Gas water heater filter cleaning? How to clean the water heater filter

Gas water heaters.

The dirtiest part of the filter may be cleaned regularly, which can be wiped with a rag or, if not, gently brushed with a small brush. In addition, since the water heater works in the kitchen for a long time, cleaning with detergent is also a good solution.

The specific steps are as follows:

1. Turn off the faucet first, then turn off the power of the water heater, and then pull out the power plug. Note that this process should keep your hands dry and not wet with water.

2. Then remove the inlet pipe of the water heater, and then find the filter screen to be cleaned in the filter valve. Be careful to gently use a tool you can find, such as household tweezers.

or small clips) to take out, preferably not directly by hand, to avoid contamination and damage to the filter.

3. Gently put the removed filter screen in the pool, use a small toothbrush to gently remove all the foreign dirt, and then wipe it with a clean rag and wait for it to dry. If the appearance of the filter is not very dirty, you can also clean it directly with a rag, install it back inside the water heater after the filter is dry enough, and turn on the water inlet valve and power supply to use it normally.

Filter Cleaning Method:1.Separate the upper and lower sections of the filter and use a clean, unbrushed new toothbrush to brush the surface of the filter while rinsing the upper filter (ceramic) with clean tap water.

2.When the upper filter element is filled with about half a pot of tap water, shake the filter element up and down several times, pour out the remaining water, and reciprocate several times to make the micropores of the filter element unblocked, fill the lower filter element with tap water, and pat the mouth flat up and down with the palm of your hand to make the lower filter element shake, and make the tap water clean the filter material. This is repeated several times until the tap water coming out of the lower filter is clear.

3.It is to clean the diet and heat the cooling chamber, put clean water, and then repeat the rinse several times without any problem.

1. Unplug the power plug. 2. Unscrew the end of the water inlet pipe connected to the water heater, and gently remove the filter screen in the filter valve with tweezers or needle-nose pliers. 3. Put the removed filter into the running water, use a toothbrush to clean up the rust or iron filings and other debris on the filter screen, and then install it back in the reverse order of disassembly, until it can be used normally after confirmation.

When dismantling, you must pay attention to turn off all the faucets of the inlet valve, turn off all the switches, and then unplug the power cord to ensure that it is operated in an environment without electricity.

Precautions for disassembly:

1. Unscrew the side of the water heater connected to the water pipe when disassembling, and then take out the filter screen with tweezers or clips.

2. After taking it out, it must be cleaned, and it can be cleaned with some soft brushes in the pool or after opening the faucet, and the accumulated dust or rust must be cleaned up, and then reinstalled in accordance with the above way and then tighten the screws connected to the water inlet.

3. When cleaning, you must pay attention to using cold water to clean, because hot water is easy to burn the filter.

4. It must be noted that after using it for a period of time, it is necessary to clean the filter screen frequently, or replace the filter screen frequently, otherwise the long use time will also cause the dust accumulation and blockage of the water pipe, which will lead to a great reduction in the service life of the water heater.

1. Turn off the faucet before removing the filter, and then turn off the power supply and pull out the plug of the power supply. During this process, take care to keep your hands dry and do not come into contact with water. 2. Slowly unscrew the end of the inlet pipe connected to the water heater, then find the filter screen to be cleaned in the filter valve, and gently take out the filter screen in the filter valve with small household tweezers or small pliers with a sharp nose, it is best not to use your hands directly, so as not to pollute and damage the filter screen.

Reason: 1. When the water pressure is stable, please check whether the water outlet of the water heater is normal.

2. If the water heater outlet is abnormal, you can consider whether the filter screen of the inlet valve is blocked by foreign bodies, and when there are indeed foreign bodies, we need to disassemble and clean the filter screen of the water heater. After the filter is dry, it can be installed back inside the water heater, and after confirmation, you can open the water inlet valve and power supply water inlet for normal use.

3. Gently put the removed filter into the running water, use a small toothbrush to gently remove foreign objects and dirt such as rust or iron filings on the filter screen, and then wipe it with a clean rag and wait for it to dry. If the appearance of the filter is not very dirty, it can also be cleaned directly with a rag.

The first thing you should do is turn off the faucets and power to ensure that the cleaning is done safely. There is a connection between the water inlet and the thermostat. When you remove it, you can see that there is a sieve inside the filter valve, which contains a large amount of scale and impurities.

At this point, you need to gently move the screen away with tweezers. Then put the filter under the faucet to clean the wax, and install it back after cleaning.

Other knowledge popularization:

1、?There is a lot of dirt on the filter screen, which is difficult to clean. You can use a toothbrush or a small brush to carefully remove the dust from it. Then install the filter correctly and check if the filter is working properly. The filter must be properly installed in order to function properly.

2. For the filter screen of the gas water heater, it should be removed and cleaned frequently. In fact, the cleaning process is very simple. You just need to be careful not to damage other parts, and you also need to pay attention to cutting off the power supply in time.

If you find that the cleaning effect of the filter is not good, you can contact the after-sales service department, and professionals will come to clean it.

3. The cleaning of the filter screen cannot be ignored, because once the impurities block the forest hole and slip the filter screen, the water production of the water heater will be reduced, and even the water heater will not be seriously activated. You need to find the correct position, carefully remove the strainer and wash it several times. If you don't know how to operate at home, you can ask a professional maintenance master to come to operate.