What should I do if the wall is peeled, it s quite serious! It s so sad to watch!

If it's really serious, it's recommended to renovate the wall. If you feel troublesome, you can find a professional company to refresh, I think Nippon's refresh service is good, they specialize in renovating the wall. Materials, labor to do all for them, will also help you do a good job of masking and moving, do not have to do it yourself.

I heard that the efficiency is also very high, and it can be done in a few days.

The main causes of peeling are:

1. The stucco layer is hollow;

2. When the wall is painted, the indoor humidity is large, which produces moisture return, which causes the paint layer of the later construction of the wall to peel.

3. The wall is in a humid environment for a long time, such as water on the other side of the wall for a long time, or there are cavities in the wall, and it is damp after rain, resulting in the peeling of the indoor wall.

Solution: In the above case, the processing method is in the following order:

1. Knock off the hollow drum part and repaint the wall, pay attention to the need to wet the wall the day before painting. The thickness of the painting should not be too thick.

2. It is necessary to remove the paint layer, ventilate the room, and carry out the paint construction after the indoor humidity is not very large.

3. Find out the permeable place on the other side of the wall, shovel off the stucco layer, use cement mortar with a higher grade to fill the hole, and paint it. The treatment of the inside of the post-treatment wall is also carried out using a method similar to 1.

The peeling of the wall is that the quality of the material composition is not up to par, and it can only be processed with a batch of ash knives and then rectified from the beginning.

Knock out the peeling area and brush it again! Peeling of the wall indicates that there is a problem with the quality of the material.

You can only shovel off the new brush, and if you do a small amount, you can partially shovel it and repair it.

Large-scale wall peeling requires professionals to shovel off the wall skin and apply primer and putty; Small areas may be repaired by themselves with toothpaste.

For example, perform the following steps:

1. Squeeze an appropriate amount of toothpaste into the container.

2. Add a little water to the container.

3. Mix the two evenly into a paste with a tool.

4. Take a scouring pad and dip an appropriate amount of toothpaste paste.

5. Slowly wipe the peeling position of the wall until the wall skin is moist, and then apply evenly.

6. After treatment, the wall skin is combined with the toothpaste paste and stained to the position of the wall peeling.

7. After the water evaporates, the position of the wall skin will return to its previous appearance.

Most of the peeling on the wall is caused by water seepage You can check it first**infiltration My family also had such a situation before, and the bathroom seeped into the exterior wall Later, a friend recommended a product bought online to solve it.

Finally, spray moisture-proof to prevent moisture from penetrating.

The newly renovated living room, not lived for a long time, the wall peeling, chalking, falling off, will definitely bring a lot of trouble to the owner, will complain that the paint is not good, or the construction workers are sloppy. However, you may not know that in fact, the root cause of wall peeling, chalking, and peeling off is not the surface coating and construction level, but how to deal with the base layer during construction. Red Sails hosting experts said:

For the old wall, the original base putty, paint should be removed clean, some rooms are used in the initial decoration of the wall is 821 putty, this putty is easy to powder, peeling, falling off, but also all shoveled, re-base treatment. First of all, the wall to be decorated must be solid, firm and dry (moisture content less than 10), and secondly, before re-scraping putty, the sealing primer should be applied. Primer can improve the pH of the base wall, improve the strength of the base layer and make the coating have better adhesion to the base layer.

When choosing a sealing primer, you must choose a special primer from a regular manufacturer, and do not use some glue instead of a sealing primer for sealing treatment.

Red Sails hosting experts remind us that the most important step is at the end, which is to scrape putty. Before painting latex paint, you need to scrape the putty twice, the choice of putty is also very important, you must not use 821 putty, you should choose water-resistant putty from well-known enterprises, such as LG 940 water-resistant putty of Xingpai Building Materials Company. This kind of water-resistant putty has high whiteness, good water resistance and high bonding strength, and is a key promotion project of the Ministry of Construction's technical achievements.

After such treatment, the wall is painted with qualified latex paint, and your home life must have no worries.

1. Peeling and cracking of the small area of epidermis. Shovel off the peeled part and the surrounding wall skin, and fill it with the same color paint; If the decoration is brushed with latex paint, it is best to use the same method of brushing glue for the second treatment, which can reduce the color difference between the part and the whole.

2. Large-scale peeling and cracking, you can only shovel off all the paint and putty on the wall, brush the cracked base layer with white latex, paste a good cloth, wipe putty, and so on after drying, polish with sandpaper, and then brush the paint. If the crack is deep, this part should be treated with plasterboard separately.

3. It can be renovated and decorated with wall clothing to prevent the wall from peeling and cracking.

Sometimes we will find that the wall will peel, this time we must deal with it in time, otherwise the situation will become more and more serious. If you want to completely solve the problem of filial piety, you must first find the cause of the peeling. What is the cause of the peeling of the wall?

What should I do if the wall is peeled? Let's take a look at it together.

1. What is the reason for the peeling of the wall?

1. The settlement of the new house leads to the cracking of the wall.

Generally, there will be a process of foundation settlement in a new house for a year or two. During the settlement process, the wall stretches, which will cause wall cracks or wall peeling and cracking. In the process of foundation settlement, do not rush to partially repair the wall, it is best to wait for the settlement period of 1-2 years to gradually stabilize before starting to repair the wall.

2. The wall is heated and expanded.

For buildings with large lighting area and insufficient air circulation and walls directly exposed to sunlight, the temperature is too high, and the water-soluble salt crystals on the surface of the wall cause discoloration, fading, color shedding and even cracking. In addition, the use of air conditioning causes the temperature difference between indoor and outdoor, which causes the wall surface to expand or shrink, and also causes local wall peeling.

3. The developer's construction is not handled well.

When the developer delivers the house, the wall is smoothed with plain ash, and the workers must shovel off the plain ash of the base layer and re-brush the primer when painting the wall. If the workers do not clean the base layer in the decoration, it will cause the wall to peel and crack for a period of time after brushing the latex paint.

4. The wall peels off when it is damp.

One situation is that when the wall foundation is wet, if the paint is painted before it is completely dry, it will cause the wall to be wet and peel off; The second is that in the rainy season rainy season, the air moisture causes the wall to be damp, both of which are orange because the moisture penetrates into the paint surface and causes the paint film to lose adhesion, resulting in peeling and peeling.

Second, what to do if the wall is peeled.

1. Scrape the peeling part and scrape the putty.

If the white wall or bare wall is partially bulging or slightly cracked and peeling, you can remove the problematic place, and smooth the edge of the shoveled part, scrape the putty again, apply primer, and brush again, but there may be a little color difference with the original wall.

2. Strengthen the base layer.

If the wall is peeling and peeling on a large scale, the first thing to think about is whether there is a problem with the bottom layer of the wall. During construction, it is necessary to re-reinforce the base with Gordon Refresh Wall Reinforcement, and then we will take a series of steps such as plaster leveling, applying mesh cloth, brushing primer and painting.

3. Roll brush topcoat covers the part.

If it is a simple fading, it is generally recommended to take the way of a roller brush to cover a new round of primer and a similar topcoat, but before construction, it is necessary to judge the quality of the putty layer of the wall at this time: choose the worst piece of the wall to fade with water and then use a shovel to produce a shovel, if there is no chalking or falling off (indicating that the quality of the original putty layer is better), you can directly use fine sandpaper to polish and smooth the treatment and brush the new bottom of the paint and topcoat.

The reason for the peeling of the wall may be the settlement of the new house, the expansion of the wall by heating, the construction treatment is not good or the wall is damp, after finding the reason, you can take corresponding measures according to the peeling and falling off, and finally do some preventive work for the peeling cause to prevent the same situation from happening again.

Causing the wall to peel and fall off, mainly caused by the poor quality of putty, not enough hardness, too much water absorption, but the putty is not good to absorb water will peel and fall off, generally appear on the body of talcum powder and glue, now everyone uses putty, the thinner the putty scrape more times the effect will be better, too thick will not appear peeling, too thick the consequence is cracking, it is recommended to soak the peeling with water, and then shovel it all, and then use a better putty to scrape two or three times, thin scraping, scrape many times, the effect is good, If you don't want to change the putty of bad quality, you can add white cement and glue to it, and now water-resistant putty is the mainstream in the market. Its main function is moisture-proof and water-resistant; After the batch is hung on the wall, even in the rainy season. There is also no flaking; Because the strength of water-resistant putty is very high.

When moisture passes through the wall, the water-resistant putty does not react with the water. Therefore, there will be no peeling.

The reason for peeling is that the putty is not good, the hardness is not enough, and the water absorption is too much, but the putty is not good at absorbing water before the peeling falls off, which generally appears on the body of talcum powder and glue, but now everyone uses putty, mainly because the quality of your putty is not good, the thinner the putty scraped more times, the better the effect, but this kind of thing will not appear (the painter cannot waste time to help you do so in place) too thick will not appear peeling, too thick The consequence is cracking, it is recommended to soak the peeling with water, and then shovel it all up, Then use a better putty to scrape two or three times, scrape thinly, scrape many times, the effect is good, if the quality of the putty you don't want to change, you can add white cement and glue to it.

If the wall putty layer or paint quality is poor, or caused by aging, the putty layer should be shoveled off, and the putty should be scraped again. If the cement mortar of the base layer is not strong, the wall peeling caused by desanding, it is necessary to reinforce the cement mortar so that it does not desanding and then scrape putty, it is recommended to use the "sand traceless wall desanding repair liquid" to solve the problem of wall desanding, and then do the post-process, otherwise the post-process materials are useless no matter how good they are. Hope it helps.

Peeling may be a construction problem or moisture, putty white cement quality problems, mostly in the construction of the white cement is not left to cause two skins, the combination of inside and outside may be the majority.

When the weather is dry, ask the workers to shovel off the peeling all around, it is best to make a waterproof, if the peeling range is too large, please ask a professional master to deal with it.

You may be talking about a house that has been fanned with dust, and it is usually caused by the fact that he has cut corners when fanning, which can only be done by re-approving the walls.

Hello landlord: It is recommended to first figure out whether the wall skin of the old wall is removed before the new decoration, if the old wall skin is not removed, it can only be the whole re-peel and then scrape the putty, this phenomenon also has a possibility that the first putty is not dry during the construction of the putty scraped the second time, the solution is to shovel out the cement bottom to dry, and then the gypsum is dry and then the construction can be repaired.

See if it is leaking, if it is not leaking, then the original putty is not good, you can only shovel the wall skin and then scrape the putty again, and then paint it.

First, use a shovel to peel the wall surface due to dampness to the cement layer.

2. Clean up the dirt and dust on the construction surface and keep it clean and dry.

3. After that, apply the separator to the cement surface 2-3 times, with an interval of about 3 hours between each time.

Fourth, the separator can play a role in moisture-proof and alkali-proof, to prevent the subsequent occurrence of moisture alkali problems.

5. Use water-resistant putty paste to repair the wall completely after drying the next day.

6. After the surface is dry for 4-6 hours, use sandpaper to polish the wall flat.

7. After the putty paste dries the next day, clean up the surface dust and paint latex paint 2-3 times, with an interval of about 3 hours between each time.

8. Painting latex paint is to make the wall smooth, white, and have no dust effect.

Is the wall peeling and moldy? Teach you a few simple steps, easy to repair, no need to spend money to find someone.

If you just want to touch it up simply, shovel off all the peeling areas, brush the interface agent, scrape the water-resistant putty in batches, and then apply the topcoat.

It should be a leak, and the skin will be shoveled off first. Buy some putty powder and mix well with water and scrape it on. After drying. Just hit it with sandpaper and paint it.

First, the peeling of the wall is mainly caused by the following reasons:

1. The base layer of the wall is loose and pulverized;

2. There are floating ash, oil stains, release agents, etc. on the surface of the base layer;

3. The moisture content of the base layer is too high;

4. Construction in a high humidity environment;

5. The paint is frozen before drying.

Second, the treatment method:

1. Strengthen the base layer;

2. Completely remove debris;

3. Construction below the specified moisture content (10%);

4. Avoid construction in high humidity (85%) environment; Avoid low temperature (5) construction.

The stucco layer falls off, causing the outer wall skin to fall off, that is, when painting the wall, the water glue ratio of the gray sand is not correct, resulting in too much sand, or the outside of the gray sand layer is not combined because it is required to brush another layer of cement paste, resulting in falling off. Wall peeling, that is, delamination of latex paint base layer; This is a headache for residents, and this has little to do with whether there is anyone living there. Why?

Because of the alkali return phenomenon, it will not appear because the family has been inhabited for a long time; As long as conditions are formed inside the walls, what should come will always come. The main reason for the peeling of the wall is that the wall is damp and does not dry out for a long time, causing the phenomenon of alkali on the wall, after the alkali on the wall, the mycelium generated grows outside, and the latex paint film on the surface will hinder the growth of mycelium, and finally the latex paint film will be separated from the base layer and fall off, becoming the phenomenon of peeling.

Loose wall base - the original cement mortar base is loose, and the putty is scraped directly without treatment, which will lead to poor bonding between the putty and the cement mortar layer, and the problem of wall peeling. Or the putty powder is of poor quality and loose texture, and the latex paint grabs the putty layer after the latex paint is painted, and the problem of wall peeling occurs. There is a certain relationship, the house is not inhabited, the dry humidity of the air is not the same, and there is a slight leakage, if it is not dealt with in time, the long-term illness will not be cured into a serious disease, mold, and peeling will be more serious.

You look like putty is not brushed well.

Questions. Renovation in less than a month. This is the case.

The grassroots level has not done a good job.

Contact the original company to rework.

Questions. Is the reason for this on the construction side, or on the renovation company?

The renovation company said that it was the responsibility of the construction party.

Decoration company...

How can it have anything to do with the construction party? This is a clear excuse.

Didn't you sign the contract before, and didn't write the warranty time?

Questions. If the contract is signed, the warranty is two years.

It's still under warranty, it's the wall paint that's falling, it's obviously a process problem with the decoration company, and this must be something they came to rework.

If they still don't want to, you can look at the property and then you can 315 complain to them.

Questions. Ok, thanks for the answer.

Polite, if it helps you, can you please give it a thumbs up? Thank you very much