How to clean the double layer filter for stir frying?

1. The reason why it is difficult to clean the filter screen of the range hood:

1.The filter screen is the first step of oil smoke filtration, which is in direct contact with oil smoke and has the largest contact area with oil smoke.

2.The structure of the filter screen is dense and uneven, and it is difficult to clean.

Here's how to clean the headache filter?

Is the range hood filter difficult to clean? Three tips to do it all!

Second, cleaning tips:

1.Homemade cleaner.

1) Prepare a watering can, prepare 60-80 hot water, mix vinegar and dish soap in a ratio of 6:1, then pour to 1 3 of the watering can, and then pour the watering can full of hot water.

2) Spray the prepared solution on the filter screen to make it fully react and fuse, and soften and dissolve the oil.

3) Leave it for 10-15 minutes, wipe off the oil stain on the filter screen with a scouring pad, the thick oil stain is easily cleaned off, if there is a thick oil stain, you can spray it many times until the oil stain is removed.

2.Alkaline surface cleaning method.

1) Clean the oily surface of the range hood with warm water at 50-60 degrees.

2) Sprinkle alkaline flour powder on the scouring pad and wipe directly on the oil.

3) The alkaline surface absorbs water and dissipates heat, and try to wear rubber gloves when scrubbing.

4) Soon the oil stain dissolves and is easily wiped off.

3.Waste oil removal method.

1) Dip a little kitchen oil on a paper towel.

2) Apply evenly on the kitchen filter and apply a paper towel to the surface of the hood.

3) After standing for 1 hour, the oil will soften and dissolve, which is based on the principle of dissolution of the same substance.

4) Wipe the oil stain with waste paper or waste cloth first.

5) Then wash carefully with detergent and scouring pad, and rinse with water.

Precautions for the use of range hoods:

1) The range hood cannot be burned with charcoal and other fuels in the same flue to prevent disasters.

2) The kitchen using the range hood should be well ventilated.

3) It is forbidden to smoke directly from the stove.

How to clean the double-layer filter for stir-frying? Range hood is an indispensable household appliance in the kitchen, usually using a range hood for stir-frying, the air becomes very good, and it is also beneficial to our health. Due to the large amount of cooking fumes, the filter of the range hood used for a long time is full of oil smoke, and it will become very dirty if it is not cleaned.

Due to the variety of materials of range hood filters, the cleaning methods of different materials are also different. For example, the thin filter of the screen window cannot be cleaned. There is also a stainless steel mesh, which is easier to clean, and can be washed directly in the basin, and it is good to wash it with a brush.

There is also an iron mesh, which is cleaned in the same way as the stainless steel oil mesh.

Eight-colored birds.

Soak in hot alkaline water for 10 minutes, and then gently scrub with an iron brush to clean it.

If the stain on it cannot be cleaned, it can be put on the fire and then cleaned.

1. Prepare a basin of hot water, pour in baking soda and let it melt completely.

2. After the baking soda powder is dissolved, put it in the strainer and soak for 10-20 minutes (the water should cover the strainer).

3. Use an old toothbrush to brush the soaked filter directly.

4. With a few brushes, you can easily remove the grease on the filter screen.

Wash with alkaline surface and clean the oily surface of the range hood with warm water at 50-60 degrees. Sprinkle alkaline powder on a scouring pad and wipe directly on the oil. The alkaline surface absorbs water and dissipates heat, and try to wear rubber gloves when scrubbing. Soon the oil dissolves and is easily wiped off.

Range hoods are widely used in our lives. There are several devices on the range hood that can help to smoke the hood. Strainer. Due to the large amount of cooking fumes, the filter screen of the range hood used for a long time is all fumes, if not cleaned.

Pressure cooker steam flushing method. Boil the cold water in the pressure cooker, remove the pressure limiting valve when the steam is continuously discharged, open the range hood, and align the steam water column with the rotating fan blades, because the high hot water steam continues to rush into the fan blades and other components, the oil and sewage will flow into the waste oil cup along the road until there is no oil in the oil cup.

Prepare a basin of hot water, pour in baking soda, after the baking soda is dissolved, put it in a strainer and soak for 10-20 minutes.

Use an old toothbrush to brush the soaked filter directly.

With a few brushes, you can easily remove grease from the filter.

You can prepare a watering can, then collect hot water at 60 to 80 degrees, mix ginger vinegar and dish soap according to one to one, pour one-third of the watering can and spray it on the strainer to make it fully reflect, soften and dissolve the oil.

If the double-layer strainer for stir-frying is sticky, it is recommended to put it in a pot of boiling water and steam for a while, then rinse it with a brush and dish soap, rinse it several times, and it will definitely be rinsed clean.

Boil water in a pot on the stove without covering the lid, and the water vapor will naturally drift on the range hood after the water is boiled, which plays a role in dissolving oil stains. Soften the grease with hot air.

1. Put the filter into the basin, put water in the basin, soak it with water first, wait for a period of time to soak softly, and then brush it several times with a toothbrush.

Brush it with a brush. Then rinse with water. The effect is very good, and there are good other ways to clean the filter.

You can use a brush with longer hairs and rinse with water.

There are three materials for the range hood filter 1 is similar to a thin filter screen for a window screen, this filter can not be cleaned, it is simple to replace directly or can not be used, 2 stainless steel mesh, this filter is relatively simple to clean is to put the filter into the basin, then pour hot water, add an appropriate amount of washing powder, and clean it with a brush, 3 The iron mesh of the Chinese range hood,

Put water in a ceramic or plastic basin, then add some caustic soda, and then soak the filter into it.

Caustic soda is very corrosive, so pay attention to corrosion protection and wear gloves yourself.

Spray it with a range hood to remove the oil and spray it, and it can be removed after a few minutes, and repeat again if there is a stubborn stain.

Take off the strainer and put bubbles in the oil agent.

Professional cleaning range hood bright moon cleaning.

If you return to the containment, how to disperse the cleaning of the range smoke Xiangshi's machine?

This kind of filter is OK to buy a new one at the hardware store and replace it.

The filter screen for oil smoke is very thin, grease, not easy to clean, and it is not expensive to buy a new one, 5 10 yuan a.

I take it off and wash it directly.

If you don't dismantle it, buy Mr. Vermeer kitchen heavy oil spray, spray it directly, the oil and detergent will flow down together, I often do this hygienic, convenient.

Put it on the fire and it'll be easy to clean up!

Wash with hot water and dish soap. It feels a little unclean in the nest where the vegetables are fought.

The range hood is a good helper in our life and is the kitchen.

The indispensable kitchenware, Fangtai.

Range hood is a relatively well-known brand in the range hood brand, which is used by more people, and it is also a range hood with better quality. However, after a long time, the range hood will inevitably need to be cleaned, and the filter is generally removed for cleaning, so how to remove the filter screen of the Fotile range hood? How to clean the range hood?

Now let me give you a detailed introduction to how to clean the range hood.

How to remove the filter of Fotile range hood

1.Wear gloves to prevent oil from sticking to your hands.

2.Hold the cartridge with your hand, then gently lift it upwards while rotating the cartridge clockwise. Rotate about 90 degrees to remove the oil box.

3.Remember, before moving the oil box, now spread a paper towel directly underneath it. Prevent oil from dripping out after removing the box.

4.The next step is to disassemble the filter, which is actually a grid of oil accumulation. After inspection, there is actually only one screw, which is concentrated on the middle point on the right. At this time, you can twist the screw out by gently turning it counterclockwise with a screwdriver.

5.After removing the screws of the grid, we need to gently push the grid to the right, and then we can find that there is actually a slot on the left side of the grid. Untie the slot to remove the grid.

6.After removing the grid, we found that this is actually a double-layer grid, and we need to clean it separately. Basically, all the parts that need to be cleaned are disassembled here. As long as these parts are cleaned, other parts only need to be wiped a little.

How to clean the hood

1.Use a professional belt sprinkler.

of degreasing cleaners.

Normal cleaning starts with detergent, it is recommended that you use the kind of degreasing cleaner with a professional nozzle, take a rag, spray a little and wipe a little, of course, this is only for range hoods.

On the surface, this method is not easy to use at all.

2.Soak in a mixture of vinegar and dish soap and rinse.

I have tried a lot of methods, and the more grease is to use a mixture of vinegar and dish soap, mainly after soaking the dish soap in water, put a small amount of vinegar after foaming, and then put the fan blades, strainer and oil storage box into the soak for 30 minutes before cleaning. Of course, the water soaked in the mixture can also wipe the grease on the surface.

3.Use a steel wool ball or wire brush to clean it, and you can use a card to scratch it gently.

For the grease on the fan blade and filter screen, you need to use a card to scrape off a part of the grease first, and then use a steel wool ball to brush, for the hole is blocked, you need to poke it open with a fine wire before continuing to clean. This part will probably take a lot of your energy. These can help you better clean the range hood and also introduce how to disassemble the Fotile range hood filter, which needs to be divided into six steps, these steps are in order, and the operation of each step needs to be careful to avoid damaging the Fotile range hood filter.

There are also some mentioned precautions, and consumers should pay more attention to them when operating.

1. How to disassemble the Fotile range hood.

To remove the oil tank, place your hands flat on the left and right bottoms of the oil tank and pull horizontally towards your body until the oil cup can be removed.

Disassemble the smoke board: put both hands on the smoke guide board along both sides, the fingers touch the plastic button first, and the fingers along the board should use the force of straight down pressure, press the buckle to remove the smoke board; Wrong hand pose: The fingers should not have the strength to bend towards the palm, and the fingers should be twisted inward.

Disassemble the oil net: unscrew the air inlet ring for four or six weeks with a Phillips screwdriver to remove the air inlet ring.

Second, how to clean the range hood of Fotile.

1.Take a plastic bottle (all kinds of beverage bottles that can be pinched flat by hand), poke more than 10 small holes in the lid with a sewing needle, and then fill it with an appropriate amount of cleaning detergent, and then fill it with warm water and shake it evenly.

2.Start the range hood and spray the cleaning liquid with a plastic bottle full of cleaning essence to the part to be washed, at this time, you can see that the oil and dirty water flow into the oil storage hopper together, and pour it when it is full.

3.After the cleaning solution in the bottle is used up, continue to prepare and repeat the cleaning. Until the dirty water flowing out becomes clear, depending on the degree of fouling, it can be rinsed after 3 times.

4.If the fan blade is equipped with a grille, it is advisable to remove the grille first to enhance the washing effect.

5.Use a rag to wipe around the intake port, the surface of the casing, and the lampshade.

Hope it helps! Pro-3

The range hood is the most direct contact with the range hood every time we stir-fry, and the range hood filter is often the dirtiest place of the range hood, so we often need to disassemble and clean, so how to remove the range hood filter? What are the precautions? It is relatively simple to remove the filter screen of the range hood to clean, but many people do not like to carry it out, so if it is not dismantled and cleaned, how to quickly remove the oil from the filter screen of the range hood?

Now let me tell you more about it.

How to remove the range hood filter

1.Remove the front bezel of the range hood to avoid bumping heads and obstructing the view.

2.Remove the oil cup. The oil cup contains waste oil, so take care of it.

3.Remove the filter bracket, loosen the fixing screws, and remove the bracket.

4.After washing the filter holder, prepare to replace the filter.

5.Replace the filter screen, spread out the filter screen, gently place it in the bracket, snap the filter screen under the bracket protrusion, tidy up the filter screen, flatten it, and put it right.

6.Replace the filter holder, oil cup, and baffle in turn. It's basically the same as the disassembly process.

Quickly remove oil from the range hood filter

Method 1:

1.Remove the oil cup, pour out the oil, and wash it with detergent.

2.Unscrew the gong wire with a gong wire knife, put it on the side and don't drop it, and use it when you can install it.

3.Remove the oil filter and grid, slowly separate it, and hold it with a newspaper so that the oil does not get on your hands.

4.Wrap the newspaper and take it to the open space outside.

5.If you burn it in an open area, the oil will burn automatically if you set the newspaper on fire.

6 .After the fire is extinguished, cool for a while, and then clean it with water, it may be a little black, which will not affect the use.

7.Pack it according to the order of disassembly and washing, and be sure to put the oil cup on, otherwise there will be oil everywhere. It is good to clean the surface of the range hood with a cloth and detergent.

Method 2:

1) Unscrew the screws that hold the grille in place.

2) Soak the removed filter cover in warm water with neutral detergent for 5-10 minutes.

3) Use a soft plastic brush to clean the dirt in the pores of the filter screen, and then wipe it dry with a dry rag.

4) Install the filter cover as before removal.

5) After installation, check whether the oil circuit of the appliance is smooth and whether the sealing ring on the volute can be sealed.

6) Please clean the filter screen cover according to the cycle specified in the manual.

Precautions: Be sure to burn it in an open space outside.

After burning, wait for it to cool down before holding it with your hands, and be careful of soup injuries.

Above, to give you an answer to the range hood filter how to disassemble, briefly introduced the removal steps of the filter, I hope to provide a useful reference for the disassembly and washing of the range hood filter, if you do not disassemble the range hood filter consumers also have a way to clean it, so in the second half of the article introduced two specific methods of range hood filter cleaning. Pay attention to use warm water when washing, so that the washing is more clean. Hope it helps.