The lights are not on in a room but there is electricity in the socket?

There was electricity at the socket in one room, but the lights were off. This means that the socket and the light are not in the same circuit.

It is necessary to check whether the live wire of the electric light is electrified, whether the neutral wire is on, and whether the switch is intact and whether the bulb is damaged.

After completing the above repairs, my lights are ready to come on.

The lights in a room are not on, and the socket has electricity, this is the switch, the circuit, there is a problem with the circuit of the bulb, check the switch, the circuit of the bulb.

The lights in a room are not on, but the socket is electric, which means that the main valve outside is no problem, because these lines in the house are not different, so you can see if the switch to control the lights is on.

Hello friend, the light in a room is not on, but the socket has electricity, in this case it should be your bulb is broken, you can replace the bulb of a bulb, sometimes it will burn, this time is long, it is easy to break.

Now the standard wiring of electricians is a circuit for electric lights and a circuit for sockets, first check whether it is tripped, then check whether the bulb is broken, if there are no two cases, and finally check your line.

This is possible, and the ** and socket wires in the house are generally separated from two lines.

The lights are not on in one room, but there is electricity in the sockets! Nowadays, household electricity is generally wired separately from the socket and lighting circuits! So the lights don't turn on, you need to find the fault according to the line! Then exclude it!

Then check whether the bulb is broken, if the bulb is not broken, it is a problem with the wiring to check and repair.

According to your description, it is estimated that the light switch is broken or the light is broken, and it is recommended to replace the light and switch with a new one.

1. The lamp is broken;

2. The lighting circuit and the socket circuit of this room are controlled separately, and the lighting circuit is powered off;

3. Faults of wires, switches, lampholders, etc.

Since the socket and the light are two control circuits, you can check whether the air switch of the 1 control socket is tripping off. It's useless to press it back, you can't close the gate, 1 is generally in the socket line, there is a short circuit, you should check the socket in the line, which has a problem, troubleshooting, the switch can be closed. Each is the air switch is broken, you can change 1 to try.

1. The insurance of the socket has dropped (now the general lighting and socket of the residential house and the air conditioning socket are separated).

2. The socket is not plugged in properly (check whether there is poor contact between the two ends).

3. The socket is broken (the socket is aging, and there is a possibility of disconnection inside).

4. The switch on the socket is not turned on (some sockets have their own switch control).

Choosing a skill. In order to further standardize indoor wiring, reduce potential safety hazards and waste of repeated disassembly and assembly, and work with enterprises to create a consumer environment with peace of mind and good market order, the National Electrical and Intelligent Cooperation Alliance invited electrical experts to jointly launch a series of suggestions on "electrical appliances delivered to home safely", giving consumers detailed and effective knowledge from various aspects such as material selection, wiring, switch and socket design, and network TV line design. And guide consumers to choose the right home improvement company for themselves and how to communicate with designers in the home improvement process.

Answer: Electricity provides a lot of convenience in life, it can be said that modern life, everyone is inseparable from electricity, there will be a lot of sockets and lighting fixtures installed in the family, but if you want to use electrical products safely, wire installation is very critical, if you accidentally connect the wrong one, it may cause safety accidents. It is inevitable that there will be some fault problems when using electricity at home, so what is the matter with the lights and electricity when the socket is out of power? Let's take a look with Qeeka Home experts.

1. What is going on when the socket is out of power and the lamp is still powered, which is generally caused by a short circuit in the socket wire, and the socket and the lighting fixture are not installed on the same line. A short circuit of a socket is very likely to cause the main switch of the entire socket to trip, resulting in the socket without power, and the circuit where the lighting fixture is located has not been affected, so the lamp is still electrified, this situation needs to find someone to repair it in time.

Second, what to pay attention to in the wiring of home switches and sockets 1, pay attention to distinguish wires As we all know, there are three kinds of wires, namely live wires, neutral wires and ground wires, if they are connected wrongly, it is easy to have electrical safety problems, especially when the socket is wired, these three wires have specific connection points, generally l port is connected to the live wire, that is, red or brown wire, n port is connected to the neutral wire, which is a yellow wire, and the e port is connected to the wire, which is a two-color wire.

2. Pay attention to the installation height of the wall when installing the switch socket, pay attention to the installation height, the height of the general switch is relatively unified, and the height of the socket is inconsistent, it should be installed according to the use of electrical products, for example, the height of the air conditioning socket can not be too low, its height can not be less than the meter, the bathroom concealed socket can not be lower than the meter, and the kitchen and bathroom socket can not be lower than the meter.

First of all, to tell you, the light and the socket are two different circuit breakers, so if the circuit breaker of the lamp is good, the light will be on, and if the circuit breaker of the socket is broken, then the socket will definitely have no power. You can troubleshoot the fault in this way, find an electric pen, and measure whether there is no power in the holes of the two sockets on the socket in the living room, if there is no electricity, then go to your power switch box and measure whether there is electricity under each circuit breaker? If there is no electricity, then measure whether the upper end of the circuit breaker is electrified, if there is electricity at the upper end of the circuit breaker, it means that the circuit breaker is broken, and the circuit breaker can be replaced.

If this happens, there are generally two possibilities, the first one may be caused by poor contact with the socket. You can turn it on to check if the two wires are connected, and another possibility is that the power switch of your outlet is not pushed. So there is no electricity in the socket, and generally the socket at home has a master switch, which you can check.

Personally, I think this should be the problem of the air switch at home, after all, these air switches have special control sockets, and some of them are specially designed to control the line of the lamp.

Now the standard operation of wiring is a route of socket, a route of electric lights, no electricity in the socket, first check whether there is a trip, if your light line and socket line is a route, it is recommended that you find an electrician to check it, I hope it can help you.

The sockets and lights at home are controlled separately, check whether the switch in the distribution box has tripped, and restore the power supply when it is found and closed.

The light in the room has electricity, it does not mean that the socket is electric, the socket may be wired off, so there is no electricity.

The socket and the lamp are generally not sent by one way, the socket is sent independently through the switch of the distribution box, you check whether the distribution box has a switch tripped,

The reason why the lights are on, but the sockets have no power, is mainly because the sockets and lights in your home are not the same circuit, so they will not be affected. If there is a problem with the switch that controls the socket at home, such as a tripping situation, it will cause the socket to have no power, but the light is on.

Because the socket and the lamp line is not the same, the socket is not powered, check whether it is because of a short circuit caused by a short circuit in the socket, after the check, go to the electrical box to close the brake, if the oil falls off their own oil will not change the fuse, you can find a property or plumber to repair it.

Check the fuse, switch reset button, and switch inlet and outlet.

No, there is an empty opening in the electric switch, and I haven't pushed it up.

Check the switch, also the wire and socket-to-socket wiring.

It should be which line is burned, let's find someone to see.

It may be that the neutral wire of the socket circuit is broken or in poor contact. Measure it with a multimeter. Also, What is the voltage of the live wire of the outlet?

The dark line can also be checked, and the voltage or switch on and off at the distribution box and socket is measured, and the line is not required to be pulled out to check. Spending some money to find an electrician should not be a big problem, since the lights can be on.

All the sockets in the room are out of power but the lights are electric: pro All the sockets in the room are out of power but the lights are electrified, probably because the sockets are broken switch. First, if you find that multiple sockets in your home are powered off at the same time, regardless of whether the switch trips or not, you need to check the switch first.

If there is a "self-reset overvoltage and undervoltage tripping" on the branch switch of the socket circuit, it may lead to the power failure of the line, but there is no tripping. At this time, it needs to be manually If the power supply is not restored, it may be that the self-reset function of the self-reset overvoltage and undervoltage tripping is damaged, and then it needs to be replaced with a new one. Receptacle.

The second point is that the socket itself needs to be taken into account. If there is no fault in the distribution box, or if the individual socket is out of power, then it is necessary to focus on checking the socket.