I have just installed the faucet at home, but what should I do if I find that it is not in a hurry?

When the nut is not screwed by hand.

, fix the nut with your right hand, and rotate the main body of the faucet with your left hand to the right side 90 degrees, so that the faucet can be fixed steadily, and the direction of the faucet operating handle is also normal. Tighten this bolt buckle under the faucet and you're good to go. If it can't be operated, take the basin off, tighten it and fix it again.

Tool required: hex wrench.

Wrenches, pliers.

Dishcloth. 1. Turn the faucet 45 degrees to facilitate the use of hex wrench. 2. Insert the hex wrench into the hole behind the faucet and rotate clockwise.

Add a cushion (stool, ladder, etc.) that can touch the faucet and tighten the faucet. The faucet is fixed on the water pipe, and if it is screwed to the end, it can only have one or several fixed angles. As for why you twist it up, I think it may be that the threads of the two do not match, you can loosen half a circle to try, if there is a leak, wrap more tape.

Wrap raw material tape. The method is to put the faucet interface facing you, and then wrap it in a clockwise direction, so that the direction of the screwing interface and the direction of the winding strip are the same. After many tests, the raw meal belt is wound about 10 times, which is more suitable, and it can be wrapped more or less according to the actual situation.

If you have strong hands-on ability, you can do it yourself, the first step is to judge whether your faucet is single or double water (hot and cold water), to buy the corresponding valve core. At the same time, the water valve is repeatedly opened, fully closed, opened, and fully closed, and a small amount of impurities in the faucet flow out with the water, and the total valve will return to normal. If this does not solve the problem, the simple solution is to change the valve.

Ceramic spool or copper spool leakage, in this case, just change a spool, when installing, you need a wrench, a slotted or Phillips screwdriver.

It's almost done. Generally, the faucet valve core is seriously damaged, or the faucet is not closed tightly due to the poor quality of the valve core, and the phenomenon of dripping water occurs. In most cases, you can only replace the entire faucet, and replacing the valve core is not something that ordinary people can complete, and the matching valve core is not easy to buy.

Don't worry if you find it, try the water first to see if the faucet has water seepage, if there is water seepage, close the sluice, and then tighten the faucet with a wrench.

If the faucet installed at home is found to be not tight, then you can use a wrench to screw a few more times, if it is still not tight, it means that the size is not suitable and you need to buy it again.

If the faucet is not tight after installation, you can use a wrench to turn a few more times, if it is still not tight, it may be that the water pipe and the faucet are not matched.

If the faucet is broken, it is recommended that you go and get a new one.

Summary. Wrap a little more, it will occupy the thread position, so as to screw to the best position.

How to solve the problem of improper installation of faucets?

Hello, dear, I'm glad that your question is bothering you to tell me what the specific problem you have encountered, and I will analyze and answer it for you.

The faucet is broken, and when you install it after removing it, you can't install it properly?

Under normal circumstances, the faucet installation error needs to be removed, re-install whether it is an installation error or a material use error, it needs to be changed correctly, I hope mine is helpful to you, if you have any questions, please continue to ask, thank you.

Wrap the raw tape and then install it, and it can be adjusted to the correct position, which is also the tightest position to be screwed.

How do I get the raw tape I use? Even if I adjusted several angles, it was not correct.

Wrap a little more, it will occupy the thread position, so as to screw to the best position.

It is not necessary to tighten it to the tightest, it is generally tight.

Summary. The pros are as follows; Increase or decrease the raw material belt that wraps around the outer wire of the faucet. Under normal circumstances, a good raw belt only needs 15 to 17 turns to wrap the outer wire of the faucet, while a poor raw belt is likely to need 30 to 35 turns; Observe how far the faucet outlet is from the downward righting?

Before wrapping the raw material belt, determine the number of rings in the inner wire mouth of the faucet rotation. Before wrapping the raw material belt around the outer wire mouth of the faucet, screw the faucet into the inner wire elbow, then count, turn the faucet a few times to the bottom, and then wrap the outer wire mouth with the raw material tape, rotate the number of turns just now with the elbow of the inner wire mouth, and use the sealing silicone gasket (gasket).

What should I do if I find that the water outlet is facing the wrong direction after the newly installed faucet is tightened?

The pros are as follows; Lift the reed to increase or decrease the raw material belt that wraps around the outer wire of the faucet. Under normal circumstances, a good raw material belt only needs 15 to 17 turns to wrap the outer wire of the water shono belt faucet, while a poor raw material belt is likely to need 30 to 35 circles; Observe how far the faucet outlet is from the downward righting? Before wrapping the raw material belt, determine the number of rings in the inner wire mouth of the faucet rotation.

Before wrapping the raw material belt around the outer wire mouth of the faucet, first screw the faucet into the inner wire elbow, then count, turn the faucet a few times to the bottom, and then wrap the outer wire mouth with the raw material tape, and rotate the number of turns of the ridge leakage just now with the elbow of the inner wire mouth, and use the sealing silicone gasket (gasket).

The solution to the faucet with the mouth facing up is that when the dusty jujube head faucet has been unscrewed and the water outlet is still facing up, how to solve it at this time is the most important thing to know. The best way to untie the envy: reinstall.

For the faucet has appeared to be unscrewed, and the outlet is still facing up, the solution at this time is to reinstall, other methods are a joke, anyway, it is not their own home, and when it is their own home, it will be said that it must be reinstalled to be guaranteed. Standard steps for reinstallation:

Disassemble the faucet: disassemble the faucet that has not been screwed in the opposite direction; ②.Clean up the raw material belt:

Disassemble the faucet and clean up all the original raw meal belts; ③.On the new material belt: for the raw material of the faucet, if it is winding, it is very problematic.

First of all, according to the installation of the head dragon, the raw material belt direction is wound 25-32 times in the faucet, and then use your fingers to press the raw material belt along the outer silk pattern at the most water inlet position of the faucet, and at the same time ensure that the end of the raw material belt is also pressed out; ④.Installation: Wait for the tap that has been wound around the raw material tape and start the installation according to the direction of the screws.

When installing, you can first twist it by hand 3 times, and at this time it will already be difficult to twist; ⑤.Correct the direction: with the help of external tools, continue to twist the faucet for 1-2 turns, pay attention to the first turn, if you feel that the strength is already very large, then do not continue to screw after the direction of the head is corrected, at this time the faucet has been scattered to do not leak; ⑥.

Inspection: After the installation of the head is completed, open the tap water valve to let it pass the water, at this time the installation of the faucet is inspected to see if there is any water leakage, if there is no leakage, the installation is qualified, if there is a water leakage, use the tool to continue to tighten a circle, so that the faucet slag is installed completely.

There are several possible reasons why a faucet is not properly installed:

1.Improper alignment during installation: The faucet needs to be installed on the water pipe, and if the water pipe and faucet are not properly aligned during installation, it can lead to improper installation of the faucet.

2.Mismatched sizes of pipes and faucets: Water pipes and different types of faucets have different sizes, which can also lead to improper faucet installation if different sizes of pipes and faucets are mixed.

3.Improper tools used during installation: When installing a faucet, it is necessary to use the right tools. If the tools used are not right, it may result in improper installation of the faucet.

4.Problems with the faucets themselves: Some faucets have problems with their own, such as poor quality or production problems, which can lead to improper installation.

5.Improper installation position: If the faucet is installed in the wrong position, it can also lead to improper installation of the faucet.

Summary: Improper faucet installation can be caused by a variety of reasons. The best way to solve this problem is to use the right tools to ensure that the pipes and faucets match, are properly aligned, and are installed in the right places.

The faucet is an important fitting to connect the water pipes, with which the tap water can be turned on and off at any time. Usually the faucet will be damaged after a few years of use and need to be replaced with a new one. Installing a faucet may seem simple, but if you don't pay attention to it, it will not be installed properly.

Why the faucet is not installed properly.

It may be that the position is not aligned when screwing, and you need to find a good direction when you start screwing, and make sure that it is still facing the original direction after tightening, so that there will be no improper installation. You can also check whether the connection thread between the faucet and the pipe is damaged, if the thread is intact, there will be improper installation, then you can wrap some raw material tape on the external thread to adjust the orientation.

What are the precautions for the use of faucets.

1. You can't use force when opening, generally just gently rotate or toggle. When it is closed, it can not be screwed to death, so it is easy to damage the internal accessories of the faucet, and you only need to ensure that there is no leakage. Faucets with screen covers at the outlets need to be cleaned of impurities frequently and removed for rinsing at regular intervals.

In the case of a hose faucet, it should be kept in a natural stretch at all times, so that it is not easy to break.

2. The faucet needs to be cleaned frequently, and the sponge can be dipped in toothpaste to wipe it when cleaning to ensure that it is as clean as new. Note that the surface of the faucet should not be brushed with steel wool balls or other hard objects, which is easy to scratch the surface and affect the aesthetics. In addition, you should not use aggressive detergents when cleaning to avoid corroding the surface of the faucet.

After washing, you should dry the water with a dry towel or rag to prevent limescale from forming.

Article summary: The above is to introduce to you why the faucet is not installed properly and what are the precautions for the use of the faucet, I hope it can help some friends in need.