The wardrobe at home is very long, how to avoid deformation later?

Some friends in the whole wardrobe in the process of use, the wardrobe is easier to deform, the wardrobe is the need for us to treat gently, careful maintenance, today the prince will support a few tricks for everyone, we should pay more attention to the following points in the use of the wardrobe in the future, can better prevent the wardrobe from deformation!

1. Avoid placing items that are too heavy

Avoid placing items that are too heavy for a long time, otherwise the whole wardrobe will be deformed. No matter what material the whole wardrobe is made of, its function is to store light things such as clothes, and exceeding the upper limit of its load-bearing capacity will lead to deformation and even breakage.

2. Friction with hard objects should be avoided

The surface of the overall wardrobe should avoid friction with hard objects, so as not to damage the surface texture of the paint and wood, such as placing porcelain and bronze and other decorative items should be especially careful, it is best to pad a soft cloth.

3. Keep the floor where the wardrobe is located flat

Keep the ground where the whole wardrobe is located, the ground is uneven, and the overall wardrobe will be unevenly deformed due to the force for a long time, and the way to avoid it is to use small pieces of wood to pad it flat. If it is a bungalow or a house on low ground, the whole wardrobe must be properly raised if the ground is wet, otherwise the bottom of the wardrobe is easy to be corroded by moisture.

4. Avoid direct sunlight

Avoid putting the whole wardrobe in front of the window and the sun for a long time.

1. Metal strips can be added or woodworking boards can be used to "divide and conquer" to prevent the deformation of cabinet doors. The specific method is to cut a piece of woodworking board into 5 cm wide strips, each with a distance of 5 cm to form a door panel, and then paste decorative panels on the outside. This is because the larger the area, the more likely it is to deform.

If you cut it into small pieces and combine them, it will not be easy to deform.

2. The materials used on the front and back of the cabinet door should be as consistent as possible, and four panels should be used as much as possible. Paint as much as possible at the same time, don't paint one side and leave the other unpainted, or stay too far apart. This is because, if the material of the front and back of the door is different, the proportion of expansion and contraction is different, which can easily cause the panel to warp.

The same is true for paint, if the painting time is different or one side is painted and the other side is not painted, then it is easy to cause the panel to lift up with different shrinkage ratios.

3. The closing of the wood and the edge of the lines should be carried out after the paint enters the site. The lines have a certain degree of elasticity, and the expansion or contraction of the lines should be basically stabilized before the edge can be closed. If you close the mouth too early, the originally smooth line may be missing a gap after a while, and it will be difficult to remedy it at that time.

You can use these wardrobes properly, don't put something too heavy in the wardrobe to avoid deformation, and don't scrub with high temperatures.

Be sure to pay attention to moisture, and try not to open windows in rainy weather; Secondly, wooden furniture is very afraid of exposure to the sun, if the wardrobe can be directly exposed to the sun, it is best to close the curtains; Finally, pay attention to the maintenance method, do not wipe with corrosive detergents, if it is dirty, you can use clean water, and if there is oil, you can use neutral detergents.

Wardrobe is one of the important components of furniture in daily life, and it is also one of the large pieces that constitute bedroom furniture. According to market research and analysis, consumers are most dissatisfied with the warping and deformation of cabinet doors. In addition to the reasons for material and design, the influence of unfavorable factors in the processing process is the main reason for the bending and deformation of the long door of the high cabinet

First, the influence of putty.

When finishing the wardrobe door parts, many manufacturers use pig blood putty or glue putty in order to reduce the cost, because these two kinds of putty contain a lot of water, and the hygroscopicity of the substrate commonly used in panel furniture - MDF and particleboard is particularly strong, so when one side of the door panel parts is not coated with putty, and the other side is coated with this moisture-rich putty, it will make the door panel parts deform with moisture on one side.

2. Deformation caused by stacking of parts.

In the production process, some operators stack the plates at will for convenience, or the backing plate of the stacked plates is uneven, and even the plates are leaned against the wall, causing the plates to be deformed due to their own weight before entering the next process.

3. Improper coating treatment causes deformation of panel furniture components.

The influence of the internal stress of the coating will form a certain coating after the curing of the coating, even in the absence of external force, it will produce an internal stress, if this internal stress is not properly treated, it will become one of the main reasons for the bending and deformation of the cabinet door components.

Fourth, the finishing process causes deformation.

In the process of finishing, due to the improper use of technology and raw materials, the plate is deformed with the change of internal stress of the coating.

5. The influence of the drying process.

Many manufacturers in the production, when the plate is coated with putty or paint, it must be placed in the drying rack for natural drying, if the drying rack rod is too loose or uneven, it will also cause the cabinet door parts to be bent and deformed in the process of paint drying.

In addition, the following aspects need to be paid attention to in the maintenance of the wardrobe:

1.If you want to wax, it is best to choose a wax with a high concentration and is solid, silicone-free, so as not to damage the paint surface.

1. The depth of the wardrobe is not enough and the clothes are too large, which causes pressure on the door.

2. If there are sundries on the top of the cabinet, it will also cause pressure on the cabinet door.

3. Improper use, excessive force.

4. The quality of the door.

Whether an overall wardrobe is good or not, its edge banding is also very important. Whether the edge is good or not directly affects whether the cabinet is deformed. Small manufacturers and small workshops are not, the basic use of artificial edge banding, the effect of edge sealing is poor, and even fall off, deformation, affecting the normal use of the wardrobe.

Therefore, the quality of edge banding equipment is very important.

How to prevent clothes from getting out of shape:

1. Before the wardrobe is processed, the plates used should not be stacked at will, and should be placed in a dry place to avoid damage and deformation before use.

2. After the wall and ground are basically dry, the wardrobe should be placed, and the wooden materials near the wall, against the wall and the parts that are susceptible to moisture should be brushed with preservatives.

3. The moisture content of the board used in the wardrobe should be controlled at about 15%, the air humidity in the south is relatively high in the region, which should be controlled at about 15%, and in the north and drier areas, it should be controlled below 12%.

4. The materials for making wardrobes should be E0 level ecological boards and blockboards, and the use of deformable wood that is not environmentally friendly should be avoided.

The humidity is high, and there are too many other things, and it slowly deforms. That's how it is in my house.

Maybe it's a problem with the quality, or maybe it's been a long time.

Once the large wardrobe riser is deformed, it is difficult to repair, and the reason for the deformation is that the quality of the plate used is not good; The second is that the space in the wardrobe is too large, and there are too many items in the cabinet, and the third is the wardrobe with sliding doors, which constantly hits the vertical plate when it is opened and closed.

During construction, the stability of the riser must be strengthened, and the internal draft is used to raise the plate with layer keys, and the riser of the sliding door is connected with the shelf with wooden hail screws.