Bathroom floor drain drain slow bath a place of water, what points to pay attention to when decorati

In addition to waterproofing, the most important part of the toilet is the drainage problem. But sometimes the floor drain of the new house we just installed is relatively slow to drain and every bath is water, what is the reason? After asking the host, I know that the problem of slow drainage is often due to less knowledge of interior decoration.

If you can pay attention to these three points, the drainage rate will be fast and the water will flow out.

Generally speaking, if you want to increase the drainage speed when renovating, you need to make an inclination on the ground and set the lowest value at the location of the floor drain. In this way, the water stored on the ground can be quickly discharged according to the normal condition of the water going down. However, sometimes due to the poor construction of some masters, it will also lead to slow discharge of stored water.

Therefore, in our engineering acceptance, we must do a good tilt test. Even if you don't need to add water to test, it's best to find a ping pong ball to test. Once you find that the slope drains slowly, or the ball does not fall naturally into the floor drain, it should be repaired in time.

Otherwise, it is very likely that there will be water from Jinshan Temple every day at home in the future.

1.Around the pavement method, the floor drain is embedded when laying the floor tiles. This eliminates the need to cut tiles to keep the house aesthetically pleasing, and drains relatively quickly.

2.Cross-paving method, this paving method is a floor drain 45 ° to put it in the core of the four tiles, it also drains faster, and it looks more beautiful and generous. 3.

Diagonal cutting, this kind of pavement is a more common way. It is to cut the floor tile diagonally into 4 parts, and place the floor drain in the core of the floor tile. All four floor tiles are slightly inclined towards the drain.

So this draining is fast.

In addition to the processing process affecting the speed of drainage, the quality and style of the floor drain will also affect the drainage of the room. Inferior floor drains not only have poor drainage, but also have weak aftertaste application. In addition, the following three floor drains seem to be best not used in showers.

1.The flap type is the most likely to cause blockage. Because there is a back cover on it, not only does it drain slowly, but it is also easy to accumulate stains.

2.The fatal disadvantage of not having a water-sealed floor drain is that it is easy to aftertaste and is not suitable for showers. 3.

Sealed in shallow water, it seems that the cup-type floor drain is easy to clog due to its shallow exhaust valve, and the internal water evaporates faster, which is very easy to recall.

This is the case in many families now. Some are not easy to cause blockage because of poor quality, and some are clogged because of long use time and accumulation of stains. So, in this case, we can use some gadgets to convey.

Or use some limescale cleaner on time to remove the stain on the pipe diameter, so that the problem of slow drainage can be solved.

The floor of the bathroom is leveled first. If you are going to replace the floor tiles in the bathroom, after chiseling the original floor tiles, be sure to level the floor with cement mortar before waterproofing. This avoids leakage of the waterproofing coating due to uneven thickness.

Bathroom floor drain waterproof practice: the joints should be painted in place. The joints between the walls and floors of the bathroom and the joints between the water and water pipes and the floor are the most problematic areas.

In the construction, you must urge the workers to deal with these corners and corners, and all waterproof coatings must be applied "in place". Wall treatment is also important. In the general bathroom waterproofing treatment, the wall should also be made about 30 cm high waterproof paint to prevent water from penetrating the wall.

However, if the wall of the bathroom is a non-load-bearing light wall, the entire wall should be coated with waterproof paint. If you have a two-fan shower screen in your home, the two walls that are connected to each other should also be fully painted. If you use a bathtub in your home, the wall adjacent to the bathtub should also have a higher height of the waterproof paint than the top edge of the bathtub.

The waterproof experiment must be done.

When decorating, you need to pay attention to waterproofing, pay attention to the problem of anti-slip, and be sure to pay attention to the specific height of the laying of floor tiles.

When decorating, we must do a good job of drainage, waterproofing, otherwise there will be great hidden dangers when using.

In home life, we often encounter such a problem, the floor drain is obviously not blocked, but the water is very slow, what is the reason for this? At this time, in addition to considering the problem of ground slope, we can also remove the floor drain cover, pour water into it to see if it is fast, if it is fast, it proves that the sewer pipe is not blocked, it is the cause of the floor drain, if it is still very slow, it is the sewer blocked, find someone to pass it.

There are two reasons for floor drain, the deodorant floor drain is slower than the ordinary floor drain, if you were originally decorated and installed with an anti-odor floor drain, or replaced with an anti-odor floor drain halfway, there is no problem, slow draining is also a normal phenomenon.

This is related to the odor-proof floor drain design, there is an additional water valve gasket at the bottom of the odor-proof floor drain, usually it is in a closed state, and it will only be opened when draining, so the water is relatively slow.

If it is the case of water pipe blockage, find a thin wire in front of the hook, turn back and forth in the floor drain, you can pull the blockage out, as for the greasy sediment blockage, it is generally rare but also the most difficult to deal with, it is recommended to find a professional clean-up personnel to help deal with it.

There is also a problem with the floor drain that has just been cleaned up for a long time? This is due to the fact that the corners of the pipes have a large amount of dirt that can quickly accumulate due to the entry of new garbage. It is recommended to install a filter screen in the floor drain to isolate debris and impurities.

1. The floor drain is blocked. One of the very important reasons why the toilet floor drain is very slow is caused by domestic garbage. In the process of daily washing, it is inevitable that some hair or fine garbage will flow into the floor drain, which will cause the floor drain to drain slowly over time, and even cause blockage, backwater and other phenomena.

2. Residue of construction waste. In addition, it is also possible that construction waste causes the floor drain to drain slowly, which is also a relatively common phenomenon at present, and usually occurs within half a year of occupancy. Of course, if you find this situation not long after moving in, then it can be sure that it is caused by construction waste.

3. The water pipe is offset. In addition to the above two reasons, in the process of home improvement, it is inevitable that there will be a certain deviation of the sewer pipe. For example:

The diameter of the floor drain is not perpendicular to the diameter of the sewer pipe, and even crooked or offset, so when we use the sewer pipe, it will block about half of the position, so that the floor drain is slow to drain.

Find a bucket that you don't use, fill it with water, remove the drain parts, wash them, and put them back in. It can usually be solved.

If that doesn't work, find a sewer master to come and take care of the sewer.

The floor drain is hooked with iron wire to remove the filter element inside, most of the reason is that the hair is clogged, just clean it up.

Find a sewer master to clean it up.

Bathing is an indispensable part of daily life, however, sometimes we may encounter a situation where the floor drain in the bath is very slow to lift the water. Not only does this make us feel uncomfortable, but it also adds to the hassle of cleaning. In response to this situation, we can take the following measures:

1.Clean the floor drain.

First of all, we can try to clean the floor drain. There may be some hair, dander and other debris stuck in the floor drain, causing the water to go slower. They can be removed using tools such as hooks, and the floor drain can be cleaned with detergent.

2.Use chemical cleaners.

If cleaning the floor drain doesn't work, we can try using some chemical cleaners. There are many kinds of cleaners available in the market, and you can choose to try them out depending on the situation. However, it is important to be safe when using chemical cleaners, keep it ventilated, and avoid contact with** and eyes.

At the same time, it should be operated in accordance with the instructions for use, and should not be overused.

3.Use a household cleaner.

If you don't want to use a chemical cleaner, you can try using some household cleaners. For example, we can use baking soda with white vinegar to make a cleaner to clean the drain. You can also use baking soda with warm water to make a paste, pour it down the drain, pour some white vinegar, and finally rinse it with hot water.

This removes bacteria and undesirable odors from the pipes without causing damage to the pipes.

4.Seek professional help.

If you've tried all of the above and still don't solve the problem, or you're not comfortable using chemicals such as detergents, then the best way to take a ride is to seek professional help. Ask a professional plumber or drainer to solve the problem. They can use professional tools and equipment to clean the drains quickly and overall with better and safer results.

In short, when you encounter a slow drain in the bathroom, you can try to use the above methods, hoping to solve your problem.

Floor drain is an indispensable hardware product in the decoration process of modern bathroom space, which can make the water on the floor of the bathroom space drain out immediately and keep the entire bathroom space dry, but if the bathroom floor drain drainage is slow, it will affect the normal use of the user. What should I do if the floor drain in the bathroom is slow? Let me take a look.

In fact, whether the floor drain drainage is smooth or not is mainly determined by the slope of the bathroom floor and the installation effect of the floor drain itself. To solve this problem, you can focus on the following 3 points:

1. The greater the slope of the bathroom floor towards the floor drain, the smoother the drainage. Generally, the slope of the lower drainage pipe should be more than 1%, that is, the slope of the 1-meter water pipe should be more than 1 cm, and the slope of the 3-meter water pipe should be more than 3 cm. Because the bathroom drainage pipe is relatively concentrated, and the drainage during the shower is a large area, the water can flow around, if the slope is not enough, it is easy to store water or slow drainage in some places with a relatively small slope.

Therefore, the slope of the bathroom floor must be appropriate, not too big or too small, if the slope is too large, people will feel uncomfortable standing on it. 2. There is another way to solve the slope of the ground, which can be done in the place of the bathroom cabinet or toilet, which is in case of water accumulation in the bathroom, so that the water can be drained through the floor drain in these two places. The slope of these two places can be slightly gentler, close to level, and the water can flow through it with just a little slope.

But in the shower, the slope should be moderately increased. 3. There is an effective way to solve the drainage slope, which is to increase the slope around the floor drain, install the bricks of the floor drain diagonally, and put the floor drain in the middle of the brick, so that the slope of the floor drain is very obvious. However, before installation, the owner should dock with the master and tell the master the size and specifications of the bathroom floor tiles, so that the master can install the floor drain.

Summary: The relevant information about the slow drain of the bathroom or what to do with the socks is introduced here, I hope this article will be helpful to you. If you still don't understand something, you can leave me a message below, and we will answer it for you as soon as possible.