1 hot water and one cold water in the wash basin, a faucet in the middle, how to fix the faucet leak

Most of the leaking faucets in the wash basin are caused by the aging of the leather ring, as long as the leather ring is replaced, it is no problem.

Step 1,Close all inlet valves

Close all the inlet valves for cold and hot water, otherwise you won't be able to work.

Step 2,Remove the handle

There is a screw on the upper part of the handle, and some of them are covered with logos, and you can see them when you warp them up.

Step 3,Dismantle the spool

Use an adjustable wrench to remove the spool counterclockwise.

Step 4,Replace the leather loop

The position pointed by the arrow is where the two leather rings are, and if you don't know which one is aging, just replace them all.

Step 5,Install the spool and handle back in reverse

How to disassemble and how to install it back to see if there is still leakage. If there is no leakage, it ends here, and if it still leaks, then move on to the next step.

Step 6,Remove the pad of the spool and replace it with a new one

This is the stepping stone, and if this thing is worn out for too long, there is a possibility of water leakage.

Step 7,Install it back again

It's definitely not leaking this time, unless there is a crack in the body of your faucet.

Well, that's the end here, ** leakage we can only rely on speculation, remove it to see, and we have to test it repeatedly, as long as there is a cone and a wrench at home, it's quite easy.

Water leakage will occur when the faucet spool is aging, so you can consider replacing the faucet or faucet spool. (Spool general element).

Ways to replace the faucet spool:

Turn off the water source and pry the lid of the faucet open with a screwdriver.

Then you will see the screws to remove the faucet, after removing the screws, remove the faucet spool.

Finally, replace the faucet spool with a new one, and install the faucet properly.

Please click Enter a description.

A hot water and a cold water in the washbasin, a faucet in the middle, if the faucet is leaking, if the faucet is leaking, it is very likely that the faucet is faulty, replace it with a new faucet, replace it and try it. If it is a sealing problem, it is recommended to replace the gasket in the middle and then try to replace it again.

First of all, open the cabinet under the sink, find the pipe under the faucet, there is a screw cap between the pipe and the faucet, after the screw cap is unscrewed, the faucet can be pulled up.

Then use an adjustable wrench to remove the main part of the faucet. When disassembling, you must be careful not to scratch the corners of the washbasin, because it is all ceramic and easy to be damaged, and you can use a towel to protect the basin next to the faucet before operating.

After treatment, the faucet should be installed on the washbasin according to the original method, and the faucet should be coated with waterproof glue near it to prevent water leakage in the future.

How to repair a leaky faucet in a wash basin

1. To turn off the water valve to open the cabinet under the basin, and then there is an interface where the faucet is in contact with the basin, unscrew the plastic bolts, and the faucet above can be removed.

2. Remove the faucet with a movable wrench, and then wrap a few loops of waterproof tape around the thread.

3. Connect the faucet to the water pipe, open the water valve, and then turn on the faucet switch to see if there is any water leakage.

4. If it is the reason for the water pipe, then it is necessary to replace this section of the water pipe, which requires a professional plumber to repair it, and there is no way to deal with this situation with ordinary leakage repair tape.

Pro, the solution to the leakage under the faucet basin of the wash basin 1, if it is the leakage of the water outlet of the basin faucet, then it is generally caused by the damage to the shaft gasket inside the faucet, then you need to choose a suitable size pliers according to the actual size of the faucet to remove the cover of the faucet, and then use the clamp to take out the shaft gasket that has been damaged inside, and then install the new axial gasket into it. 2. If there is a leakage phenomenon in the interface position of the basin faucet, then it is generally caused by the loosening of the nut at the interface position, so as long as the nut at the interface position is tightened, or a new U-shaped gasket can be replaced. 3. If there is a leak in the gap of the lower part of the basin faucet, then it is generally caused by the damage of the triangular gasket in the faucet gland, then you need to use a tool to loosen the screw, and then remove the faucet tether, and then loosen the faucet gland, and then take it off, and then take out the triangle gasket that has been damaged in the faucet gland, and then install a new triangular gasket into it.

If my answer is helpful, please give it a thumbs up (rate it in the bottom left corner) <>

I look forward to your praise, your efforts are very important to me, and your support is also the driving force for my progress<><

If you are satisfied with my answer, <>

You can click on my avatar for one-on-one consultation. Finally, I wish you good health and a good mood! <>

There may be several reasons why the cold water from the sink faucet does not come out of the water:1Scaling or plugging inside the faucet:

After prolonged use, limescale or debris may accumulate inside the faucet, resulting in poor water flow or complete blockage. 2.Clogged cold water pipes:

Cold water pipes can become clogged with debris or limescale, causing the water to flow poorly or stop completely. 3.Cold water valve closed or damaged:

If the cold water valve is closed or damaged, the cold water cannot be allowed to flow out. 4.Leaking cold water pipes:

If the cold water pipe is leaking, it can cause the water pressure to be insufficient or stop completely. 5.Cold water pipes are frozen:

During the cold winter months, cold water pipes can freeze, causing the water to flow poorly or stop completely. Workaround:1

Clean the inside of the faucet: You can use vinegar or a professional faucet cleaner to clean the inside of the faucet. 2.

Clean cold water pipes: Use a professional pipe cleaner or disassemble the pipes. 3.

Check the cold water valve: Check if the cold water valve is closed or damaged, and if it is damaged, it needs to be replaced. 4.

Check the cold water pipes for leaks: if there is a leak, it needs to be repaired in time. 5.

Solve the problem of cold water pipes being frozen: you can use hair dryers or hot towels to thaw them.

The cold water from the wash basin faucet may not be due to a problem with the faucet itself. There are several possible reasons why stoves are sold as follows:1

There is limescale or sediment inside the faucet or water pipe that is blocking the water flow. This may be due to the high amount of calcium and magnesium ions in tap water. 2.

There is a problem with low water pressure in the faucet or pipe. 3.The faucet has a problem with damage or leakage.

It is recommended that you try to clean the faucet or water pipes of scale or sediment, check if the water pressure is too low, and check the faucet for damage or leaks. If none of these methods can solve the problem, it is recommended that you have a professional to inspect and repair the strap.

What is the reason why the sink faucet in the bathroom at home does not come out of water?

Dear, I'm glad to answer for you: What is the reason why the faucet of the washbasin in the bathroom at home does not come out of water? A: Hello, dear! <>

The reasons and solutions for the lack of water in the faucet of the bathroom sink are as follows: 1. Unscrew the faucet outlet to check and clean it. On the mount to see if the water is restored.

2. Check the hose connection of the faucet, some faucets have installed a filter screen in order to prevent entering the sand, which is blocked due to the interception of a lot of debris. 3. Knock the filter in the water a few times, and the sand and other debris will naturally fall down and rinse it and install it as it is. 4. Note, it's best not to pick it with your hands, which will press the sand into the filter and get stuck, and don't wash the rubber mat away!

Thank you for your patience. If my answer is helpful to you, please also give a thumbs up (comment in the lower left corner Oh ambush), look forward to your like, your efforts are very important to me, and your support is also the dynamic respect for my progress. If you feel that my answer is still satisfactory, you can click on my avatar for one-on-one consultation.

Finally, I wish you good health and a happy mood!

The steps to repair a washbasin faucet leak are: closing the inlet valve, removing the handle, removing the screws that hold the gasket in place, replacing the old gasket with the same new gasket, and installing the faucet components.

Close the inlet valve

First of all, remove the small screw on the faucet handle, you can remove the handle that is fixed to the faucet body. Some screws are hidden underneath metal buttons, plastic buttons, or plastic pieces that snap into or screw into the handle. As soon as you turn the button on, you will see the handle screws mounted on the top.

If necessary, some penetrating lube can be used to loosen the screws.

Remove the handle

Then use large pliers or an adjustable wrench to remove the filler nut, being careful not to scratch the metal. Rotate the spool or shaft in the same direction as when the faucet is turned on so that they can be unscrewed.

Remove the screws that hold the washer in place

In this step, remove the screws that hold the washer in place and check that if necessary, you can use penetrating lubricating oil to loosen the screws. Check the screws and spool, if there is damage it is necessary to replace it with a new one.

Replace the old gasket with the same new one

Replace the old gasket with the same new washer, also note whether the old washer has a bevel or flat, and replace it with the same new washer. Gaskets designed for cold water only expand violently when hot water flows through them, clogging the outlet and slowing down the flow of hot water. Some gaskets work in both hot and cold water.

Install the faucet parts

You'll need to attach the new gasket to the spool and reassemble the parts in the faucet. Rotate the spool in a clockwise direction. Once the spool is in place, reattach the fill nut. The caution here is not to let the wrench leave scratches on the metal.

Summary. Hot water and cold water are piped by two water valves, and the hot water leakage should be due to the hot water valve being loose.

The faucet on the washbasin, the hot water leaks, the cold water does not leak, what is the matter?

Hello, I have seen your question and am sorting out the answer, please wait a while Hot water and cold water are piped by two water valves, and the hot water leakage should be the hot water valve is loose.

Try adding two rubber gaskets.

Supplement: 1. You can try to change the valve core by yourself. The lid on the handle can be pried open with a blade along the gap. There is a screw inside when opened, loosen it with a screwdriver, and the handle can be pulled upwards.

You can see a nut, remove it with a wrench, you can take out the valve core, go to the plumbing parts store and buy a touch and put it back. The valve core is divided into two kinds of hot and cold water, red hot water and blue cold water, do not install the wrong side.

2. Clean the connection between the switch and the washbasin, tighten the fastening screws, and then squeeze the glass glue on the connection, and use it when it is dry until it is not sticky.

The characteristics of glass glue are that it has a strong seal, even if it is dry, it is soft, and when it needs to be repaired in the future, it can be gently cut with a utility knife.