itself.

The number of 50 tweeter cables should be about three.

The 5th and 8th can be used, it's very simple.

This speaker cable is enough for Line 5.

It's not that the thinner the better, and the silver wire will be slightly faster.

But the point is to match according to all car audio configurations and the environment in the car is the most correct!

50 What is the first number to use to seduce love? I don't know much about this, how many lines are used for horns? I don't know, but if you want to know, well, people who often use wires can only know if they contact people in telecommunications.

It depends on the specific situation, in general, it is usually within the allowable range of power as much as possible, and the effect is relatively good.

Speaker lineman number borrow you when the tweeter about I'm standing

Because the model you have here should be a 32-inch one.

If the mantissa is different, many times there are different functions.

50 tweeter line ing number 12 line.

The high-voltage wire is generally used in this case, and his function is very high-voltage speaker line, which is generally used in the case of No. 5, and its functions are very complete.

How many lines do you use for 50 tweeter cables, I think this should be used for line 5.

50 tweeter cable with a few numbers, this should use the fourth line.

In the case of tweeter cables, generally speaking, the third line should be used, so you can read his purchasing instructions when purchasing.

If you use a few lines for the 50 high school line, this kind of treble line should be the third line.

Voice coil speaker voice coil according to the needs of low, medium and high woofer units are different, the tweeter voice coil is wound with a very thin wire, including copper wire and aluminum wire, aluminum wire weight is lighter, can obtain better transient response, but in terms of bearing capacity and durability is not as good as copper wire, midrange and woofer mostly use copper wire around the voice coil, and copper wire is thicker to withstand high power, some woofers around two to four layers of voice coil to increase bearing capacity, as for the shape of copper wire is also different, such as circular, hexagonal and rectangular cross section, round wire is most commonly used, Hexagonal and rectangular lines can be closely arranged without leaving gaps, which can increase heat dissipation efficiency and correspondingly improve power carrying capacity. In order to improve the heat dissipation efficiency, some speakers use aluminum or kapton voice coil tubes, and the voice coil is fixed on the tube because of better heat dissipation, significantly increasing the bearing capacity, and more and more speakers are using this material recently. Generally, most of the horns are burned on the tweeter, because its voice coil is wound with a thin wire, can not withstand high power, some speakers are equipped with a protective line, when the input current is too high, automatically cut off or reduce the current to prevent the tweeter from being damaged.

The midrange and woofer voice coils are strong and not easy to burn out, but when the input is too strong, it may cause the voice coil to bottom out or skew.

Regardless of the power, the DC resistance of the voice coil of the tweeter is about 80% of its rated impedance. For example, for 8 speakers, the DC resistance of the voice coil is about 6.6 ohms. Therefore, the measured DC resistance can be deduced from the measured DC resistance.

Yes, yes, it's not what you want, don't be lucky, yes, it's because some of it is when I do it myself. A person Yes......No, my life file search is a person's life

The thickness of the copper wire of the woofer and tweeter coil is: the paper cone of the woofer is large, the vibration frequency is lower than that of the tweeter, and the vibration amplitude is large, so the coil diameter is large, the passing current is large, and the wire diameter is also thick. Eight-inch speaker, voice coil diameter is 40-50mm, six-inch size or sizzle speaker, voice coil diameter is 30-40mm.

The diaphragm of the tweeter is small, the vibration frequency is much higher than that of the woofer, and the vibration amplitude is small, so the coil diameter is small, the passing current is small, and the wire diameter is also thin. We've done it with a voice coil diameter of 127mm, how big is this speaker!

The length of the weld is a question. When welding both ends of the voice coil, the slag should be left with a certain length of wire, which is too tight and easy to use when the volume is large. The high-quality voice coil is braided copper wire at both ends, which is very filial piety and toughness!

Under normal circumstances, electrodeless capacitors are used, but if you want to be louder, you can also use them.

The capacitance capacity of the tweeter in series can be changed to a smaller one, and the minimum can be changed to 2 microfarads. You take the speaker apart and look at it, and there should be a noticeable change. In addition, you can also see if the tweeter has a coil in series at the same time, and if the sound is not ideal after changing the capacitor, you can connect the tweeter coil in series.