Why does the mobile network set top box suddenly turn off after 20 minutes of watching TV?

Possible reasons why the set-top box will automatically shut down after powering on:

1. The standby function of the set-top box is turned on.

Standby off function method:

Turn on the set-top box and TV switches, and wait for the set-top box to start; After the set-top box starts, press the "Menu" button of the set-top box remote control; Enter the "Menu", then use the arrow keys of the remote control, find the "System Settings", and click the "Confirm" button of the remote control to enter; Find "Set-top box sleep" and change the option to "Off"; When you're done, press the "OK" button to save and exit.

2. The power adapter of the set-top box.

Abnormal. Solved: Replace the normal power adapter.

The set-top box is powered off. Exclude user power outlets.

Whether there is a fault, or whether the power plug of the set-top box is loose. How often does this happen, and whether it occurs after upgrading the system version.

Don't connect to the signal source,Let the box run alone,Observe the heat dissipation problem of the box,See if there will be an automatic shutdown,You can also judge whether it is a TV or software in turn。

Automatic shutdown may be a problem with the system, you can try to restore factory settings.

Eliminate all possibilities, only the box is faulty, parts are damaged, or the motherboard has problems, and the only way to do this is to find a technician to overhaul it.

After the TV is turned off, the set-top box will automatically turn off the signal after a few minutes, how can I prevent the set-top box from turning off automatically?

It is normal for the network TV set-top box to start again every time it is turned on, and it is enough to wait a few minutes. The reason why the signal is interrupted as soon as the newly installed TV set-top box is turned on is: 1. The feeder F head of the input feeder of the digital TV set-top box is not done well or is not screwed well; 2. There is a problem with the cable TV line, and there is no signal input.

It is necessary to report to the cable TV management department for repair; 3. The power outage and equipment maintenance of the Shansan cable TV room were temporarily interrupted.

Summary. The network TV set-top box stops on the boot page, what to do to stay on the boot interface Reason: Since the network set-top box has been on the intelligent system, the speed of upgrading is comparable to that of a mobile phone.

The speed of software update is faster, some set-top boxes may be single-core, dual-core, the system version is, and the hardware configuration and system version required by the program are relatively high, and various problems will occur. It is precisely because of these instabilities that various problems occur in the network set-top box. And getting stuck on the boot interface is the most common problem.

Solution: In fact, this kind of fault is very easy to solve, even if it is a novice, it can be solved by hand. We just have to do a factory reset.

Please strictly follow the following methods to restore factory settings: first, turn off the TV and unplug the power of the network set-top box; Then find the REST hole where a toothpick or paper clip is inserted into the set-top box; Then plug in the power supply, and when the TV sees the picture, release the REST button; At this time, the top box will be automatically started, we don't need to do anything, and when the network set-top box is restored to the factory, you can enter the interface smoothly.

What should I do if the IPTV set-top box stops on the boot page.

The network TV set-top box stops on the boot page, what to do to stay on the boot interface Reason: Since the network set-top box has been on the intelligent system, the speed of upgrading is comparable to that of a mobile phone. The speed of software update is faster, some set-top boxes may be single-core, dual-core, the system version is, and the hardware configuration and system version required by the program are relatively high, and various problems will occur.

It is precisely because of these instabilities that various problems occur in the network set-top box. And getting stuck on the boot interface is the most common problem. Workaround:

In fact, this kind of fault is very easy to solve, even if it is a novice, the fault can be solved with hands. We just have to do a factory reset. Please strictly follow the following methods for factory reset:

First of all, turn off the TV and unplug the power of the network set-top box; Then find the REST hole where a toothpick or paper clip is inserted into the set-top box; Then plug in the power supply, and when the TV sees the picture, release the REST button; At this time, the top box will be automatically started, we don't need to do anything, and when the network set-top box is restored to the factory, you can enter the interface smoothly.

Mine is the new Mobai box m301a,Can't enter the system,It's been booting the screen,What should I do?

Wait a minute, dear. I didn't find the reset key on the box, solve.

It's a system error. Enter RE mode and reset the factory settings. Turn off first, then press and hold the power button and the volume down button at the same time when the power is turned on, use the volume "up" and "down" keys to select the recovery row, and press the power button.

Then it's a factory reset. If it still doesn't work, contact the after-sales service.

Okay, I'll try. Uh-huh.