What is the solution to the washing machine floor drain anti water and anti odor?

1.Generally, the backwashing of the washing machine is due to the blockage of the lower part, which will lead to poor drainage and water ingress after a long time. This is mostly because there is a lot of debris in the pipes of the washing machine, and some of it is discharged into the floor drain and sewer.

Dig them out. Another reason for poor drainage is that the pipes are too long and the outlet pipes are too high above the ground. As a result, the water will be discharged at the same time.

In this case, just cut the tube a little shorter, and remember to cut the bevel to enter the water faster. If your washing machine's drain pipe is twisted, be sure to straighten it.

2.Check the drainage of the floor drain, you can first see if there is any foreign object blockage, and try to avoid changes in structure and installation. Generally speaking, washing machines installed in bathroom spaces are relatively tolerant of this situation, and hair or other small impurities may clog the floor drain with running water from the floor.

Therefore, when using the washing machine in the bathroom, special attention should be paid to avoid the hair entering the floor drain when showering or washing, resulting in poor water flow, serious non-drainage and soaking. The reason is to clean up the clogged foreign matter and then replace the floor drain.

3.Essentially, the floor drain of the washing machine is against the water, because the washing machine drains through the drain pipe connected to the center of the drain, and the limited drainage area leads to concentrated drainage and instantaneous excessive drainage. Therefore, to change this situation, we must start by reducing the drainage and reducing the drainage rate.

Many washing machines have built-in fittings in their drains that regulate the amount of water coming out. This reduces the instantaneous amount of water discharge, reduces the amount of water produced during the drainage process, and does not exceed the limit of floor drain drainage. Although this method drains slowly, it is also a relatively reliable method.

This method is still to reduce the drainage resistance and enhance the drainage capacity.

4.Try to choose a material with a smooth inner wall, which is not easy to retain foreign matter. Such as stainless steel and other metal floor drains.

When the floor drain of the washing machine is turned back, you can refer to the above methods to solve the problem. Ordinary floor drains will not work. There will be a floor drain core in the middle of the floor drain of the washing machine.

A lot of people have removed it because of waterproofing issues. Although it drains quickly, some foreign matter or dirt and odors can damage the washing machine without the filtration of the floor drain core. If the drain pipe is clogged, there will also be an odor and bacteria breeding.

Therefore, in daily life, we should unclog the drain pipe of the washing machine every month or so to prevent bacteria from breeding here and affecting the health of the family.

We can choose the anti-odor floor drain, we can also choose the water seal floor drain, now there are many washing machine special floor drains on the Internet, the sealing is very good, and usually does not leak, we can buy one, you can also buy some floor drain dredging agent, usually we must often pour the floor drain dredging agent into the sewer pipe, and then often replace the floor drain, so it is good.

Buy some dredging agent for dredging, prepare some baking soda powder to pour into the drain, cover the floor drain with some towels after pouring the water, after pouring the water, be sure to clean it with clean water in time, and pour some vinegar into the floor drain.

Dredge the pipeline in time, clean up the foreign matter in the pipeline in time, and spray deodorant, which can ensure the circulation of water and avoid the odor caused by foreign matter blockage.

You can change the floor drain, or you can clean up the debris in the floor drain, which may be that the outlet pipe is relatively high. It could also be that there is a winding.

Floor drains may occur in the washing machine during use.

1. There are debris in the floor drain.

When there is debris in the floor drain, you need to open the lid of the floor drain and clean up the debris with a pipe dredger.

2. The outlet pipe is too high.

The outlet pipe is too high from the ground to cause the water in the pipe to be unclean, which not only has the situation of backwater, but also affects the normal function of the washing machine, so it is necessary to adjust the height of the outlet pipe.

3. The drainage pipe is too long or winding.

If the drain pipe is too long, it is necessary to cut a part of the drain pipe, and if it is a drain winding, the winding part can be restored to normal.

Washing machine is currently a must-have household appliance for many families, because usually everyone's work is busy, when decorating the house, in order to facilitate the washing machine drainage, the floor drain of the washing machine will be reserved, but some people find that when the washing machine is washing clothes, the floor drain will be backwater, what should I do when I encounter this situation? Today, I will explain to you the specific treatment method.

1. How to deal with the backwater of the washing machine floor drain.

If it is because there is a blockage in the floor drain, then you can remove the lid of the floor drain, and then use the pipe lead to know the dredge to stir the pure mountain clockwise, and then stir out the foreign matter inside, and the problem of waterproof floor drain in the washing machine can be solved. If it's because the drain is higher than the drain of the washing machine, then try raising the washing machine a little higher.

Second, is it necessary to install a floor drain in the washing machine?

Because the frequency of use of the washing machine is very high, it is very necessary to install a floor drain, if you do not install a floor drain for the washing machine, then the washing machine drain pipe is drained, it is possible that because the water flow is relatively large, the water in the washing machine will be left directly at home, and after a long time, the drain pipe of the washing machine will emit a relatively unpleasant odor.

3. How to choose to buy a washing machine floor drain.

First of all, you can choose according to the material of the floor drain, the materials currently sold on the market are copper alloy, PVC, ceramic, stainless steel, among which the floor drain of stainless steel is more moderate, and the color is also relatively bright.

The second is to choose a floor drain with a relatively large drainage hole, so as to ensure that the water flow is fast.

In addition, it is necessary to choose a floor drain that can be connected to the washing machine water pipe, which can play a role in preventing odors.

Fourth, why does the floor drain of the washing machine overflow?

1. The diameter of the purchased drainage pipe is relatively small, and there is no way to meet the drainage capacity of the washing machine.

2. There are curves in the drainage pipe, which will slow down the speed of washing machine drainage, resulting in the sewage not being able to be discharged quickly.

3. The drain pipe of the washing machine is blocked, resulting in the washing machine not being able to drain properly.

Now the washing machine is a very popular household appliance, but in the process of use, we will find that the floor drain is backwater, and the pin is carefully checked, and the drainage hole is indeed inserted into the floor drain. So why is this happening?

It is usually caused by a clogged sewer. Take out the drain hole and pour a basin of water into it to see if there is any envy and backwater. If the water comes out, it means that the situation is caused by a blocked sewer. A professional master can be invited to unclog the pipes.

If the floor drain of the washing machine is backwater, the treatment method is as follows:

1.First of all, stop using the washing machine, never continue to use it, and wait until the water is drained before checking.

2.Find the location of the floor drain, check if it is blocked, and if there is a blockage, clean it to avoid water leakage.

3.Check whether there is a problem with the floor drain, and if there is a problem, repair or replace it in time.

4.Check whether the water level sensor and the magnetic valve of the electric silver limb are normal, and replace them in time if there is a problem.

When handling it, it is necessary to pay attention to the following matters:

1.Turn off the power and disconnect the power cord to ensure safety. Never put your hands in the washing machine while it is working.

2.Be careful to wear protective equipment such as work clothes or gloves.

3.The treatment process should be patient and meticulous, avoid negligence, and ensure that the repair work achieves the expected results.

How to take care of your washing machine:

1.Wash the filter and detergent basin in your washing machine regularly to remove dirt and build-up.

2.Regularly inspect the water source pipes for ruptures, aging, etc., and replace them if there are problems and when they are discussed.

3.Regularly inspect the power cord for wear and tear and replace it regularly.

4.Depending on the frequency of use of the washing machine, the rubber seals and the washing machine housing should be cleaned regularly.

5.Pay attention to the amount and quality of the laundry, and do not overdo or overwash the laundry, so as not to put an extra burden on the washing machine.

The washing machine floor drain is backwater, indicating that the floor drain of the washing machine is wrongly installed, and the ordinary floor drain is not suitable for the washing machine drainage of the large flow of cherry blossoms.

The solution, change clothesThree-way floor drain or special floor drain for washing machinesThat's it. Jinchang.

1. Foreign matter blocks the floor drain. Check the floor drain drainage, you can first see if there is any foreign body blockage, and try to avoid changes in structure and installation. Generally speaking, the washing machine is installed in the bathroom space, and the hair or other fine impurities may block the floor drain with the running water on the floor.

Therefore, the key can be removed to clean up the clogged foreign matter, and then the floor drain can be put back on. 2. The drainage pipe is too high from the ground. There is a certain limit on the height of the drainage pipe of the washing machine from the ground, and if the height is exceeded, the drainage will be affected or even impossible to drain.

The water in the pipe is not clean, and the accumulated water will deteriorate and produce peculiar smells in the long run; If the drain is higher than the drain of the washing machine's drain solenoid valve, it will also affect the normal function of the washing machine. In this case, it is necessary to adjust the height of the drain pipe so that the water can be discharged smoothly. 3. Reduce the drainage rate.

The washing machine floor drain is essentially due to the fact that the washing machine is connected to the center of the floor drain through the drainage pipe, and the limited drainage area causes the drainage concentration and instantaneous drainage to be excessive. Therefore, to change this situation, it is necessary to start by reducing the amount of drainage and reducing the drainage speed of Zhiliang regret.

Washing machine floor drain anti-water treatment method:

1. Water discharge and dredging method.

Check it first to see if the floor drain is blocked, if it is blocked, you can clean up the blocked place first, and then put water into the floor drain, and wait until the height is about the same, you can find the location of the water trap according to the water storage situation.

2. Pumping and dredging method.

Pump dredging method is a more common treatment, when dredging, you can put the hose of the pump into the drainage pipe, and then seal the drain, and then put enough clean water in, use this space to quickly pump air into the sewer, so that it can be dredged quickly, and there will be no backwater.

3. Soda and vinegar dredging method.

If the blockage causes backwater, you can try to dredge it with high-concentration vinegar and cooked baking soda. First put the baking soda powder into the floor drain, and then pour the vinegar into the drain, at this time, the baking soda powder and the strong vinegar together will produce a very strong chemical reaction, and some of the oily things in the pipe can be removed.

4. Log dredging method.

To put it simply, it is to put a piece of wood with a diameter similar to the sewer pipe near the floor drain, and then release the water, constantly pumping the log up and down, so that the dirt in the pipe will be sucked away.

The cause of the floor drain backwater.

1. It may be that the floor drain is blocked by garbage, sundries, etc., resulting in backwater.

2. It may be that the drainage pipe is blocked by debris, and there is backwater.

3. It may also be that the drainage pipe is not installed properly.

4. It is also possible that the air pressure in the pipeline is too large, which causes the phenomenon of backwater.

If the floor drain of the washing machine is always smelly, you can fill it with sand with a plastic bag and press the plastic bag on top of the floor drain when the washing machine is not in use. Because the sand will show an extended state, it fits closely to the floor drain, and it can be plugged tightly, so you don't have to worry about the smell wafting out.

Other solutions:

1. To replace the floor drain, choose a floor drain with good sealing, and it is best to choose a special floor drain for washing machines.

2. Cover the floor drain with a wet towel to prevent the smell from spreading around.

3. Use deodorant and pay more attention to cleaning.

It is very common for washing machines to drain old and back-water, especially after a period of use.

Reason 1: The drain pipe is blockedThe drain pipe is the pipe that discharges the water discharged from the washing machine, and if the drain pipe is blocked, the most likely thing is the reverse water phenomenon. This is because the water is blocked on its way out, causing the water pressure to increase, which causes the water to flow in the opposite direction.

Solution: Use a professional pipe cleaning tool to clean the drainage pipe; Or you can use some detergent to clean the dirt inside the pipes and avoid clogging the pipes.

Reason 2: Improper installation of drainage pipesWhether the drainage pipes are installed correctly will also affect the drainage effect of the washing machine. If the drainage pipe is bent down, the water flow will not be easy to drain out, which will also lead to the appearance of anti-water.

Solution: If it is caused by improper installation of drainage pipes, you need to find a professional to reinstall the drainage pipes.

Reason 3: Floor drain blockage Floor drain is the final channel for washing machine drainage, if the floor drain is blocked, it will also cause backwater.

Solution: Clean the floor drain drainage channel.

Reason 4: The washing machine itself is a problem The drainage system inside the washing machine may also malfunction for various reasons after long-term use, resulting in backwater.

Solution: Need to find a professional for repair and replacement parts.

Finally, it should be noted that improper use of washing machines can easily cause backwater. For example, washing too much laundry or using too much spine agent can cause too much water to be discharged, which is more than the drainage system can handle, resulting in backwater. Therefore, when using the washing machine, it is necessary to comply with the corresponding usage specifications to avoid the occurrence of backwater.